View UPD17016_94314.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

DATA SHEET
PD17016, 17017
4-BIT SINGLE-CHIP MICROCONTROLLERS WITH DIGITAL TUNING SYSTEM HARDWARE
MOS INTEGRATED CIRCUIT
The PD17016 and 17017 are 4-bit single-chip CMOS microcontrollers equipped with hardware for digital tuning systems. The CPU employs the 17K architecture and can directly manipulate the data memory, execute various operations, and control the peripheral hardware with a single instruction. All the instructions are one-word 16-bit instructions. As the peripheral hardware, a prescaler that can operate at up to 150 MHz, PLL frequency synthesizer, and frequency counter for digital tuning systems, as well as many I/O ports, an LCD controller/driver, A/D converter, and D/A converter (PWM output) are provided. Therefore, a high-performance, state-of-the-art digital tuning system can be organized with a single chip. In addition to the PD17016 and 17017, a one-time PROM model for program evaluation, the PD17P005, is also available.
FEATURES
* 17K architecture: general-purpose register method * Program memory (ROM) 8 KB (3836 x 16 bits) : PD17016 16 KB (7932 x 16 bits) : PD17017 * General-purpose data memory (RAM) 320 x 4 bits: PD17016 432 x 4 bits: PD17017 * Instruction execution time 4.44 s (with 4.5-MHz crystal resonator) * Decimal operation * Table reference * Hardware for PLL frequency synthesizer Dual modulus prescaler (150 MHz max.), programmable divider, charge pump * A wealth of peripheral hardware General-purpose I/O ports, LCD controller/driver, serial interface, A/D converter, D/A converter (PWM output), BEEP output, frequency counter * Interrupt External: 1 Internal: 1 * Power-ON reset, reset by CE pin, and power failure detection circuit * Power-saving CMOS * Supply voltage: VDD = 5 V10%
Unless otherwise specified, the PD17017 is explained as the representative model in this document.
The information in this document is subject to change without notice. Document No. U10664EJ2V0DS00 (2nd edition) Date Published September 1996 P Printed in Japan
The mark
shows major revised points.
(c)
1996
PD17016, 17017
ORDERING INFORMATION
Part Number Package 80-pin plastic QFP (14 x 20 mm) 80-pin plastic QFP (14 x 20 mm)
PD17016GF-xxx-3B9 PD17017GF-xxx-3B9
Remark xxx indicates a ROM code number.
FUNCTIONAL OUTLINE OF PD17016 AND 17017
Item Program memory (ROM) * * Function 8 KB (3836 x 16 bits) : PD17016 16 KB (7932 x 16 bits) : PD17017 All internal ROM areas can be referenced as a table. 320 x 4 bits : PD17016 432 x 4 bits : PD17017 General register: 16 x 4 bits 4.44 s (with 4.5-MHz crystal resonator) 7 levels (stack can be manipulated) I/O port : 16 pins Input port : 8 pins Output port : 9 pins (+8: LCD segment pin) 1 pin Selectable frequency (200 Hz, 1 kHz, 3 kHz) 30 segments, 2 commons 1/2 duty, 1/2 bias, frame frequency: 125 MHz, drive voltage: VDD, segment pins multiplexed with key source pins: 16 8 pins can be used as output port pins (4 pins can be set in output mode at one time) Serial interface * 1 channel 3-wire (serial I/O) 8 bits x 2 channels (PWM output, output voltage: 16 V MAX.) 6 bits x 6 channels (successive approximation by software) 2 sources (maskable interrupt) External : 1 source (INT0 pin) Internal : 1 source (timer) 2 channels Timer carry Timer interrupt
General-purpose data memory (RAM)
* *
Instruction execution time Stack level General-purpose port
* * * * * *
BEEP output
LCD controller/driver
*
D/A converter A/D converter Interrupt
* * *
Timer
*
(1, 5, 100, 250 ms) (1, 5, 100, 250 ms)
Reset
* * *
Power-ON reset (on power application) Reset by CE pin (CE pin low level high level) Power failure detection function
2
PD17016, 17017
Item PLL frequency synthesizer Division mode * Two types Direct division mode Pulse swallow mode
Function
(VCOL pin : 30 MHz MAX.) (VCOL pin : 40 MHz MAX.) (VCOH pin : 150 MHz MAX.)
Reference frequency Charge pump Phase comparator Frequency counter
*
12 programmable frequencies 1, 1.25, 2.5, 3, 5, 6.25, 9, 10, 12.5, 25, 50, 100 kHz Two independent error out outputs Unlock detection by program Frequency measurement P1D3/FMIFC pin : 5 to 15 MHz P1D2/AMIFC pin : 0.1 to 1 MHz
* * *
Supply voltage Package
VDD = 5 V10% 80-pin plastic QFP (14 x 20 mm)
3
PD17016, 17017
PIN CONFIGURATION (Top View)
80-pin plastic QFP (14 x 20 mm, 0.8 mm pitch)
PD17016GF-xxx-3B9 PD17017GF-xxx-3B9
P0D0/ADC2 P0D1/ADC3 P0D2/ADC4 P0D3/ADC5 LCD0/KS0 LCD1/KS1 LCD2/KS2 LCD3/KS3 LCD4/KS4 LCD5/KS5 LCD6/KS6 LCD7/KS7 LCD8/KS8 LCD9/KS9
P0C2
P0C1 P0C0 P0A3 P0A2 P0A1 P0A0 P0B3 P0B2/SCK P0B1/SO P0B0/SI IC0 INT0 CE P1A3 P1A2 P1A1 P1A0 P1B3 P1B2/PWM1 P1B1/PWM0 P1B0/BEEP P1C3 P1C2 P1C1
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65
P0C3
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41
LCD10/KS10 LCD11/KS11 LCD12/KS12 LCD13/KS13 LCD14/KS14 LCD15/KS15 LCD16 LCD17 LCD18 LCD19 LCD20 LCD21 LCD22/P0E0 LCD23/P0E1 LCD24/P0E2 LCD25/P0E3 LCD26/P0F0 LCD27/P0F1 LCD28/P0F2 LCD29/P0F3 COM0 COM1 P2A0 VDD2
25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
P1D3/FMIFC
P1D2/AMIFC
VCOL
VCOH
P1D1/ADC1
P1D0/ADC0
GND
IC1
IC2
XOUT
EO0
P1C0
4
VDD1
EO1
IC3
XIN
PD17016, 17017
PIN NAME
ADC0-ADC5 AMIFC BEEP CE COM0, COM1 EO0, EO1 FMIFC GND IC0-IC3 INT0 KS0-KS15 LCD0-LCD29 P0A0-P0A3 P0B0-P0B3 P0C0-P0C3 P0D0-P0D3 : A/D converter input : AM intermediate frequency counter input : BEEP output : Chip enable input : LCD common signal output : Error out output : FM intermediate frequency counter input : Ground : Internal connection : External interrupt input : Key source signal output : LCD segment signal output : Port 0A : Port 0B : Port 0C : Port 0D P0E0-P0E3 P0F0-P0F3 P1A0-P1A3 P1B0-P1B3 P1C0-P1C3 P1D0-P1D3 P2A0 PWM0, PWM1 SCK SI SO VCOH VCOL VDD1, VDD2 XIN, XOUT : Port 0E : Port 0F : Port 1A : Port 1B : Port 1C : Port 1D : Port 2A : D/A converter output : Serial clock I/O : Serial data input : Serial data output : Local oscillation high input : Local oscillation low input : Power supply : Crystal resonator connection
5
PD17016, 17017
BLOCK DIAGRAM
P0A0-P0A3 P0B0-P0B3 P0C0-P0C3 P0D0-P0D3 P1A0-P1A3 P1B0-P1B3 P1C0-P1C3 P1D0-P1D3 P2A0 P0E0-P0E3 P0F0-P0F3 4 4 Instruction decoder Interrupt control INT0 SCK/P0B2 Serial interface SO/P0B1 SI/P0B0 4 4 RF 4 4 4 4 4 4 ALU Port RAM 320x4 bits ( PD17016) 432x4 bits ( PD17017) System reg. D/A converter A/D converter ADC5/P0D3 ADC2/P0D0 ADC1 ADC0 PWM1/P1B2 PWM0/P1B1 Frequency counter FMIFC/P1D3 AMIFC/P1D2
BEEP
BEEP/P1B0
COM0,COM1 LCD0/KS0 LCD15/KS15 LCD16 LCD21 LCD22/P0E0 LCD25/P0E3 LCD26/P0F0
LCD controller /driver
ROM 3836x16 bits ( PD17016) 7932x16 bits ( PD17017)
Timer
VDD1 Reset VDD2 CE GND PLL Stack 7x12 bits ( PD17016) 7x13 bits ( PD17017) Program counter
LCD29/P0F3 VCOH VCOL EO0 EO1
XIN XOUT
OSC
CPU Peripheral
6
PD17016, 17017
Contents
1. PIN FUNCTIONS ............................................................................................................................ 1.1 Pin Function List ................................................................................................................ 1.2 Notes on Using General-Purpose Port ............................................................................ 1.3 Equivalent Circuits of Pins ............................................................................................... 1.4 Processing of Unused Pins .............................................................................................. 1.5 Notes on Using CE and INT0 Pins ................................................................................... 2. PROGRAM MEMORY (ROM) ........................................................................................................ 2.1 Outline of Program Memory ............................................................................................. 2.2 Program Memory ................................................................................................................ 2.3 Program Counter ................................................................................................................ 2.4 Program Flow ..................................................................................................................... 2.5 Notes on Using Program Memory ................................................................................... 3. ADDRESS STACK (ASK) .............................................................................................................. 3.1 Outline of Address Stack .................................................................................................. 3.2 Address Stack Register (ASR) ......................................................................................... 3.3 Stack Pointer (SP) .............................................................................................................. 3.4 Operation of Address Stack ............................................................................................. 3.5 Notes on Using Address Stack ........................................................................................ 4. DATA 4.1 4.2 4.3 4.4 MEMORY (RAM) .................................................................................................................. Outline of Data Memory .................................................................................................... Configuration and Function of Data Memory ................................................................. Addressing of Data Memory ............................................................................................. Notes on Using Data Memory ..........................................................................................
12 12 17 18 22 23 24 24 25 26 26 28 29 29 29 31 32 32 33 33 34 36 37 38 38 39 40 42 43 44 46 48 49 50 50 50 51 52
5. SYSTEM REGISTER (SYSREG) ................................................................................................... 5.1 Outline of System Register .............................................................................................. 5.2 System Register List .......................................................................................................... 5.3 Address Register (AR) ....................................................................................................... 5.4 Window Register (WR) ....................................................................................................... 5.5 Bank Register (BANK) ....................................................................................................... 5.6 Index Register (IX) and Data Memory Row Address Pointer (MP: Memory Pointer) ... 5.7 General Register Pointer (RP) .......................................................................................... 5.8 Program Status Word (PSWORD) .................................................................................... 5.9 Notes on Using System Register ..................................................................................... 6. GENERAL REGISTER (GR) .......................................................................................................... 6.1 Outline of General Register .............................................................................................. 6.2 General Register Body ....................................................................................................... 6.3 Address Generation of General Register by Each Instruction ...................................... 6.4 Notes on Using General Register ....................................................................................
7
PD17016, 17017
7. ALU (Arithmetic Logic Unit) BLOCK .......................................................................................... 7.1 Outline of ALU Block ......................................................................................................... 7.2 Configuration and Function of Each Block ..................................................................... 7.3 ALU Processing Instruction List ...................................................................................... 7.4 Notes on Using ALU ........................................................................................................... 8. REGISTER FILE (RF) ..................................................................................................................... 8.1 Outline of Register File ...................................................................................................... 8.2 Configuration and Function of Register File .................................................................. 8.3 Control Registers ............................................................................................................... 8.4 Notes on Using Register File ........................................................................................... 9. DATA 9.1 9.2 9.3 9.4 BUFFER (DBF) .................................................................................................................... Outline of Data Buffer ........................................................................................................ Data Buffer .......................................................................................................................... Peripheral Hardware and Data Buffer List ...................................................................... Notes on Using Data Buffer .............................................................................................. 53 53 54 54 58 59 59 60 61 66 67 67 68 69 72 73 73 74 77 79 79 80 85 85 86 87 88
10. INTERRUPT ................................................................................................................................... 10.1 Outline of Interrupt Block ................................................................................................. 10.2 Interrupt Control Block ...................................................................................................... 10.3 Interrupt Stack Register.................................................................................................... 10.4 Stack pointer, address stack register, and program counter ........................................ 10.5 Interrupt Enable Flip-Flop (INTE) ..................................................................................... 10.6 Acknowledging Interrupts ................................................................................................ 10.7 Operation After Interrupt Has been Acknowledged ....................................................... 10.8 Restoring from Interrupt Processing Routine ................................................................ 10.9 External (INT0 Pin) Interrupt ............................................................................................. 10.10 Internal Interrupt ................................................................................................................ 10.11 Notes on Using Interrupt ..................................................................................................
11. TIMER FUNCTION ......................................................................................................................... 89 11.1 Configuration of Timer ....................................................................................................... 89 11.2 Functional Outline of Timer .............................................................................................. 90 11.3 Timer Carry ......................................................................................................................... 90 11.4 Timer Interrupt .................................................................................................................... 105 12. STANDBY ....................................................................................................................................... 114 12.1 Configuration of Standby Block ...................................................................................... 114 12.2 Standby Function ............................................................................................................... 115 12.3 Selecting Device Operation Mode with CE Pin ............................................................... 115 12.4 Halt Function ...................................................................................................................... 117 12.5 Clock Stop Function .......................................................................................................... 127 12.6 Device Operations in Halt and Clock Stop Status .......................................................... 130 12.7 Current Consumption in Halt Status and Clock Stop Status ........................................ 131
8
PD17016, 17017
13. RESET ............................................................................................................................................ 136 13.1 Configuration of Reset Block ........................................................................................... 136 13.2 Reset Function ................................................................................................................... 137 13.3 CE Reset ............................................................................................................................. 138 13.4 Power-ON Reset ................................................................................................................. 143 13.5 Relation between CE Reset and Power-ON Reset .......................................................... 146 13.6 Power Failure Detection ................................................................................................... 150 14. PLL FREQUENCY SYNTHESIZER ............................................................................................... 158 14.1 Configuration of PLL Frequency Synthesizer ................................................................ 158 14.2 Functional Outline of PLL Frequency Synthesizer ........................................................ 159 14.3 Input Select Block and Programmable Divider ............................................................... 160 14.4 Reference Frequency Generator ...................................................................................... 165 14.5 Phase Comparator (-DET), Charge Pump, and Unlock Detection Block .................... 167 14.6 PLL Disabled Status .......................................................................................................... 171 14.7 Using PLL Frequency Synthesizer .................................................................................. 171 14.8 Status on Reset .................................................................................................................. 175 15. GENERAL-PURPOSE PORT ......................................................................................................... 176 15.1 Configuration and Classification of General-Purpose Ports ......................................... 176 15.2 Functional Outline of General-Purpose Ports ................................................................ 178 15.3 General-Purpose I/O Ports (P0A, P0B, P0C, and P1A) ................................................... 183 15.4 General-Purpose Input Ports (P0D and P1D) .................................................................. 191 15.5 General-Purpose Output Ports (P1B, P1C, and P2A) ..................................................... 193 15.6 General-Purpose Output Ports (P0E and P0F) ............................................................... 195 16. A/D CONVERTER (ADC) ............................................................................................................... 198 16.1 Configuration of A/D Converter ....................................................................................... 198 16.2 Functional Outline of A/D Converter ............................................................................... 198 16.3 Input Select Block .............................................................................................................. 199 16.4 Compare Voltage Generation Block ................................................................................ 201 16.5 Compare Block ................................................................................................................... 204 16.6 Performances of A/D Converter ....................................................................................... 205 16.7 Using A/D Converter .......................................................................................................... 206 16.8 Notes on Using A/D Converter ......................................................................................... 211 16.9 Status on Reset .................................................................................................................. 211 17. D/A CONVERTER (DAC) ............................................................................................................... 212 17.1 Configuration of D/A Converter ....................................................................................... 212 17.2 Functional Outline of D/A Converter ............................................................................... 212 17.3 Output Select Blocks ......................................................................................................... 213 17.4 Duty Setting Blocks and Clock Generation Block .......................................................... 214 17.5 Status on Reset .................................................................................................................. 217 18. BEEP OUTPUT .............................................................................................................................. 218 18.1 Method of BEEP Output .................................................................................................... 218 18.2 Output Waveform of BEEP ............................................................................................... 219 18.3 Status on Reset .................................................................................................................. 219 18.4 Notes on Using BEEP Function ....................................................................................... 220
9
PD17016, 17017
19. SERIAL INTERFACE ..................................................................................................................... 221 19.1 Configuration of Serial Interface ...................................................................................... 222 19.2 Functional Outline of Serial Interface .............................................................................. 223 19.3 Shift Clock and Serial Data I/O Pin Control Blocks ........................................................ 224 19.4 Clock Generation Block .................................................................................................... 226 19.5 Clock Counter ..................................................................................................................... 228 19.6 Presettable Shift Register (SIO1SFR) .............................................................................. 229 19.7 Wait Block ........................................................................................................................... 232 19.8 Using Serial Interface ........................................................................................................ 234 19.9 Status of Serial Interface on Reset .................................................................................. 240 20. FREQUENCY COUNTER (FC) ....................................................................................................... 241 20.1 Configuration of Frequency Counter............................................................................... 241 20.2 Functional Outline of Frequency Counter ....................................................................... 241 20.3 Input Select Block and Gate Time Control Block ........................................................... 243 20.4 Start/Stop Control Block and IF Counter ........................................................................ 246 20.5 Using IF Counter Function ............................................................................................... 253 20.6 Status on Reset .................................................................................................................. 255 20.7 Notes on Using Frequency Counter ................................................................................ 256 21. LCD CONTROLLER/DRIVER ........................................................................................................ 258 21.1 Configuration of LCD Controller/Driver ........................................................................... 258 21.2 Functional Outline of LCD Controller/Driver ................................................................... 259 21.3 LCD Segment Register ...................................................................................................... 261 21.4 Output Timing Control Blocks and Segment/Port Select Block ................................... 266 21.5 Using LCD Controller/Driver ............................................................................................ 272 21.6 Status on Reset .................................................................................................................. 274 22. KEY SOURCE CONTROLLER/DECODER .................................................................................. 275 22.1 Configuration of Key Source Controller/Decoder .......................................................... 275 22.2 Functional Outline of Key Source Controller/Decoder .................................................. 276 22.3 Key Source Data Setting Block ........................................................................................ 277 22.4 Output Timing Control Blocks and Segment/Port Select Block ................................... 279 22.5 Key Input Control Block ................................................................................................... 283 22.6 Using Key Source Controller/Decoder ............................................................................ 286 22.7 Status on Reset .................................................................................................................. 294 23. INSTRUCTION SET ....................................................................................................................... 295 23.1 Outline of Instruction Set ................................................................................................. 295 23.2 Legend ................................................................................................................................ 296 23.3 Instruction Set List ............................................................................................................. 297 23.4 Assembler (AS17K) Embedded Macroinstruction .......................................................... 299 23.5 Software Macroinstructions ............................................................................................. 300 24. RESERVED SYMBOL .................................................................................................................... 302 24.1 Data Buffer (DBF) ............................................................................................................... 302 24.2 System Register (SYSREG) .............................................................................................. 302 24.3 LCD Segment Register ...................................................................................................... 303 24.4 Port Register ....................................................................................................................... 303 24.5 Register File (control register) ......................................................................................... 305 24.6 Peripheral Hardware Register .......................................................................................... 306 24.7 Others ................................................................................................................................. 306
10
PD17016, 17017
25. ELECTRICAL SPECIFICATIONS ................................................................................................. 307 26. PACKAGE ...................................................................................................................................... 310 27. RECOMMENDED SOLDERING CONDITIONS ............................................................................ 312 APPENDIX A. NOTE ON CONNECTING CRYSTAL RESONATOR .................................................. 313 APPENDIX B. DIFFERENCES AMONG PD17016, 17017, 17003A, 17005, AND 17010 ................ 314 APPENDIX C. DEVELOPMENT TOOLS ............................................................................................ 319
11
PD17016, 17017
1. PIN FUNCTIONS 1.1 Pin Function List
Pin No. 79 80 1 2 3 4 5 6 Symbol P0C3 P0C2 P0C1 P0C0 P0A3Note P0A2Note P0A1 P0A0 Function 4-bit I/O port. Can be set in input or output mode in 4-bit units. Output Form CMOS push-pull On Power-ON Reset Input
4-bit I/O port. Can be set in input or output mode in 1-bit units.
N-ch open drain, 5V (P0A3, P0A2) CMOS push-pull (P0A1, P0A0)
Input
7 8 9 10
P0B3 P0B2/SCK P0B1/SO P0B0/SI
Port 0B and serial interface I/O. * P0B3-P0B0 * 4-bit CMOS I/O port * Can be set in input or output mode in 1-bit units SCK, SO, SI * SCK : serial clock I/O * SO : serial data output * SI : serial data input
CMOS push-pull P0B3, P0B2/SCK, P0B1/SO P0B0
Input (P0B3-P0B0)
*
11
IC0
Internally connected. Connect this pin to VDD or GND via resistor. Edge-detectable vectored interrupt input (rising edge detection). This pin is a Schmitt trigger input pin with hysteresis characteristics. Do not apply a voltage higher than VDD to INT0 pin on power application; otherwise, normal operation will not be performed.
-
-
12
INT0
-
Input
Note
The P0A3 and P0B2 pins are N-ch open-drain output pins and must be connected to an external pull-up resistor.
12
PD17016, 17017
Pin No. 13 Symbol CE Function Selects operation of PD17017 and inputs reset signal. (1) Device operation selection PLL frequency synthesizer can operate when CE pin is high; it is automatically disabled (operation prohibited) while CE pin is low. (2) Reset signal input When CE pin goes high, device is reset in synchronization with internal basic timer 0 carry FF (CE reset). This pin does not accept low or high level of less than 110 to 165 s to prevent malfunctioning due to noise. Input signal level of this pin can be detected by CE pin level judge register of register file (address 07H). Contents of CE pin level judge register are not changed by low or high level of less than 110 to 165 s. This pin is a Schmitt trigger input pin with hysteresis characteristics. Do not apply voltage higher than VDD to this pin on power application; otherwise, normal operation will not be performed. 4-bit CMOS I/O port. Can be set in input or output mode in 1-bit units. Output Form - On Power-ON Reset Input
14 | 17 18 19 20 21
P1A3 | P1A0 P1B3Note P1B2/PWM1Note P1B1/PWM0Note P1B0/BEEP
CMOS push-pull
Input
Port 1B also serving as D/A converter and buzzer output pins. * P1B3-P1B0 * 4-bit output port * PWM1, PWM0 * D/A converter output with 8-bit resolution * BEEP * Buzzer output
N-ch open drain, 16 V P1B3, P1B2/PWM1, P1B1/PWM0 CMOS push-pull (P1B0/BEEP) CMOS push-pull
Outpus undefined data (P1B3-P1-B0)
22 | 25
P1C3 | P1C0
4-bit CMOS output port.
Outputs undefined data
Note
The P1B3, P1B2/PWM1, and P1B1/PWM0 pins are N-ch open-drain output pins and must be connected to an external pull-up resistor.
13
PD17016, 17017
Pin No. 26 27 28 29
Symbol P1D3/FMIFC P1D2/AMIFC P1D1/ADC1 P1D0/ADC0
Function Port 1D, frequency counter input, and analog input to A/D converter. * P1D3-P1D0 * 4-bit input port * FMIFC, AMIFC * Input to FM and AM intermediate frequency counter Measurable frequency Input Pin Input Frequency (MHz) 5-15 10.5-10.9 P1D2/AMIFC 0.1-1 0.44-0.46 Input Amplitude (Vp-p) 0.3 0.06 0.3 0.05
Output Form -
On Power-ON Reset Input (P1D3-P1D0)
P1D3/FMIFC
Because these pins are input pins of AC amplifier, cut DC components of input signals by using capacitor. * ADC1, ADC0 * Analog input to A/D converter with 6-bit resolution. 30 41 VDD1 VDD2 Positive power supply pins. Supply 5 V10% to these pins when CPU and peripheral functions operate. Data can be retained at 2.2 V when clock is stopped. When VDD rises, PD17017 is reset by internal power-ON reset circuit. Do not apply voltage higher than VDD pins (VDD1 and VDD2) to all pins other than VDD pins. Especially, exercise care in raising VDD and CE pins simultaneously because latch up may occur. Apply same voltage to VDD1 and VDD2 pins. VDD2 supplies power to crystal oscillation circuit (XIN and XOUT pins) and error out circuit (EO0 and EO1 pins), and VDD1 pin supplies power to other circuits. - -
14
PD17016, 17017
Pin No. 31 32
Symbol VCOL VCOH
Function Inputs local oscillation frequency to PLL. Two types of division modes are available: direct division (MF mode) and pulse swallow (HF and VHF modes). Division Mode Input Pin Input Frequency Input Voltage (MHz) (Vp-p) 0.5-30 5-40 9-150 0.2 0.2 0.2
Output Form -
On Power-ON Reset Input
Direct division (MF) Pulse swallow (HF) Pulse swallow (VHF)
VCOL VCOL VCOH
Because these pins are input pins of AC amplifier, cut DC components of input signal by using capacitor. 33 34 GND XOUT
Note
Ground Crystal resonator connecting pins. Connect crystal resonator of 4.5 MHz to these pins.
- CMOS push-pull -
- -
35
XINNote
36 37
EO0 EO1
Output from charge pump of PLL frequency synthesizer. If value resulting from dividing local oscillation (VCO) frequency input to VCOL (pin 31) or VCOH (pin 32) pin is higher than reference frequency, EO0 and EO1 pins output high level; if it is lower, these pins output low level. If two frequencies coincide, these pins are floated. Because EO0 and EO1 pins output same signals, both pins can be used. Internally connected pin. Connect this pin to VDD via resistor. Internally connected pins. Leave these pins unconnected.
CMOS 3-state
High impedance
38
IC1
-
-
39 40 42
IC2 IC3 IC2
-
-
1-bit CMOS output port.
CMOS push-pull
Outputs undefined data. Low-level output
43 44
COM1 COM0
Output common signals of LCD controller/driver. These pins output low level on execution of power-ON reset or clock stop instruction in display off mode.
CMOS3 ternary output
Note
Refer to APPENDIX A. NOTES ON CONNECTING CRYSTAL RESONATOR.
15
PD17016, 17017
Pin No. 45 48 49 | 52 53 | 58 59 | 74 75 | 78
Symbol LCD29/P0F3 | LCD26/P0F0 LCD25/P0E3 | LCD22/P0E0 LCD21 | LCD16 LCD15/KS15 | LCD0/KS0 P0D3/ADC5 | P0D0/ADC2
Function Port 0F, port 0E, segment signal output pins of LCD controller/driver, and key source signal output pins of key matrix.
Output Form CMOS push-pull
On Power-ON Reset Low-level output (LCD29-LCD0)
* P0F3-P0F0
* 4-bit CMOS output port
* P0E3-P0E0
* 4-bit CMOS output port
* LCD29-LCD0
* Segment signal output of LCD controller/driver.
* KS15-KS0
* Key source signal output of key matrix.
Port 0D, analog input to A/D converter, and key source signal return input of LCD segment. * P0D3-P0D0 * 4-bit input port * Internal pull-down resistor is always ON. * ADC5-ADC2 * Analog input to A/D converter with 6-bit resolution. * Internal pull-down resistor is OFF. * Key source return input * Internal pull-down resistor is ON only while key source is output (220 s) if LCD segment pin is used as key source, and OFF while LCD segment signal is output.
-
Input with pull-down resistor (P0D3-P0D0)
16
PD17016, 17017
1.2 Notes on Using General-Purpose Port
1.2.1 Data bit of port register Input data of ports 0A, 0B, 0C, 0D, 1A, 1B, 1C, 1D, and 2A are read, and output data is set to these ports via the respective port registers (P0A through P2A registers) on data memory. The P0A3 pin of port 0A correspond to the most significant bit of port register P0A, and the P0A0 pins correspond to the least significant bit. Likewise, the pins of the other ports, ports 0B, 0C, 0D, 1A, 1B, 1C, 1D, and 2A, correspond to the bits of the respective port registers. The output data of ports 0E and 0F are set by the LCD segment register on data memory. 1.2.2 I/O ports (ports 0A, 0B, 0C, and 1A) (1) When each port is set in input mode The status of each port pin is used as the value of the corresponding port register when an instruction that reads the contents of each port register on data memory is executed (when the address of a port register is specified as m of an instruction such as SKT m, #n4 and ADD r, m). When an instruction that writes data to each port register is executed (when a port register address is specified as r of an instruction such as MOV m, #n4 and ADD r, m), the value of the corresponding port is written to the output data latch circuit. (2) When each port is set in output mode When an instruction that writes data to each port register is executed, the value of the data is written to the data latch circuit, and output from the corresponding port pins. When an instruction that reads the contents of each port register is executed, the contents of the output data latch are used as the value of the port register. When an instruction that reads the contents of the port register corresponding to the P0A3 and P0A2 pins is executed, the statuses of the pins, which may be different from the output data, are read as is. All these port pins are set in the input mode on power-ON reset, CE reset, and execution of the clock stop instruction. Because the contents of the output data latch circuit are undefined on power-ON reset, undefined data may be output unless an instruction that writes data to the port register is executed before a port is set in the output mode. The contents of the output data latch circuit are not affected by CE reset or execution of the clock stop instruction. 1.2.3 Output ports (ports 1B, 1C, 0F, 0E, and 2A) An output port writes the value of the corresponding port register to the output data latch circuit and outputs it from each port pin when an instruction that writes data to the port register is executed. When an instruction that reads the value of the port register is executed, the status of the output data latch circuit is used as the value of the port register. Undefined data is output on power-ON reset. The current output data is retained on CE reset and execution of the clock stop instruction. However, ports 0E and 0F automatically output low levels on power-ON reset and execution of the clock stop instruction.
17
PD17016, 17017
1.3 Equivalent Circuits of Pins
(1) P0A (P0A1, P0A0) P0B (P0B3, P0B2/SCK, P0B1/SO, P0B0/SI) P0C (P0C3, P0C2, P0C1, P0C0)Note P1A (P1A3, P1A2, P1A1, P1A0)
VDD
(I/O)
RESET
VDD
Note
The RESET signal is not supplied to P0C.
(2) P0A (P0A3, P0A2) (I/O)
VDD
18
PD17016, 17017
(3) P1B (P1B0/BEEP) P1C (P1C3, P1C2, P1C1, P1C0) P2A (P2A0) LCD0/KS0-LCD29/P0F3
VDD
(Output)
(4) P1B (P1B3, P1B2/PWM1, P1B1/PWM0) (Output)
(5) P0D (P0D3/ADC5, P0D2/ADC4, P0D1/ADC3, P0D0/ADC2) (Input)
VDD A/D converter
High ON resistance
(6) P1D (P1D1/ADC1, P1D0/ADC0) (Input)
VDD A/D converter
19
PD17016, 17017
(7) P1D (P1D3/FMIFC, P1D2/AMIFC) (Input)
VDD
General-purpose
VDD
High ON resistance VDD
Frequency counter
(8) CE INT0
(Schmitt trigger input)
VDD
(9) XOUT (output), XIN (input)
VDD
High ON resistance VDD
XIN
Internal clock
High ON resistance XOUT
20
PD17016, 17017
(10) EO1 EO0
(output)
VDD
(11) COM1 COM0
(output)
VDD
VDD
High ON resistance
High ON resistance
(12) VCOH VCOL
(input)
VDD
High ON resistance VDD
High ON resistance
21
PD17016, 17017
1.4 Processing of Unused Pins
It is recommended that unused pins be processed as follows: Table 1-1. Processing of Unused Pins
Pin Name Port pins P0A0-P0A3 P0B0/SI P0B1/SO P0B2/SCK P0B3 P0C0-P0C3 P0D0/ADC2-P0D3/ADC5 Input Connect each port pin to GND via resistorNote 2. Open I/O Mode I/ONote 1 Recommended Processing Set general-purpose input port mode by software, and connect each port pin to VDD or GND via resistorNote 2.
P0E0/LCD22-P0E3/LCD25 CMOS push-pull output P0F0/LCD26-P0F3/LCD29 P1A0-P1A3 I/ONote 1
Set general-purpose input port mode by software, and connect each port pin to VDD or GND via resistorNote 2. Open Set low-level output by software and leave port pins open.
P1B0/BEEP P1B1/PWM0, P1B2/PWM1 P1B3 P1C0-P1C3 P1D0/ADC0, P1D1/ADC1 P1D2/AMIFCNote 3 P1D3/FMIFC P2A0 Pins other than port pins CE COM0, COM1 EO0, EO1 IC0 IC1 IC2, IC3 INT0 LCD0/KS0-LCD15/KS15 LCD16-LCD21 VCOH, VCOL
Note 3
CMOS push-pull output N-ch open drain output
CMOS push-pull output Input
Open Connect each pin to VDD or GND via resistorNote 2. Set port mode and connect each pin to VDD or GND via resistorNote 2.
CMOS push-pull output Input Output Output - - - Input Output
Open Connect to VDD via resistorNote 2. Open Open Connect to VDD or GND via resistorNote 2. Connect to VDD via resistorNote 2. Open Connect to VDD or GND via resistorNote 2. Open
Input
Disable PLL by software and leave pins open.
Notes 1. The I/O port pins are set in the input mode on power application, execution of the clock stop instruction, or CE reset. 2. If a port pin is externally pulled up (connect to VDD via resistor) or down (connect to GND via resistor) with a high resistance, the pin almost goes into a high-impedance state, and the current consumption (inrush current) of the port pin increases. Generally, the pull-up and pull-down resistances are several 10 k, although they vary depending on the application circuit. 3. Do not set these pins as AMIFC and FMIFC modes; otherwise, the current consumption will increase.
22
PD17016, 17017
1.5 Notes on Using CE and INT0 Pins
The CE and INT0 pins have a function to set a test mode (for IC test) in which the internal operations of the
PD17017 are tested, in addition to the functions listed in 1.1 Pin Function List.
If a voltage higher than VDD is applied to either of these pins, the test mode is set. Therefore, if noise exceeding VDD is applied to these pins even during normal operation, the test mode is set by mistake, affecting the normal operation. Noise may be superimposed on these pins if the length of the wiring of these pins is too long. Therefore, keep the wiring length as short as possible. If noise is inevitable, take noise suppression measures by using an external component as illustrated below. * Connect diode with low VF between CE or INT0 and VDD
VDD VDD
* Connect capacitor between CE or INT0 and VDD
Diode with low VF
VDD
VDD
CE, INT0
CE, INT0
23
PD17016, 17017
2. PROGRAM MEMORY (ROM) 2.1 Outline of Program Memory
Figure 2-1 outlines the program memory. As shown in this figure, the program memory consists of a program memory and a program counter. The addresses of the program memory are specified by the program counter. The program memory has the following two major functions. (1) Stores programs. (2) Stores constant data Figure 2-1. Outline of Program Memory
Program counter Program memory
***
Adddress specification
Instruction
***
Constant data
***
***
24
PD17016, 17017
2.2 Program Memory
Figure 2-2 shows the configuration of the program memory. As shown in this figure, the program memory is configured as follows:
PD17016: 3836 x 16 bits (0000H through 0EFBH) PD17017: 7932 x 16 bits (0000H through 1EFBH)
All "instructions" are "1-word instructions" 16 bits long, so that one instruction can be stored in one address of the program memory. Constant data reads the contents of the program memory to the data buffer by using a table reference instruction. Figure 2-2. Configuration of Program Memory
Address 0 0 0 0 H Reset start address 0001H 0002H 0 0 0 3 H Timer interrupt vector 0004H 0 0 0 5 H INT0 pin interrupt vector (with PD17016) BR addr instruction branch addressNote BR @AR instruction branch address (with PD17017)
BR addr instruction branch address BR @AR instruction branch address
CALL addr Page 0 instruction CALL @AR instruction subroutine subroutine entry entry address address
00FFH 07FFH
CALL @AR instruction MOVT DBF, @AR instruction subroutine entry table reference address address MOVT DBF, @AR instruction table reference address
0EFBH 0FFFH
(with PD17016)
Page 1
Page 2 17FFH Page 3 1EFBH (with PD17017) 16 bits
Note
Valid in the address 0000H through 0EFBH.
25
PD17016, 17017
2.3 Program Counter
Figure 2-3 shows the configuration of the program counter. The program counter specifies an address of the program memory. Bit PC11 of the PD17016, and PC11 and PC12 of the PD17017 indicate a page. Figure 2-3. Configuration of Program Counter
PC12 PC11 Page PC ( PD17016) PC10 PC9 PC8 PC7 PC6 PC5 PC4 PC3 PC2 PC1 PC0
Page PC ( PD17017)
2.4 Program Flow
The execution flow of the program is controlled by the program counter which specifies an address of the program memory. Figure 2-4 shows the value set to the program counter when each instruction is executed. Table 2-1 shows a vector address when an interrupt is acknowledged.
26
PD17016, 17017
Figure 2-4. Specification of Program Counter on Execution of Each Instruction (a) PD17016
Program counter Instruction BR addr Page 0 Page 1 CALL addr b11 b10 0 Instruction operand (addr) 1 0 Instruction operand (addr) BR @AR CALL @AR MOVT DBF, @AR RET RETSK RETI When interrupt is acknowledged Vector address of each interrupt Power-ON reset, CE reset 0 0 0 0 0 0 0 0 0 0 0 0 Contents of address stack register (ASR) specified by stack pointer (SP) (Return address) 0 0 0 0 Adddress register contents Contents of program counter (PC) b9 b8 b7 b6 b5 b4 b3 b2 b1 b0
(b) PD17017
Program counter Instruction BR addr Page 0 Page 1 Page 2 Page 3 CALL addr b12 b11 b10 0 0 1 1 0 0 1
Contents of program counter (PC) b9 b8 b7 b6 b5 b4 b3 b2 b1 b0
Instruction operand (addr) 0 1 0 Instruction operand (addr) BR @AR CALL @AR MOVT DBF, @AR RET RETSK RETI When interrupt is acknowledged Vector address of each interrupt Power-ON reset, CE reset 0 0 0 0 0 0 0 0 0 0 0 0 0 Contents of address stack register (ASR) specified by stack pointer (SP) (Return address) Adddress register contents
27
PD17016, 17017
Table 2-1. Interrupt Vector Address
Priority 1 2 Internal/External Internal External Interrupt Source INT0 pin Timer Vector address 0005H 0003H
2.5 Notes on Using Program Memory
The program memory of the PD17016 does not have addresses 0EFCH through 0FFFH, and that of the
PD17017 does not have addresses 1EFCH through 1FFFH. Therefore, do not use an instruction that causes
the value of the program counter to be set to these addresses.
28
PD17016, 17017
3. ADDRESS STACK (ASK) 3.1 Outline of Address Stack
Figure 3-1 outlines the address stack. The address stack consists of a stack pointer and address stack registers. The addresses of the address stack registers are specified by the stack pointer. The address stack saves a return address when a subroutine call instruction is executed or when an interrupt is acknowledged. The address stack is also used when a table reference instruction is executed. Figure 3-1. Outline of Address Stack
Stack pointer Address specification
Address stack register
Return address
3.2 Address Stack Register (ASR)
Figure 3-2 shows the configuration of the address stack registers. There are eight 16-bit address stack registers: ASR0 through ASR7. Actually, however, no register is assigned to ASR7, and seven registers, ASR0 through ASR6, are used. The high-order 4 bits of ASR0 through ASR6 of the PD17016 are fixed to "0", and the high-order 3 bits of the address stack registers of the PD17017 are fixed to "0". The address stack saves a return address when a subroutine call instruction or table reference instruction is executed, or when an interrupt is acknowledged.
29
PD17016, 17017
Figure 3-2. Configuration of Address Stack Registers (a) PD17016
Stack pointer (SP) Bit b3 b2 b1 b0 0H ASR0 1H ASR1 2H ASR2 3H ASR3 4H ASR4 5H ASR5 6H ASR6 7H ASR7 (undefined) Cannot be used Address b11 b10 b9 b8 b7 b6 Bit b5 b4 b3 b2 b1 b0 Address stack register (ASR)
0 SP2 SP1 SP0
(b) PD17017
Stack pointer (SP) Bit b3 b2 b1 b0 0H Address
Address stack register (ASR)
Bit b12 b11 b10 b9 b8 b7 b6 ASR0 b5 b4 b3 b2 b1 b0
0 SP2 SP1 SP0
1H ASR1 2H ASR2 3H ASR3 4H ASR4 5H ASR5 6H ASR6 7H ASR7 (undefined) Cannot be used
30
PD17016, 17017
3.3 Stack Pointer (SP)
3.3.1 Configuration and function of stack pointer Figure 3-3 shows the configuration and function of the stack pointer. The stack pointer is a 4-bit binary counter. It specifies the address of an address stack register. The value of the stack pointer can be directly read or written by using a register manipulation instruction. Figure 3-3. Configuration and Function of Stack Pointer
Name Flag Symbol b3 Stack pointer SP 0 b2 S P 2 b1 S P 1 b0 S P 0 01H Address Read/ Write R/W
Specifies address of address stack register (ASR) 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 Address 0 (ASR0) Address 1 (ASR1) Address 2 (ASR2) Address 3 (ASR3) Address 4 (ASR4) Address 5 (ASR5) Address 6 (ASR6) Address 7 (ASR7)
Fixed to "0"
On reset
Power-ON Clock stop CE
0
1 1 1
1 1 1
1 1 1
31
PD17016, 17017
3.4 Operation of Address Stack
3.4.1 On execution of subroutine call ("CALL addr", "CALL @AR") or return ("RET", "RETSK") instruction When a subroutine call instruction is executed, the value of the stack pointer is decremented by one and a return address is saved to the address stack register specified by the stack pointer. When a return instruction is executed, the contents (return address) of the address stack register specified by the stack pointer are restored to the program counter, and the value of the stack pointer is incremented by one. 3.4.2 On execution of table reference instruction ("MOVT DBF, @AR") When a table reference instruction is executed, the value of the stack pointer is decremented by one, and a return address is saved to the address stack register specified by the stack pointer. Next, the contents of the program memory specified by the address register are read to the data buffer, the contents (return address) of the address stack register specified by the stack pointer are restored to the program counter, and then the value of the stack pointer is incremented by one. 3.4.3 On acknowledging interrupt and execution of return instruction ("RETI") When an interrupt is acknowledged, the value of the stack pointer is decremented by one, and the return address is saved to the address stack register specified by the stack pointer. When a return instruction is executed, the contents (return address) of the address stack register specified by the stack pointer are restored to the program counter, and the value of the stack pointer is incremented by one. 3.4.4 On execution of address stack manipulation instruction ("PUSH AR", "POP AR") When the "PUSH" instruction is executed, the value of the stack pointer is decremented by one, and the contents of the address register are transferred to the address stack register specified by the stack pointer. When the "POP" instruction is executed, the contents of the address stack register specified by the stack pointer are transferred to the address register, and the value of the stack pointer is incremented by one.
3.5 Notes on Using Address Stack
3.5.1 Nesting level The value of the address stack register (ASR7) is "undefined" when the value of the stack pointer is 07H. Do not use a subroutine call or interrupt exceeding level 7 without manipulating the stack; otherwise, execution returns to an "undefined address".
32
PD17016, 17017
4. DATA MEMORY (RAM) 4.1 Outline of Data Memory
Figure 4-1 outlines the data memory. As shown in this figure, the data memory consists of a general-purpose data memory, system register, data buffer, LCD segment register, and port registers. The data memory stores data, transfers data with the peripheral hardware units, sets display data, transfers data with the ports, and controls the CPU. Figure 4-1. Outline of Data Memory
Peripheral hardware Data transfer Column address 0 0 1 Row address 2 3 4 5 6 7 Port register Port register Port register BANK0 LCD segment register BANK1 BANK2 BANK3Note System register Data transfer Port LCD Data transfer 1 2 3 4 5 6 7 8 9 A B C D E F
Data buffer
Note
BANK3 is not provided on the PD17016.
33
PD17016, 17017
4.2 Configuration and Function of Data Memory
Figure 4-2 shows the configuration of the data memory. As shown in the figure, the data memory consists of banks. Each bank consists of 128 nibbles with 7H row addresses and 0FH column addresses. The data memory can be divided by classification of function into the blocks explained in the following 4.2.1 through 4.2.6. The contents of the data memory can be operated, compared, judged, and transferred in 4-bit units by using a data memory manipulation instruction. Table 4-1 lists the available data memory manipulation instructions. 4.2.1 System register (SYSREG) The system register is allocated to addresses 74H through 7FH. Because the system register is allocated to every bank, the identical system register exists at addresses 74H through 7FH of any bank. For details, refer to 5. SYSTEM REGISTER (SYSREG). 4.2.2 Data buffer (DBF) The data buffer is allocated to addresses 0CH through 0FH of BANK0. For details, refer to 9. DATA BUFFER (DBF). 4.2.3 LCD segment data register (LCD segment register) The LCD segment register is allocated to addresses 60H through 6FH of BANK0. For details, refer to 21. LCD CONTROLLER/DRIVER. 4.2.4 Port data registers (port registers) The port registers are allocated to addresses 70H through 73H of each bank. For details, refer to 15. GENERAL-PURPOSE PORT. 4.2.5 General-purpose data memory The general-purpose data memory is allocated to the addresses of the data memory excluding those of the system register, LCD segment register, and port registers. (a) PD17016 The general-purpose data memory of the PD17016 consists of a total of 320 nibbles (320 x 4 bits): 96 nibbles of BANK0, and 112 nibbles each of BANK1 and BANK2. (b) PD17017 The general-purpose data memory of the PD17017 consists of a total of 432 nibbles (432 x 4 bits): 96 nibbles of BANK0, and 112 nibbles each of BANK1 through BANK3. 4.2.6 Data memory not provided Data memory areas to which nothing is actually allocated exist in the LCD segment register and part of the port registers. For the details of these data memory areas, refer to 4.4.2 Notes on data memory area not provided, 15. GENERAL-PURPOSE PORT, and 21. LCD CONTROLLER/DRIVER.
34
PD17016, 17017
Figure 4-2. Configuration of Data Memory
Column address 0123456789ABCDEF
0 1 2 3 4 5 6 7
Row address
Data memory
BANK0 BANK1 BANK2 BANK3Note 1
System register
0 0 1
1
2
3
4
5
Column address 6789A
B
C
D
E
F
Data buffer (DBF)
Row address
2 3 4 5 6 7 Port register 0 0 1 2 3 4 5 6 7 Port register 0 0 1 1 2 3 4 5 6 System register (SYSREG) 7 8 9 A B C D E F BANK1 1 2 3 4 5 6 BANK0 LCD segment register System register (SYSREG) 7 8 9 A B C D E F General register
Example Address 1AH of BANK0 b3 b2 b1 b0
Row address Row address
2 3 4 5 6 7 Port register 0 0 1 1 2 3 4 5 6 System register (SYSREG) 7 8 9 A B C D E F BANK2
Row address
2 3 4 5 6 7
Note Note Note Note 2 2 2 2
BANK3Note 1
System register (SYSREG)
Same system register exists.
Notes 1. BANK3 is not provided on the PD17016. 2. BANK3 does not have addresses 70H through 73H.
35
PD17016, 17017
Table 4-1. Data Memory Manipulation Instructions
Function Operation Addition ADD ADDC SUB SUBC AND OR XOR SKE SKGE SKLT SKNE MOV LD ST SKT SKF Instruction
Subtraction
Logical
Compare
Transfer
Judgement
4.3 Addressing of Data Memory
Figure 4-3 shows addressing of the data memory. An address of the data memory is specified by a bank, a row address, and a column address. The row address and column address are directly specified by using a data memory manipulation instruction. The bank is specified by the contents of the bank register. For the details of the bank register, refer to 5. SYSTEM REGISTER (SYSREG). Figure 4-3. Addressing of Data Memory
Bank b3 b2 b1 b0 Row address b2 b1 b0 Column address b3 b2 b1 b0
Bank Data memory address M register Instruction operand
36
PD17016, 17017
4.4 Notes on Using Data Memory
4.4.1 On power-ON reset The contents of the general-purpose data memory are "undefined" on power-ON reset. Initialize the general-purpose data memory as necessary. 4.4.2 Notes on data memory area not provided If a data memory manipulation instruction is executed to an address of the data memory area not provided, the following operations are performed. (1) Device operation If a read instruction is executed, "0" is read. Nothing is affected even if a write instruction is executed. (2) Assembler operation Assembly is performed normally. An "error" does not occur. (3) In-circuit emulator operation If a read instruction is executed, "0" is read. Nothing is affected even if a write instruction is executed. An "error" does not occur.
37
PD17016, 17017
5. SYSTEM REGISTER (SYSREG) 5.1 Outline of System Register
Figure 5-1 shows the location of the system memory on the data memory and the outline of the system register. As shown in this figure, the system register is allocated to addresses 74H through 7FH of each bank of the data memory. Therefore, an identical system register exists at addresses 74H through 7FH of any bank. Because the system register is located on the data memory, it can be manipulated by any data memory manipulation instruction. The system register consists of seven registers. Figure 5-1. Location on Data Memory and Outline of System Register
Column address 0 0 1 2 3 4 5 6 7 1 2 3 4 5 6 7 8 9 A B C D E F
Data memory
Row address
BANK0 BANK1 BANK2 BANK3Note System register
Note BANK3 is not provided on the PD17016.
Address Name
74H Address register (AR)
75H
76H
77H
78H Window register (WR) Transfers data with register file.
79H Bank register (BANK) Specifies bank of data memory.
Function
Controls program memory address.
Address Name
7AH Index register (IX)
7BH
7CH
7DH General register pointer (RP)
7EH
7FH Program status word (PSWORD)
Data memory row address pointer (MP) Function Modifies address of data memory. Specifies address of general register
Controls operation.
38
PD17016, 17017
5.2 System Register List
Figure 5-2 shows the configuration of the system register. Figure 5-2. Configuration of System Register
Address Name 74H 75H 76H System register Address register (AR) Window register (WR) Symbol AR3 AR2 AR1 AR0 WR Bank register (BANK) BANK 77H 78H 79H
Bit Data
b3 0
b2 0
b1 0
b0 0
b3 0
b2 0
b1 0
b0 0
b3
b2
b1
b0
b3
b2
b1
b0
b3
b2
b1
b0
b3 0
b2 0
b1
b0
( PD17016)
0
0
0
( PD17017)
0
0
Address Name
7AH
7BH
7CH System register
7DH
7EH
7FH
Index register (IX) Data memory row address pointer (MP) Symbol IXH MPH Bit Data M P E (IX) 0 0 (MP) 0 0 b3 b2 b1 b0 b3 IXM MPL b2 b1 b0 b3 b2 b1 b0 b3 b2 IXL
General register pointer (RP)
Program status word (PSWORD)
RPH
RPL
PSW
b1
b0
b3
b2
b1
b0
b3
b2
b1
b0
B (RP) 0 C D
C M P
C Y
Z
I X E
39
PD17016, 17017
5.3 Address Register (AR)
5.3.1 Configuration of address register Figure 5-3 shows the configuration of the address register. As shown in this figure, the address register consists of 16 bits, or 74H through 77H (AR3 through AR0) of the system register. The high-order 8 bits of this register of the PD17016 are fixed to "0", and the high-order 3 bits of the address register of the PD17017 are fixed to "0". Figure 5-3. Configuration of Address Register
Address Name Symbol Bit DataNote 0 b3
74H
75H
76H
77H
Address register (AR) AR3 b2 0 b1 0 b0 0 b3 0 M S B 0 0 0 M S B AR2 b2 0 b1 0 b0 0 b3 AR1 b2 b1 b0 b3 AR0 b2 b1 b0
( PD17016) L S B
( PD17017)
L S B 0 0 0 0 0 0 0 0 0
On reset
Power-ON Clock stop CE
0 0 0
Remark Power-ON : power-ON reset Clock stop : execution of clock stop instruction CE Note : CE reset
Bits marked "0" are fixed to 0.
40
PD17016, 17017
5.3.2 Function of address register The address register specifies a program memory address when a table reference ("MOVT DBF, @AR"), stack manipulation ("PUSH AR", "POP AR"), indirect branch ("BR @AR") or indirect subroutine call ("CALL @AR") instruction is executed. A dedicated instruction ("INC AR") that can increment the value of the address register by one is also available. The following paragraphs (1) through (5) explain the operations to be performed when the respective instructions are executed. The address register can set the following range of the program memory addresses.
PD17016 : 0000H through 00FFH PD17017 : 0000H through 1EFBH
Do not set an address other than above to the address register. (1) Table reference instruction ("MOVT DBF, @AR") This instruction reads the constant data (16-bit) of the program memory address specified by the contents of the address register to the data buffer. (2) Stack manipulation instructions ("PUSH AR", "POP AR") When the "PUSH AR" instruction is executed, the value of the stack pointer is decremented by one, and the contents of the address register (AR) are stored to the address stack register specified by this value of the stack pointer. When the "POP AR" instruction is executed, the contents of the address stack register specified by the stack pointer are transferred to the address register, and the value of the stack pointer are incremented by one. (3) Indirect branch instruction ("BR @AR") This instruction branches execution to the program memory address specified by the contents of the address register. (4) Indirect subroutine call instruction ("CALL @AR") This instruction calls the subroutine at the program memory address specified by the contents of the address register. (5) Address register increment instruction ("INC AR") This instruction increments the contents of the address register by one. (a) With PD17016 Because the address register of the PD17016 consists of 8 bits, its contents are cleared to "0000H" if the "INC AR" instruction is executed when the contents of the address register are "00FFH". (b) With PD17017 Because the address register of the PD17017 consists of 13 bits, its contents are cleared to "0000H" if the "INC AR" instruction is executed when the contents of the address register are "1FFFH". 5.3.3 Address register and data buffer The address register can transfer data via the data buffer as part of the peripheral hardware. For details, refer to 9. DATA BUFFER (DBF).
41
PD17016, 17017
5.4 Window Register (WR)
5.4.1 Configuration of window register Figure 5-4 shows the configuration of the window register. As shown in the figure, the window register consists of 4 bits at address 78H of the system register. Figure 5-4. Configuration of Window Register
Address Name 78H Window register (WR) Symbol Bit Data b3 M S B WR b2 b1 b0 L S B
On reset
Power-ON Clock stop CE
Undefined Holds previous status
5.4.2 Function of window register The window register is used to transfer data with register file (RF) that is explained later. To transfer data between the window register and register file, dedicated instructions "PEEK WR, rf" and "POKE rf, WR" are used (rf: address of register file). The following paragraphs (1) and (2) explain the operations to be performed when each of these instructions is executed. Also refer to 8. REGISTER FILE (RF). (1) "PEEK WR, rf" instruction When this instruction is executed, the contents of the register file addressed by "rf" are transferred to the window register. (2) "POKE rf, WR" instruction When this instruction is executed, the contents of the window register are transferred to the register file addressed by "rf".
42
PD17016, 17017
5.5 Bank Register (BANK)
5.5.1 Configuration of bank register Figure 5-5 shows the configuration of the bank register. As shown in the figure, the bank register consists of 4 bits at address 79H (BANK) of the system register. Actually, however, this register is a 2-bit register because the high-order 2 bits are always fixed to "0". Figure 5-5. Configuration of Bank Register
Address Name 79H Bank register (BANK) Symbol Bit Data 0 0 M S B L S B b3 BANK b2 b1 b0
On reset
Power-ON Clock stop CE
0 0 0
5.5.2 Function of bank register The bank register specifies a bank of the data memory. Table 5-1 shows the relation between the value of the bank register and a bank of the data memory specified by each value of the bank register. Because the bank register exists on the system register, its contents can be rewritten no matter which bank may be currently specified. In other words, the bank register can be manipulated independently of the current status of the bank. Table 5-1. Specifying Bank of Data Memory
Bank register (BANK) b3 0 0 0 0 b2 0 0 0 0 b1 0 0 1 1 b0 0 1 0 1 BANK0 BANK1 BANK2 BANK3 Note Data memory bank
Note
BANK3 is not provided on the PD17016. Do not set this bank with the PD17016.
43
PD17016, 17017
5.6 Index Register (IX) and Data Memory Row Address Pointer (MP: Memory Pointer)
5.6.1 Configuration of index register and data memory row address pointer Figure 5-6 shows the configuration of the index register and data memory row address pointer. As shown in the figure, the index register consists of an index register (IX) and an index enable flag (IXE). IX is a 11-bit register consisting of the low-order 3 bits (IXH) of system register address 7AH, and addresses 7BH and 7CH (IXM and IXL). IXE is the least significant bit of address 7FH (PSW). The data memory row address pointer (memory pointer) consists of a data memory row address pointer, which consists of 7 bits with the low-order 3 bits of address 7AH (MPH) and address 7BH (MPL), and a data memory row address pointer enable flag (memory pointer enable flag: MPE), which is the most significant bit of address 7AH (MPH). In other words, the high-order 7 bits of the index register are shared with the data memory row address pointer. Note, however, that the high-order 2 bits of the index register and data memory row address pointer (bits b2 and b1 of address 7AH) are always fixed to "0". Figure 5-6. Configuration of Index Register and Data Memory Row Address Pointer
Address Name 7AH 7BH Index register (IX) Memory pointer (MP) Symbol IXH MPH Bit Data M S B 0 0 M S B IX L S B MP L S B I X E b3 b2 b1 b0 b3 IXM MPL b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 IXL 7CH 7EH 7FH Program status word (PSWORD) PSW
On reset
Power-ON Clock stop CE
0 0 0
0 0 0
0 0 0
0 0 0
44
PD17016, 17017
5.6.2 Functions of index register and data memory row address pointer The index register and data memory row address pointer modify the addresses of the data memory. The following paragraphs (1) and (2) explains the functions of the index register and data memory row address pointer, respectively. A dedicated instruction ("INC IX") that can increment the value of the address register by one is also available. For details on address modification, refer to 7. ALU (Arithmetic Logic Unit) BLOCK. (1) Index register The index register modifies a specified data memory address according to the contents of the index register when a data memory manipulation instruction is executed. This modification, however, is valid only when the IXE flag is set to "1". To modify an address, the bank, row address, and column address of the data memory are ORed with the contents of the index register, and the instruction is executed to the data memory whose address (called an actual address) is specified by the result of this OR operation. All the data memory manipulation instructions are subject to address modification by the index register. The following instructions are not subject to modification by the index register. INC INC MOVT PUSH POP PEEK POKE GET PUT BR BR AR IX DBF, @AR AR AR WR, rf rf, WR DBF, p p, DBF addr @AR RORC r CALL addr CALL @AR RET RETSK RETI EI DI STOP s HALT h NOP
(2) Data memory row address pointer The data memory row address pointer modifies the address at the indirect transfer destination when a general register indirect transfer instruction ("MOV @r, m" or "MOV m, @r") is executed. However, this modification is valid only when the MPE flag is set to "1". To modify the address, the bank and row address at the transfer destination are replaced with the contents of the data memory row address pointer. Instructions other than the general register indirect transfer instructions are not subject to address modification. (3) Index register increment instruction ("INC IX") This instruction increments the contents of the index register by one. Because the index register is configured of 9 bits, the contents of the index register are cleared to "000H" if the "INC IX" instruction is executed when the contents of the index register are "1FFH".
45
PD17016, 17017
5.7 General Register Pointer (RP)
5.7.1 Configuration of general register pointer Figure 5-7 shows the configuration of the general register pointer. As shown in this figure, the general register pointer consists of 7 bits: 4 bits of address 7DH (RPH) of the system register and the high-order 3 bits of address 7EH (RPL). However, because the high-order 3 bits of address 7E are always fixed to 0, actually the low-order 4 bits of this register (the lowest 1 bit of address 7DH and the high-order 3 bits of address 7EH) are valid. Figure 5-7. Configuration of General Register Pointer
Address Name
7DH
7EH
General register pointer (RP)
Symbol Bit Data 0 b3
RPH b2 0 b1 0 b0 M S B b3
RPL b2 b1 L S B b0 B C D
On reset
Power-ON Clock stop CE
0 0 0
0 0 0
46
PD17016, 17017
5.7.2 Function of general register pointer The general register pointer specifies a general register on the data memory. Figure 5-8 shows the address of the general register specified by the general register pointer. As shown in the figure, the high-order 4 bits of the general register pointer (RPH: address 7DH) specify a bank, and the low-order 3 bits (RPL: address 7EH) specify a row address. Because the valid number of bits of the general register pointer is 4, the row addresses (0H through 7H) of BANK0 and BANK1 can be specified as general registers. For the details on the operations of the general registers, refer to 6. GENERAL REGISTER (GR). Figure 5-8. Address of General Register Specified by General Register Pointer
General register pointer (RP) RPH b3 0 b2 0 b1 0 b0 M S B b3 RPL b2 b1 L S B b0 B C D
Specifies row address of each bank Specifies bank Bank 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 0 1 0 1 BANK0 Row address 0H 1H 2H 3H
1 1 1 1
1 1 1 1
0 0 1 1
0 1 0 1 BANK1
4H 5H 6H 7H
Caution
Because the valid number of bits of the general register pointer is 4, BANK2 and BANK3 cannot be specified.
5.7.3 Notes on using general register pointer The least significant bit of address 7EH (RPL) to which the general register pointer is allocated is used as the BCD flag of the program status word. When rewriting the value of RPL, therefore, pay attention to the value of the BCD flag.
47
PD17016, 17017
5.8 Program Status Word (PSWORD)
5.8.1 Configuration of program status word Figure 5-9 shows the configuration of the program status word. As shown in the figure, the program status word consists of 5 bits: the least significant bit of address 7EH (RPL) of the system register and the 4 bits of the address 7FH (PSW). The program status word consists of five flags, each of which functions independently: BCD (BCD), compare (CMP), carry (CY), zero (Z), and index enable (IXE) flags. Figure 5-9. Configuration of Program Status Word
Address Name 7EH (RP) 7EH Program status word (PSWORD) Symbol Bit Data b3 RPL b2 b1 b0 B C D b3 C M P PSW b2 C Y b1 Z b0 I X E
On reset
Power-ON Clock stop CE
0 0 0
0 0 0
48
PD17016, 17017
5.8.2 Function of program status word The program status word is a register that sets the condition of an operation or transfer instruction of the ALU (Arithmetic Logic Unit) or indicates the result of an operation executed. Table 5-2 outlines the function of each flag of the program status word. For details, refer to 7. ALU (Arithmetic Logic Unit) BLOCK. Table 5-2. Functional Outline of Program Status Word
(RP) Program status word (PSWORD) RPL b3 b2 b1 b0 B C D b3 C M P PSW b2 C Y b1 Z b0 I X E Flag Name Index enable flag (IXE) Function This flag modifies address of data memory when data memory manipulation instruction is executed. 0 : Does not modify 1 : Modifies Zero flag (Z) This flag indicates that result of arithmetic operation executed is 0. Note that status of 0 or 1 differs depending on content of compare flag. Carry flag (CY) This flag indicates occurrence of carry or borrow as result of execution of addition or subtraction instruction. It is reset to "0" if carry/borrow does not occur; it is set to "1" if carry/borrow occurs. This flag is also used as sift bit of "RORC r" instruction. Compare flag (CMP) This flag is used to not store result of arithmetic operation to data memory or general register. 0 : Result stored 1 : Result not stored BCD flag (BCD) This flag is used to execute arithmetic operation in decimal. 0 : Executes binary operation 1 : Executes decimal operation
5.8.3 Notes on using program status word If an arithmetic operation (addition or subtraction) instruction is executed to the program status word, the "result" of the arithmetic operation is stored to the program status word. For example, even if an operation that causes a carry to occur is executed, if the result of the operation is 0000B, 0000B is stored to PSW.
5.9 Notes on Using System Register
The data of the system register fixed to "0" is not affected even if a write instruction is executed to it. This data is always "0" when it is read.
49
PD17016, 17017
6. GENERAL REGISTER (GR) 6.1 Outline of General Register
Figure 6-1 outlines the general register. As shown in the figure, the general register consists of a general register pointer and general register body. The bank and row address of the general register body are specified by the general register pointer. The general register body is used to transfer data and execute operation between data memory addresses. Figure 6-1. Outline of General Register
Column address Data memory General register
Row address
General register Transfer, operation
pointer
BANK0 BANK1 BANK2 BANK3Note System register
Note
BANK3 is not provided to the PD17016. Because the valid number of bits of the general register pointer is 4, BANK2 and BANK3 cannot be specified.
Caution
6.2 General Register Body
The general register body consists of 16 nibbles (16 x 4 bits) at the same row addresses on the data memory. For the range of the banks and row addresses that can be specified by the general register pointer and general register, refer to 5.7 General Register Pointer (RP). The 16 nibbles of the same row address specified as a general register executes operation and transfers data with the data memory with a single instruction. In other words, operation or transfer between data memory addresses can be executed with a single instruction. The general register can be controlled by a data memory manipulation instruction like the other data memory areas.
50
PD17016, 17017
6.3 Address Generation of General Register by Instructions
The following subsections 6.3.1 and 6.3.2 explains how the addresses of the general register are generated when each instruction is executed. For the details of the operation of each instruction, refer to 7. ALU (Arithmetic Logic Unit) BLOCK. 6.3.1 Addition ("ADD r, m", "ADDC r, m"), subtraction ("SUB r, m", "SUBC r, m"), logical operation ("AND r, m", "OR r, m", "XOR r, m"), direct transfer ("LD r, m", "ST m, r"), and rotation processing ("RORC r") instructions Table 6-1 shows the address of general register "R" specified by operand "r" of an instruction. Only specify a column address as operand "r". Table 6-1. Address Generation of General Register
Bank b3 b2 b1 b0 Row address Column address b2 b1 b0 b3 b2 b1 b0
Contents of general General register address R register pointer r
6.3.2 Indirect transfer ("MOV @r,m", "MOV m, @r") instructions Table 6-2 shows the address of the general register "R" specified by operand "r" of an instruction and an indirect transfer address specified by "@R". Table 6-2. Address Generation of General Register
Bank b3 b2 b1 b0 Row address Column address b2 b1 b0 b3 b2 b1 b0
Contents of general General register address R register pointer r
Indirect transfer address
@R
Same as data memory
Contents of R
51
PD17016, 17017
6.4 Notes on Using General Register
6.4.1 Row address of general register Note that because the row address of the general register is specified by the general register pointer, the bank currently specified may differ from the bank of the general register. 6.4.2 Operation between general register and immediate data No instruction that executes an operation between the general register and immediate data is provided. To execute an operation between the general register and immediate data, the general register must be treated as a data memory area.
52
PD17016, 17017
7. ALU (Arithmetic Logic Unit) BLOCK 7.1 Outline of ALU Block
Figure 7-1 outlines the ALU block. As shown in the figure, the ALU block consists of an ALU, temporary registers A and B, program status word, decimal adjustment circuit, and data memory address control circuit. The ALU operates, judges, compares, rotates, and transfers 4-bit data on the data memory. Figure 7-1. Outline of ALU Block
Data bus
Address control
Temporary register A
Temporary register B
Program status word
Index modification memory pointer
Carry/borrow/ zero detection/decimal/ storage specification ALU * Arithmetic operation * Logical operation * Bit judgment * Comparison * Rotation processing * Transfer
Data memory
Decimal adjustment
53
PD17016, 17017
7.2 Configuration and Function of Each Block
7.2.1 ALU The ALU executes arithmetic or logical operation, bit judgment, comparison, rotation processing, and transfer of 4-bit data according to an instruction specified by the program. 7.2.2 Temporary registers A and B Temporary registers A and B temporarily store 4-bit data. These registers are automatically used when an instruction is executed and are not controlled by the program. 7.2.3 Program status word The program status word controls the operation of the ALU and stores the status of the ALU. For the details on the program status word, refer to 5.8 Program Status Word (PSWORD). 7.2.4 Decimal adjustment circuit If the BCD flag of the program status word is set to "1" as a result of an arithmetic operation executed, the arithmetic operation result is converted into a decimal number by the decimal adjustment circuit. 7.2.5 Address control circuit The address control circuit specifies an address of the data memory. At this time, address modification by the index register and data memory row address pointer is also controlled.
7.3 ALU Processing Instruction List
Table 7-1 lists the ALU operations when each instruction is executed. Table 7-2 shows modification of data memory addresses by the index register and data memory row address pointer. Table 7-3 shows the decimal adjustment data when a decimal operation is executed.
54
PD17016, 17017
Table 7-1. List of ALU Processing Instruction Operations
ALU Function
Instruction Difference in Operation due to Program Status Word (PSWORD) Value of Value of BCD flag CMP flag Addition ADD r, m m, #n4 ADDC r, m m, #n4 0 0 Arithmetic operation Stores result of Operation of CY flag Set if carry or Set if result of operation is 0000B; otherwise, reset. Executed Operation of Z flag Address Modification Index Memory pointer Not executed
-----------------------------------------------------------------------------------------------------------------------------------------
0
binary operation. borrow occurs; 1 Does not store result of binary operation. 0 Stores result of decimal operation. 1 Does not store result of decimal operation. Any (held) Not affected Holds previous status.
otherwise, reset. Holds status if result of operation is 0000B; otherwise, reset. Set if result of operation is 0000B; otherwise, reset. Holds status if result of operation is 0000B; otherwise, reset. Holds previous status. Executed Not executed
Subtraction
SUB
r, m m, #n4
1
SUBC
r, m m, #n4
1
Logical operation
OR
r, m m, #n4
Any (held)
AND
r, m m, #n4
XOR
r, m m, #n4
Judgment SKT SKF Compare SKE SKNE SKGE SKLT Transfer
m, #n m, #n m, #n4 m, #n4 m, #n4 m, #n4
Any (held) Any (held)
Any
Not affected
Holds previous status.
Holds previous status.
Executed
Not executed
(reset) Any (held) Not affected
Holds previous status.
Holds previous status.
Executed
Not executed
LD
ST MOV
r, m
m, r m, #n4 @r, m m, @r
Any (held)
Any (held)
Not affected
Holds previous status
Holds previous status
Executed
Not executed
Executed
Rotation
RORC
r
Any (held)
Any (held)
Not affected
Value of general Holds previous value register b0
Not
Not
executed executed
55
PD17016, 17017
Table 7-2. Modification of Data Memory Address and Modification of Indirect Transfer Address by Index Register and Data Memory Row Address Pointer
IXE MPE General register address specified by r Data memory address specified by m Bank Row address Column address Bank Row address Column address
Indirect transfer address specified by @r Bank Row address Column address
b3 b2 b1 b0 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b2 b1 b0 b3 b2 b1 b0 0 0 RP r BANK m BANK mR (r)
0
1 ditto ditto MP (r)
1
0 ditto
BANK Logical IX
m OR
BANK Logical IXH, IXM
mR OR (r)
1
1 ditto ditto MP (r)
BANK IX IXE IXH IXM IXL m mR mC MP MPE r RP (x) x
: : : : : : : : : : : : : : :
bank register index register index enable flag bits 10 through 8 of index register bits 7 through 4 of index register bits 3 through 0 of index register data memory address indicated by mR, mC data memory row address (high-order) data memory column address (low-order) data memory row address pointer memory pointer enable flag general register column address general register pointer contents addressed by x direct address such as m and r
56
PD17016, 17017
Table 7-3. Decimal Adjustment Data
Operation Result Hexadecimal Addition Decimal Addition Operation Result Hexadecimal Subtraction Decimal Subtraction
CY
0 0
Operation Result 0000B
CY
0
Operation Result 0000B 0
CY
0
Operation Result 0000B
CY
0
Operation Result 0000B
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
0001B 0010B 0011B 0100B 0101B 0110B 0111B 1000B 1001B 1010B 1011B 1100B 1101B 1110B 1111B 0000B 0001B 0010B 0011B 0100B 0101B 0110B 0111B 1000B 1001B 1010B 1011B 1100B 1101B 1110B 1111B
0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
0001B 0010B 0011B 0100B 0101B 0110B 0111B 1000B 1001B 0000B 0001B 0010B 0011B 0100B 0101B 0110B 0111B 1000B 1001B 1110B 1111B 1100B 1101B 1110B 1111B 1100B 1101B 1010B 1011B 1100B 1101B
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 -16 -15 -14 -13 -12 -11 -10 -9 -8 -7 -6 -5 -4 -3 -2 -1
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
0001B 0010B 0011B 0100B 0101B 0110B 0111B 1000B 1001B 1010B 1011B 1100B 1101B 1110B 1111B 0000B 0001B 0010B 0011B 0100B 0101B 0110B 0111B 1000B 1001B 1010B 1011B 1100B 1101B 1110B 1111B
0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
0001B 0010B 0011B 0100B 0101B 0110B 0111B 1000B 1001B 1100B 1101B 1110B 1111B 1100B 1101B 1110B 1111B 1100B 1101B 1110B 1111B 0000B 0001B 0010B 0011B 0100B 0101B 0110B 0111B 1000B 1001B
Remark The operation results in the shaded portion are not correctly adjusted by the decimal adjustment circuit.
57
PD17016, 17017
7.4 Notes on Using ALU
7.4.1 Notes on using operation to program status word If an arithmetic operation is executed on the program status word, the result of the arithmetic operation is stored in the program status word. The CY and Z flags of the program status word are set or reset depending on the result of the arithmetic operation. If an arithmetic operation is executed on the program status word itself, the result of the operation is stored in the program status word, which makes it impossible to judge occurrence of a carry or a borrow, or whether the result of the operation is zero. If the CMP flag is set, however, the result of the operation is not stored in the program status word, so that the CY and Z flags are set or reset normally. 7.4.2 Notes on using decimal operation A decimal operation can be executed only if the result falls within the following range: (1) Result of addition : 0 to 19 in decimal
(2) Result of subtraction : 0 to 9 or -10 to -1 in decimal If a decimal operation is executed exceeding this range, the CY flag is set, and the result is a value greater than 1010B (0AH).
58
PD17016, 17017
8. REGISTER FILE (RF) 8.1 Outline of Register File
Figure 8-1 outlines the register file. As shown in the figure, the register file consists of control registers existing on a space different from that of the data memory, and a portion overlapping the data memory. The control registers set the conditions of the peripheral hardware units. Data are read from or written to the register file via the window register. Figure 8-1. Outline of Register File
Register file 0 Control registers (separate space from data memory) Peripheral hardware
1
2
Row address
3
4
(Space same as data memory) Data is manipulated via window register
5
6
7 System register
Window register
59
PD17016, 17017
8.2 Configuration and Function of Register File
Figure 8-2 shows the configuration of and relation with the data memory of the register file. Addresses are allocated to the register file in 4-bit units, like the data memory, and the register file has a total of 128 nibbles with row addresses 0H through 7H and column addresses 0H through 0FH. Control registers that set the conditions of the peripheral hardware units are allocated to addresses 00H through 3FH. Addresses 40H through 7FH overlap the data memory. To put it another way, the addresses 40H through 7FH of the register file are the memory addresses of the bank currently selected of the data memory. These addresses, 40H through 7FH, can be treated in the same manner as the normal data memory areas, except that they can be manipulated by a register file manipulation instruction ("PEEK WR, rf" or "POKE rf, WR"), because they overlap the data memory. Figure 8-2. Configuration of Register File and Its Relation with Data Memory
Column address 0 0 1 Data memory 1 2 3 4 5 6 7 8 9 A B C D E F
Row address
2 3 4 5 6 7 BANK0 BANK1 BANK2 BANK3Note System register
0 1 Control register 2 3 Register file
Note
BANK3 is not provided to the PD17016.
60
PD17016, 17017
8.2.1 Register file manipulation instructions ("PEEK WR, rf" and "POKE rf, WR") Data are read from or written to the register file via the window register in the system register by using a register file manipulation instruction ("PEEK WR, rf" or "POKE rf, WR"). The operation of each instruction is explained below. (1) "PEEK WR, rf" This instruction reads the data of the register file addressed by "rf" to the window register. (2) "POKE rf, WR" This instruction writes the data of the window register to the register file addressed by "rf".
8.3 Control Registers
Figure 8-3 shows the configuration of the control registers. As shown in this figure, a total of 64 nibbles (64 words x 4 bits) at addresses 00H through 3FH of the register file can be used as control registers. Of these nibbles, however, 19 nibbles are actually used. The remaining 45 nibbles are unused registers that are prohibited from being read or written. Each control register has an attribute of 1 nibble, and is classified into four types: read/write (R/W), readonly (R), write-only (W), and read-and-reset (R & Reset). Nothing is changed even if data is written to a read-only (R and R & Reset) register. An "undefined" value is read if a write-only (W) register is read. Of the 4-bit data in 1 nibble, the bit fixed to "0" is always "0" when it is read or written. The 45 nibbles of unused registers are undefined when they are read, and nothing is changed when data is written to them.
61
PD17016, 17017
Figure 8-3. Configuration of Control Registers (1/2)
Colum address Row address 0 (8)
Item Name
0
1 Stack pointer (SP)
2 Serial I/O mode select S I O 1 C K 1 S I O 1 C K 0
3
4 I/F count gate judge 0 0 0 I0 F C G O S T T 0
5
6
7 CE pin level judge 0A0 D C C M P 0 0C E
PLL unlock A/D converter FF judge compare judge 0P0 L L U L 0
Symbol
SS SSSSI I PPPPOO 321011 TH SI Z ( ( ( ( ( R/W (
(
(
Read/ Write 1 (9) Name LCD mode select Symbol 0 0K S E N L C D E N
R/W
R
R & Reset
R
R
IF counter mode select I F C M D 1 I F C M D 0 I F C C K 1 I F C C K 0
A/D converter channel select A D C C H 3 A D C C H 2 A D C C H 1 A D C C H 0 0
Key input judge 0
Timer carry FF judge
0K0 E Y J
0
0B T M 0 C Y
Read/ Write 2 (A) Name
R/W
R/W
R & Reset
R & Reset
R & Reset
PLL mode select
IF counter control
Port 0C group I/O select
Symbol
P L L M D 3
P L L M D 2
P L L M D 1
P L L M D 0
0
0
I F C S T R T W
I F C R E S
0
0
0P 0 C G I O
Read/ Write 3 (B) Name
R/W
R/W
PLL reference mode select
Port 1A bit I/O select
Port 0B bit I/O select P 1 A B I O 0 P 0 B B I O 3 P 0 B B I O 2 P 0 B B I O 1 P 0 B B I O 0 P 0 A B I O 3
Port 0A bit I/O select P 0 A B I O 2 P 0 A B I O 1 P 0 A B I O 0
Symbol
P L L R F C K 3
P L L R F C K 2
P L L R F C K 1
P L L R F C K 0
P 1 A B I O 3
P 1 A B I O 2
P 1 A B I O 1
Read/ Write
R/W
R/W
R/W
R/W
62
PD17016, 17017
Figure 8-3. Configuration of Control Registers (2/2)
8
9 Timer mode select B T M 1 C K 1 B T M 1 C K 0 B T M 0 C K 1 B T M 0 C K 0
A
B
C
D
E
F
R/W
63
PD17016, 17017
Table 8-1. Outline of Peripheral Hardware Control Functions of Control Registers (1/3)
Peripheral hardware Name Control register Address Read/ Write b3 b2 Symbol b1 b0 Stack Stack pointer (SP) 01H R/W Peripheral hardware control function Functional outline Set value Power ON On reset Clock stop CE
------------------------------------------(SP0) (SP1) (SP2)
(SP3)
0 7 Stack pointer 7 7
Timer
Timer mode select
09H
R/W
------------------------------------------BTM0CK0 0 BTM0CK1 BTM1CK0
BTM1CK1
0 0 1 1 100 ms 250 ms 5 ms 1 ms interrupt time. 0 1 1 1 ------------------------------0 0 1 1 Sets time of 100 ms 250 ms 5 ms 1 ms timer carry FF. 0 1 1 1 Sets timer
0
0
Retained
Timer carry FF judge
17H
R& Reset
------------------------------------------BTM0CY 0 0 Detects timer carry FF 0: FF reset, 1: FF set 0 1 1 0
Pin
CE pin level judge
07H
R
------------------------------------------CE 0 0 Detects CE pin status 0: low level, 1: high level - - - 0
PLL frequency synthesizer
PLL unlock FF judge
05H
R& Reset
----------------------------0 0: lock, 1: unlock Undefined Retained Retained Detects unlock FF status 0 0 Sets division mode of PLL Sets reference frequency of PLL 0 Selects pin used for A/D converter 0:AD0 1:AD1 2:AD2 3:AD3 4:AD4 5:AD5 6:7:Input port 7 7 7 0 0 disable MF 0 1 1 VHF 0 1 HF 1 0 0 Retained Read & reset 0
--------------PLLUL PLL mode select 21H R/W
------------------------------------------PLLMD0 PLLMD1 PLLMD2
PLLMD3
PLL reference mode select
31H
R/W
----------------------------PLLRFCK1 PLLRFCK2
PLLRFCK3
0:1.25 kHz 1:2.5 kHz 2:5 kHz 3:10 kHz 4:6.25 kHz 5:12.5 kHz 6:25 kHz 7:50 kHz 8:3 kHz C:1 kHz 9:A:B: setting prohibited D:9 kHz E:100 kHz F: off
F
F
Retained
--------------PLLRFCK0 ADCCH3 A/D converter A/D converter channel select 14H R/W
----------------------------ADCCH1 ADCCH2
--------------ADCCH0 0 A/D converter compare judge 06H R
----------------------------0 0
--------------ADCCMP
Detects result of comparison by A/D converter
0:VREF>VADCIN 1:VREFUndefined Retained Retained
- : Determined by the status of the pin.
64
PD17016, 17017
Table 8-1. Outline of Peripheral Hardware Control Functions of Control Registers (2/3)
Peripheral hardware Name Control register Address Read/ Write b3 b2 Symbol b1 b0 Generalpurpose port Port 0C group I/O select 27H R/W Peripheral hardware control function Functional outline Set value Power ON On reset Clock stop CE
----------------------------0 0
0
--------------P0CGIO
Sets synchronously input/output mode of P0C3-P0C0 pins P1A3 pin P1A2 pin P1A1 pin P1A0 pin P0B3 pin P0B2 pin P0B1 pin P0B0 pin P0A3 pin P0A2 pin P0A1 pin P0A0 pin
Sets start of serial interface.
0: Input,
1: Output
0
0
0
Port 1A bit I/O select
35H
R/W
----------------------------P1ABIO1 P1ABIO2
P1ABIO3
--------------P1ABIO0 Port 0B bit I/O select 36H R/W
Sets input/ output mode of each port pin 0: Input, 1: Output 0 0 0
----------------------------P0BBIO1 P0BBIO2
P0BBIO3
--------------P0BBIO0 Port 0A bit I/O select 37H R/W
----------------------------P0ABIO1 P0ABIO2
P0ABIO3
--------------P0ABIO0 SIO1TS Serial interface Serial I/O mode select 02H R/W
----------------------------SIO1CK1 SIO1CK0 SIO1HIZ
------------------------------------------------------------0 0 1 1 External 75 kHz 150 kHz 450 kHz 0 1 0 1 0 0 0
0: Does not operate, 1: Starts
Sets P0B1/SO pin. 0: General-purpose port, 1: Serial out Sets clock of serial interface.
--------------Frequency counter IF counter gate judge 04h R
----------------------------0 0
0
--------------IFCGOSTT
Detects opening/ closing of gate of frequency counter Selects frequency counter/BEEP mode.
0: Close,
1: Open
0
Undefined Undefined
IF counter mode select
12H
R/W
--------------IFCMD0
IFCMD1
--------------IFCCK1
--------------IFCCK0 0 IF counter control 23H R/W
0 0 1 1 Setting BEEP FMIF AMIF prohibited 0 1 0 1 ------------------------------Sets gate time 0 0 1 1 of frequency 1 ms 4 ms 8 ms Open counter. 0 1 1 1
0
0
Retained
--------------0
--------------IFCSTRT
Specifies start of frequency counter.
0: NOP instruction, 1: Start
0
0
Retained
--------------IFCRES
Specifies data reset of frequency counter.
0: NOP instruction, 1: Reset
65
PD17016, 17017
Table 8-1. Outline of Peripheral Hardware Control Functions of Control Registers (3/3)
Peripheral hardware Name Control register Address Read/ Write b3 b2 Symbol b1 b0 LCD driver LCD mode select 10H R/W Peripheral hardware control function Functional outline Set value Power ON On reset Clock stop CE
----------------------------KSEN Sets key source signal output. Sets LCD display output. 0: Key source off, 1: Key source on 0: Display off, 1: Display on 0 0 Retained 0
0
--------------LCDEN
Key input judge
16H
R& Reset
--------------0
0
--------------0
--------------KEYJ
Detects key input latch of LCD key source
0: No latch, 1: Latch
0
Undefined Undefined
8.4 Notes on Using Register File
Bear in mind the following points (1) through (3) when manipulating the write-only registers (W), read-only registers (R), and unused registers of the control registers (addresses 00H through 3FH of the register file). (1) When a write-only register is read, an "undefined value" is read. (2) Nothing is changed even if data is written to a read-only register. (3) An "undefined value" is read if an unused register is read. Nothing is changed even if data is written to an unused register.
66
PD17016, 17017
9. DATA BUFFER (DBF) 9.1 Outline of Data Buffer
Figure 9-1 outlines the data buffer. The data buffer is located on the data memory and has the following two functions: (1) Reads constant data on program memory (table reference) (2) Transfers data with peripheral hardware unit Figure 9-1. Outline of Data Buffer
Data buffer
Data write (PUT) Table reference (MOVT)
Data read (GET)
Peripheral hardware
Constant data
Program memory
67
PD17016, 17017
9.2 Data Buffer
9.2.1 Configuration of data buffer Figure 9-2 shows the configuration of the data buffer. As shown in the figure, the data buffer consists of a total of 16 bits at addresses 0CH through 0FH of BANK 0 on the data memory. The 16-bit data consists of bit b3 at address 0CH as the MSB and bit b0 at address 0FH as the LSB. Because the data buffer is located on the data memory, it can be manipulated by all data memory manipulation instructions. Figure 9-2. Configuration of Data Buffer
Column address 0 0 1 2 1 2 3 4 5 6 7 8 9 A B C D E F
Data buffer (DBF)
Row address
3 4 5 6 7 7 7 7 System register BANK0 BANK1 BANK2 BANK3Note Data memory
Note BANK3 is not provided on the PD17016
Address Data memory Bit Bit Signal Data buffer Data M S B
0CH
0DH
0ED
0FH
b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0 DBF3 DBF2 DBF1 DBF0 L S Data B
68
PD17016, 17017
9.2.2 Table reference instruction ("MOVT DBF, @AR") This instruction reads the contents of the program memory addressed by the contents of the address register to the data buffer. One stack level is used when the table reference instruction is used. With the PD17017 all the addresses of the program memory can be referenced by this instruction, but with the PD17016 only the address 0000H through 00FFH can be referenced. 9.2.3 Peripheral hardware control instructions ("PUT", "GET") The operations of the "PUT" and "GET" instructions are as follows: (1) GET DBF, p This instruction reads the data of the peripheral register addressed by p to the data buffer. (2) PUT p, DBF This instruction sets the data of the data buffer to the peripheral register addressed by p.
9.3 Peripheral Hardware and Data Buffer List
Table 9-1 lists the peripheral hardware units and the functions of the data buffer.
69
PD17016, 17017
Table 9-1. Relations between Peripheral Hardware and Data Buffer (1/2)
Peripheral hardware Peripheral register that transfers data with data buffer Name Symbol Peripheral address Execution of PUT/GET instruction PUT/GET PUT/GET
A/D converter Serial interface Serial interface 1 (SIO1) PWM0 pin PWM1 pin
A/D converter data register Presettable shift register
ADCR SIO1SFR
02H 03H
D/A converter (PWM output)
PWM data register 0 PWM data register 1
PWMR0 PWMR1
05H 06H
PUT/GET
-----------------------------------------------------------------------------------------------------
Address register (AR) PLL frequency synthesizer Key source controller/decoder Frequency counter
Address register PLL data register Key source data register IF counter data register
AR PLLR KSR IFC
40H 41H 42H 43H
PUT/GET PUT/GET PUT/GET GET
70
PD17016, 17017
Table 9-1. Relations between Peripheral Hardware and Data Buffer (2/2)
Function Number of I/O bits of data buffer 8 Number of bits actually used 6 Outline
Sets compare voltage VREF data of A/D converter VREF = Sets serial out data and reads serial in data.
x - 0.5 64
x VDD, 1 x 63
8
8
8
8
Sets duty factor of output signal of D/A converter. Duty D = x + 0.25 256 Frequency f = 878.9 Hz x 100 %, 0 x 255
16 16 16 16
13Note 16 16 16
Transfers data with address register. Sets division ratio (N value) of PLL. Sets output data of key source signal. Reads count value of frequency counter.
Note
8 bits in the case of the PD17016.
71
PD17016, 17017
9.4 Notes on Using Data Buffer
Bear in mind the following points (1) through (3) concerning unused peripheral address and write-only peripheral registers (PUT only) and read-only peripheral registers (GET only) when transferring data with the peripheral hardware units via the data buffer. (1) When a write-only register is read, an "undefined value" is read. (2) Nothing is changed even if data is written to a read-only register. (3) An "undefined value" is read if an unused register is read. Nothing is changed even if data is written to an unused register.
72
PD17016, 17017
10. INTERRUPT 10.1 Outline of Interrupt Block
Figure 10-1 outlines the interrupt block. As shown in the figure, the interrupt block temporarily stops the program currently being executed in response to an interrupt request output from any peripheral hardware unit and branches execution to an interrupt vector address. The interrupt block consists of an "interrupt control block" for each peripheral hardware unit, "interrupt enable flip-flop" that enables all the interrupts, "stack pointer" that is controlled when an interrupt is acknowledged, "address stack register", "program counter", and "system register stack". The "interrupt control block" of each peripheral hardware unit consists of an "interrupt request flag (IRQxxx)" that detects each interrupt request, "interrupt permission flag (IPxxx)" that enables each interrupt, and "vector address generator (VAG)" that specifies a vector address when an interrupt is acknowledged. The peripheral hardware units that have an interrupt function are as follows: * INT0 pin (rising-edge detection) * Timer Figure 10-1. Outline of Interrupt Block
Interrupt control block IPTM flag IRQTM flag Vector address generator 03H Stack pointer Address stack register
Program counter
Timer
IP0 flag IRQ0 flag Vector address generator 05H System register
INT0 pin
Interrupt stack register
DI, EI instruction
Interrupt enable flip-flop
73
PD17016, 17017
10.2 Interrupt Control Block
The interrupt control block is provided to each peripheral hardware unit and detects an interrupt request, enables the interrupt, and generates a vector address when the interrupt is acknowledged. 10.2.1 Configuration and function of interrupt request flag (IRQxxx) Each interrupt request flag (IRQxxx) is set to "1" when an interrupt request is issued from the corresponding peripheral hardware unit, and is reset to "0" when the interrupt is acknowledged. It cannot be set by software. Once this flag has been set to "1", it is not reset until the corresponding interrupt is acknowledged or an interrupt request reset macro is executed. If more than one interrupt request is issued at the same time, the interrupt request flag corresponding to the interrupt that has not been acknowledged is not reset. Table 10-1 shows the software macros that reset interrupt requests. These macros are defined in the device file and can be used by INCLUDEing the files supplied with the device file (D17016.INC for the PD17016 and D17017.INC for the PD17017) on the source program. Table 10-1. Software Macros That Reset Interrupt Requests
Function Resets timer interrupt request. Resets INT0 pin interrupt request. Macro Name CLR1_IRQTM CLR1_IRQ0
Caution
If the above macros are used, the contents of the window register are destroyed. If an embedded macro instruction is used immediately before the above macro instructions, an "object error" occurs when the source file is assembled and then loaded to the in-circuit emulator. To use an embedded macro instruction immediately before the above macro instructions, insert a comment statement between them. Moreover, while either of the above macro instructions is executed, the other interrupt request cannot be acknowledged. For details, refer to 10.11 Notes on Using Interrupt.
74
PD17016, 17017
10.2.2 Configuration and function of interrupt permission flag (IPxxx) Each interrupt permission flag enables the interrupt of the corresponding peripheral hardware unit. So that an interrupt is acknowledged, all the following three conditions must be satisfied. * The interrupt must be enabled by the corresponding interrupt permission flag. * An interrupt request must be issued by the corresponding interrupt request flag. * The "EI" instruction (that enables all the interrupts) must be executed. Enabling or disabling an interrupt is controlled by a software macro. Table 10-2 lists the available software macros. These macros are defined in the device file and can be used by INCLUDEing the files supplied with the device file (D17016.INC for the PD17016 and D17017.INC for the PD17017) on the source program. Table 10-2. Software Macros Enabling/Disabling Interrupts
Function Enables timer interrupt Enables INT0 pin interrupt Enables timer interrupt and INT0 pin interrupt Disables timer interrupt Disables INT0 pin interrupt Disables timer interrupt and INTP0 pin interrupt Disables timer interrupt and enables INT0 pin interrupt Enables timer interrupt and disables INT0 pin interrupt Macro Format SET1_IPTM SET1_IP0 SET2_IPTM_IP0 CLR1_IPTM CLR1_IP0 CLR2_IPTM_IP0 INIT_NOT_IPTM_IP0 INIT_IPTM_NOT_IP0
Caution
If the above macros are used, the contents of the window register are destroyed. If an embedded macro instruction is used immediately before the above macro instructions, an "object error" occurs when the source file is assembled and then loaded to the in-circuit emulator. To use an embedded macro instruction immediately before the above macro instructions, insert a comment statement between them.
The status of the interrupt at reset is as follows: * On power-ON reset The interrupt is disabled. * On execution of clock stop instruction The interrupt is disabled. * On CE reset The interrupt is disabled. * In halt status The interrupt permission flag holds the previous status.
75
PD17016, 17017
10.2.3 Vector address generator (VAG) The vector address generator generates a branch address (vector address) of the program memory for the interrupt source acknowledged if a peripheral hardware interrupt has been acknowledged. Table 10-3 shows the vector address of each interrupt source. Table 10-3. Vector Address of Each Interrupt Source
Interrupt Source INT0 pin Timer Vector Address 05H 03H
76
PD17016, 17017
10.3 Interrupt Stack Register
10.3.1 Configuration and function of interrupt stack register Figure 10-2 shows the configuration of the interrupt stack register and the system register whose contents are saved to the interrupt stack register. The interrupt stack register saves the contents of the following system registers when an interrupt is acknowledged. * Bank register (BANK) * Index enable flag (IXE) When an interrupt is acknowledged and the contents of the above system registers are saved to the interrupt stack register, the contents of the above system registers are reset to "0". The interrupt stack register can save up to 4 levels of the contents of the above system registers. Therefore, up to four levels of multiple interrupts can be executed. The contents of the interrupt stack register are restored to the system registers when an interrupt return instruction ("RETI") is executed. Figure 10-2. Configuration of Interrupt Stack Register
Interrupt stack register (INTSK) Name Bit 0H 1H 2H 3H b3 - - - - Bank stack b2 - - - - b1 b0 b3 - - - - Status stack b2 - - - - b1 - - - - b0
Remark -: Bit not saved
77
PD17016, 17017
10.3.2 Interrupt stack register operation Figure 10-3 illustrates the operation of the interrupt stack register. If multiple interrupts exceeding 4 levels are acknowledged, the first saved contents are discarded and therefore, must be saved by program. Figure 10-3. Operation of Interrupt Stack Register (a) If interrupt does not exceed level 4
Undefined Undefined Undefined Undefined
A Undefined Undefined Undefined
B A Undefined Undefined
A Undefined Undefined Undefined
Undefined Undefined Undefined Undefined
VDD application Interrupt A
Interrupt B
RETI
RETI
(b) If interrupt exceeds level 4
A Undefined Undefined Undefined B A Undefined Undefined C B A Undefined D C B A E D C B D C B B C B B B
Interrupt A Interrupt B
Interrupt C
Interrupt D
Interrupt E
RETI
RETI
78
PD17016, 17017
10.4 Stack pointer, address stack register, and program counter
The address stack register saves the return address to which execution is to be returned from an interrupt processing routine. The stack pointer specifies the address of the address stack register. When an interrupt is acknowledged, therefore, the value of the stack pointer is decremented by one and the value of the program counter at that time is saved to the address stack register specified by the stack pointer. When the dedicated return instruction "RETI" is executed after the processing of the interrupt processing routine has been executed, the contents of the address stack register specified by the stack pointer are restored to the program counter, and the value of the stack pointer is incremented by one. For further information, also refer to 3. ADDRESS STACK (ASK).
10.5 Interrupt Enable Flip-Flop (INTE)
The interrupt enable flip-flop enables all the interrupts. When this flip-flop is set, all the interrupts are enabled. When it is reset, all the interrupts are disabled. This flip-flop is set or reset by using dedicated instructions "EI (to set)" and "DI (to reset)". The "EI" instruction sets this flip-flop when the instruction next to the "EI" instruction is executed, and the "DI" instruction resets the flip-flop while the "DI" instruction is executed. When an interrupt is acknowledged, this flip-flop is automatically reset. Nothing is affected even if the "DI" instruction is executed in the DI state, or if the "EI" instruction is executed in the EI state. This flip-flop is reset on power-ON reset, CE reset, and on execution of the clock stop instruction.
79
PD17016, 17017
10.6 Acknowledging Interrupts
10.6.1 Acknowledging interrupts and priority An interrupt is acknowledged in the following procedure: (1) Each peripheral hardware unit outputs an interrupt request signal to the corresponding interrupt control block if a given interrupt condition is satisfied (e.g., if a rising signal is input to the INT0 pin). (2) When the interrupt control block has received the interrupt request signal from the peripheral hardware unit, it sets the corresponding interrupt request flag (e.g., IRQ0 flag if the peripheral unit is the INT0 pin) to "1". (3) If the interrupt permission flag corresponding to the interrupt request flag (e.g., IP0 flag for IRQ0 flag) is set to "1" when the interrupt request flag is set to "1", the interrupt control block outputs "1". (4) The signal output by the interrupt control block is ANDed with the output of the interrupt enable flip-flop, and an interrupt acknowledge signal is output. This interrupt enable flip-flop is set to "1" by the "EI" instruction and reset to "0" by the "DI" instruction. If the interrupt control block outputs "1" while the interrupt enable flip-flop is "1", the interrupt is acknowledged. As shown in Figure 10-1, the interrupt acknowledge signal is input to each interrupt control block when the interrupt has been acknowledged. The interrupt request flag is reset to "0" by the signal input to the interrupt control block, and a vector address corresponding to the interrupt is output. If more than one interrupt block outputs "1" at this time, the interrupt acknowledge signal is not transferred to the next stage. If more than one interrupt request is issued at the same time, therefore, the interrupts are acknowledged in the following priority. INT0 pin > timer The interrupt of an interrupt source is not acknowledged unless the corresponding interrupt permission flag is set to "1". If the interrupt permission flag is reset to "0", therefore, an interrupt with a high hardware priority can be disabled.
80
PD17016, 17017
10.6.2 Timing chart for acknowledging interrupt Figure 10-4 shows the timing chart illustrating acknowledging interrupts. (1) in this figure illustrates how one interrupt is acknowledged. (a) in (1) shows the case where the interrupt request flag is lastly set to "1", and (b) in (1) shows the case where the interrupt permission flag is lastly set to "1". In either case, the interrupt is acknowledged when all the interrupt request flag, interrupt enable flip-flop, and interrupt permission flag are set to "1". If the last flag or flip-flop that was set to "1" satisfies the first instruction cycle of the "MOVT DBF, @AR" instruction or a given skip condition, the interrupt is acknowledged after the second instruction cycle of the "MOVT DBF, @AR" instruction or the instruction that is skipped (NOP) has been executed. The interrupt enable flip-flop is set in the instruction cycle next to the one in which the "EI" instruction is executed. (2) in Figure 10-4 illustrates how more than one interrupt is used. In this case, the interrupts are sequentially acknowledged according to the hardware priority if all the interrupt permission flags are set. The hardware priority can be changed by manipulating the interrupt permission flag by program. "Interrupt cycle" shown in Figure 10-4 is a special cycle in which the interrupt request flag is reset, a vector address is specified, and the contents of the program counter are saved after an interrupt has been acknowledged, and lasts for 4.44 s, which is equivalent to the execution time of one instruction. For further information, refer to 10.7 Operations after Interrupt Has Been Acknowledged.
81
PD17016, 17017
Figure 10-4. Timing Chart of Acknowledging Interrupt (1/3) (1) When one interrupt (e.g., rising of INT0 pin) is used (a) If interrupt is not masked by interrupt permission flag (IPxxx) <1> If "MOVT" instruction or normal instruction that satisfies skip condition is not executed when interrupt is acknowledged
Instruction Number of steps in macro EI SET1_IP0Note <3> <4> Normal instruction Interrupt cycle
INTE
INT0 pin
IRQ0 flag
IP0 flag
Instruction cycle: 4.44 s
Interrupt acknowledged Interrupt enable period Interrupt processing routine
Note
Software macro SET1_IP0 consists of four instructions. <2> If "MOVT" instruction or "instruction satisfying skip condition" is executed when interrupt is acknowledged
Instruction Number of steps in macro
EI
SET1_IP0Note <3> <4>
MOVT DBF,@AR Skip instruction
Interrupt cycle
INTE
INT0 pin
IRQ0 flag
IP0 flag
Interrupt acknowledged
Interrupt enable period
Interrupt processing routine
Note
Software macro SET1_IP0 consists of four instructions.
82
PD17016, 17017
Figure 10-4. Timing Chart of Acknowledging Interrupt (2/3) (b) If interrupt is kept pending by interrupt permission flag
Instruction Number of steps in macro SET1_IP0Note <2> <3> Interrupt cycle
EI
<4>
INTE
INT0 pin
IRQ0 flag
IP0 flag
Interrupt acknowledged Interrupt pending period Interrupt processing routine
Note
Software macro SET1_IP0 consists of four instructions.
83
PD17016, 17017
Figure 10-4. Timing Chart of Acknowledging Interrupt (3/3) (2) When two interrupts (INT0 pin and timer) are used (a) Hardware priority
Instruction Number of steps in macro INTE INT0 pin IRQ0 flag Timer interrupt IRQTM flag IP0 flag IPTM flag SET2_IPTM_IP0Note <2> <3> EI Interrupt cycle EI Interrupt cycle
INT0 pin interrupt acknowledged INT0 pin interrupt pending period
Timer interrupt acknowledged INT0 pin interrupt processing Timer interrupt processing
Timer interrupt pending period
Note
Software macro SET2_IPTM_IP0 consists of three instructions.
(b) Software priority
Instruction Number of steps in macro INTE INT0 pin IRQ0 flag Timer interrupt IRQTM flag IP0 flag IPTM flag SET1_IPTMNote <3> <4> Interrupt cycle SET1_IP0Note <3> <4> Interrupt cycle
EI
EI
Timer interrupt acknowledged Timer interrupt pending period Timer interrupt processing
INT0 interrupt acknowledged
INT0 pin interrupt pending period
INT0 pin interrupt processing
Note
Software macro SET1_IPTM, SET1_IP0 consists of four instructions.
84
PD17016, 17017
10.7 Operation After Interrupt Has been Acknowledged
When an interrupt has been acknowledged, the following processing is sequentially executed. (1) The interrupt enable flip-flop and the interrupt request flag corresponding to the acknowledged interrupt are reset to "0", disabling the interrupts. (2) The contents of the stack pointer are decremented by one. (3) The contents of the program counter are saved to the address stack register specified by the stack pointer. The contents saved at this time are the next program memory address that is used after the interrupt has been acknowledged. For example, if a branch instruction is executed, the contents saved are the branch destination address; if a subroutine call instruction is executed, they are the called address. Because the interrupt is acknowledged after the next instruction is executed as a "NOP" instruction if a skip condition is satisfied by a skip instruction, the saved contents are the skipped address. (4) The low-order 2 bits of the bank register (BANK) and the index enable flag (IXE) are saved to the interrupt stack. (5) The contents of the vector address generator corresponding to the acknowledged interrupt are transferred to the program counter. In other words, execution branches to an interrupt processing routine. The processing (1) through (5) above is executed in one special instruction cycle (4.44 s) in which the normal instruction is not executed. This instruction cycle is called an interrupt cycle. In other words, one instruction cycle time is necessary since an interrupt has been acknowledged until execution branches to the corresponding vector address.
10.8 Restoring from Interrupt Processing Routine
To restore execution from an interrupt processing routine to the processing that was being performed when the interrupt occurred, a dedicated instruction, "RETI", is used. When the "RETI" instruction is executed, the following processing is sequentially executed. (1) The contents of the address stack register specified by the stack pointer are saved to the program counter. (2) The contents of the interrupt stack are restored to the low-order 2 bits of the bank register (BANK) and index enable flag (IXE). (3) The contents of the stack pointer are incremented by one. The processing (1) through (3) above is executed in one instruction cycle in which the "RETI" instruction is executed. The difference between the "RETI" instruction and subroutine return instructions "RET" and "RETSK" is only the restoring operation of the bank register and index enable flag in (2) above.
85
PD17016, 17017
10.9 External (INT0 Pin) Interrupt
10.9.1 Outline of external interrupt Figure 10-5 outlines the external interrupt. As shown in the figure, the external interrupt issues an interrupt request at the rising edge of the signal input to the INT0 pin. The INT0 pin is a Schmitt trigger input pin to prevent malfunctioning due to noise, and does not accept a pulse less than 1 s wide. Figure 10-5. Outline of External Interrupt
Software macro SKT1_INT0 SKF1_INT0 Detects pin status
Interrupt control block
INT0 pin
Rising edge detection
IRQ0 flag
Schmitt trigger
10.9.2 Edge detection block The edge detection block detects the rising edge that issues the interrupt request of the INT0 pin.
86
PD17016, 17017
10.9.3 Pin status detection function The level of the signal input to the INT0 pin can be detected by using software macros. Therefore, the INT0 pin can be used as a 1-bit general-purpose input port when it is not used as an interrupt input pin. Table 10-4 shows the software macros. These macros are defined in the device file and can be used by INCLUDEing the file supplied with the device file (D17016.INC for the PD17016 and D17017.INC for the PD17017) on the source program. Table 10-4. Software Macros Detecting INT0 Pin Level
Function Skips next instruction if high level is input to INT0 pin Skips next instruction if low level is input to INT0 pin Macro Format SKT1_INT0 SKF1_INT0
Caution
If the above macros are used, the contents of the window register are destroyed. If an embedded macro instruction is used immediately before the above macro instructions, an "object error" occurs when the source file is assembled and then loaded to the in-circuit emulator. To use an embedded macro instruction immediately before the above macro instructions, insert a comment statement between them.
10.10 Internal Interrupt
The timer interrupt is used as the internal interrupt and can issue an interrupt request at fixed time intervals (refer to 11. TIMER FUNCTION).
87
PD17016, 17017
10.11 Notes on Using Interrupt
Other interrupts are not acknowledged while a software macro that resets an interrupt request is being executed. Example 1. Processing A ...... CLR1_IRQTM ...... Processing B ... Example 2. Processing A ...... CLR1_IRQ0 ...... Processing B ... Timer interrupt request is not acknowledged nor kept pending even if it is issued during this period. ... Interrupt request of INT0 pin is not acknowledged nor kept pending even if it is issued during this period. ...
88
PD17016, 17017
11. TIMER FUNCTION
The timer function is used for time management in developing a program.
11.1 Configuration of Timer
Figure 11-1 shows the configuration of the timer block. As shown in the figure, the timer consists of a timer carry block and a timer interrupt block. The clock generation circuit that sets the time of each timer divides the system clock by using clock select blocks A and B, and the timer mode select register (RF address 09H) of the control registers. The following subsections 11.1.1 and 11.1.2 respectively explain the configuration of the timer carry block and that of the timer interrupt block. Because the clock of each timer is created by dividing the system clock (4.5 MHz), if the frequency of the crystal resonator is not 4.5 MHz, the clock of each timer varies accordingly. 11.1.1 Configuration of timer carry block The timer carry block consists of clock select block A and timer carry FF block. 11.1.2 Configuration of timer interrupt block The timer interrupt block consists of clock select block B and interrupt control block. Figure 11-1. Configuration of Timer Block * Timer carry block
Control register
4.5 MHz
Clock select A
Timer carry FF
* Timer interrupt block
Control register
4.5 MHz
Clock select B
Interrupt control
Interrupt request signal
89
PD17016, 17017
11.2 Functional Outline of Timer
The timer can be used in two ways: by detecting the carry FF of the timer carry and by using the interrupt of the timer. The following subsections 11.2.1 and 11.2.2 respectively outline the functions of the timer carry and timer interrupt. 11.2.1 Functional outline of timer carry The timer carry manages time by detecting by program the status of the timer carry FF that is set at fixed intervals. Refer to 11.3 Timer Carry. 11.2.2 Functional outline of timer interrupt The timer interrupt manages time by issuing an interrupt request at fixed time intervals. Refer to 11.4 Timer Interrupt.
11.3 Timer Carry
11.3.1 Configuration of timer carry Figure 11-2 shows the configuration of the timer carry. As shown in the figure, the timer carry consists of a divider, selector, and timer carry FF block. Figure 11-2. Configuration of Timer Carry
Control register Name Timer mode select Address Bit Flag symbol b3 B T M 1 C K 1 09H b2 B T M 1 C K 0 b1 B T M 0 C K 1 b0 B T M 0 C K 0 b3 0 Timer carry FF judge 17H b2\ 0 b1 0 b0 B T M 0 C Y
Selector 250 ms 4.5 MHz Divider 100 ms 5 ms 1 ms Timer carry FF
90
PD17016, 17017
11.3.2 Function of timer carry The timer carry is set to 1 at the rising edge of the timer carry FF setting pulse that is set by the low-order 2 bits (BTM0CK1 and BTM0CK0 flags) of the timer mode select register. The content of the timer carry FF corresponds to the least significant bit (BTM0CY flag) of the timer carry FF judge register (RF address 17H) on a one-to-one basis. If the timer carry FF is set to "1", therefore, the BTM0CY flag is also set to "1". The BTM0CY flag is reset to "0" when data is written to the window register by the "PEEK" instruction (Read & Reset). When the BTM0CY flag is reset to "0", the timer carry FF is also reset to "0". Therefore, a timer that is set via the timer mode select register can be used by reading the contents of the BTM0CY flag by program. When using the timer carry, note the following. Caution The timer carry is disabled from being set on application of the supply voltage VDD (on powerON reset), and is not set to "1" until the content of the BTM0CY flag is once read by the "PEEK" instruction. This means that "0" is always read from the BTM0CY flag immediately after power-ON reset, and that the flag is set to "1" at time intervals set by the timer mode select register. The timer carry also controls the timing of the reset operation by the CE pin (CE reset). If the CE pin goes high, CE reset is effected in synchronization with the timing that sets the timer carry FF to "1". Therefore, a power failure can be detected by reading the content of the BTM0CY flag at system reset (powerON reset and CE reset). For details, refer to 11.3.7 Notes on using timer carry. Because the BTM0CY flag is a read-only flag, the device operation is not affected in any way even if data is written to this flag by using the "POKE" instruction. However, an error occurs if the 17K Series assembler is used. For details, refer to 8.4 Notes on Using Register File.
91
PD17016, 17017
11.3.3 Configuration and function of timer mode select register The timer mode select register sets the time interval of the timer carry and the timer interrupt of the internal timer. These two time intervals can be set independently. Figure 11-3 shows the waveform of a timer time setting pulse.
Name b3 Timer mode select register B T M 1 C K 1
Flag symbol b2 B T M 1 C K 0 b1 B T M 0 C K 1 b0 B T M 0 C K 0
Address
Read/ Write
09H
R/W
Sets time interval at which timer carry is set 0 0 1 1 0 1 0 1 100 ms 250 ms 5 ms 1 ms
Sets time interval at which timer interrupt is set Note 0 0 1 1 0 1 0 1 100 ms 250 ms 5 ms 1 ms
On reset
Power-ON Clock stop CE reset
0 0
0 0
0 0
0 0
Holds status
Note
For the details on the timer interrupt, refer to 11.4 Timer Interrupt.
92
PD17016, 17017
Figure 11-3. Waveform of Timer Time Setting Pulse
1 kHz 0.33 ms 1 ms 0.67 ms
200 Hz 2 ms 5 ms 3 ms
10 Hz 50 ms 100 ms 50 ms
4 Hz 100 ms 250 ms 150 ms
93
PD17016, 17017
11.3.4 Configuration and function of timer carry FF judge register The timer carry FF judge register detects the status of the timer carry FF of the internal timer. configuration and function of this register are illustrated below.
Name b3 Timer carry FF judge register 0 Flag symbol b2 0 b1 0 b0 B T M 0 C Y 17H Address Read/ Write R & Reset
The
Detects status of timer carry FF 0 1 Timer carry FF is not set Timer carry FF is set
Fixed to "0"
On reset
Power-ON Clock stop CE reset
0
0
0
0 1 1
The BTM0CY flag is set to "1" at time intervals set by the timer mode select register. The BTM0CY flag is detected by the "PEEK" instruction via the window register. If the BTM0CY flag is set to "1" at this time, the value of the flag is transferred to the window register, and then the BTM0CY flag is reset to "0" (Read & Reset). The BTM0CY flag is "0" on power-ON reset, but "1" on CE reset (including CE reset that is executed in the clock stop status); therefore, it can be used as a power failure detection flag. The BTM0CY flag is not set to "1" until it is read once by the "PEEK" instruction after power-ON reset. Once the "PEEK" instruction has been executed, it is set to "1" at the time interval set by the timer mode select register.
94
PD17016, 17017
11.3.5 Example of using timer with BTM0CY flag Here is an example program. Example M1 MEM 0.10H ; 1-second counter ; Embedded macro ; Sets set time of timer carry FF to 250 ms LOOP: SKT1 BR ADD SKT1 BR BTM0CY NEXT M1, #0100B CY NEXT ; Adds 4 to data memory M1 ; Embedded macro ; Tests CY flag and, ; if "0", branches to NEXT ; if "1", executes processing A Processing A NEXT Processing B BR LOOP ; Executes processing B and branches to LOOP ; Embedded macro ; Tests BTM0CY flag; if "0", branches to NEXT
INITFLG NOT BTM0CK1, BTM0CK0
This program executes processing A every 1 second. In developing a program, the following point must be noted. Caution Keep the time interval at which the BTM0CY flag is detected shorter than the time interval at which the timer carry FF is set to 1. This is because, in the above example, if the execution time of processing B is longer than 250 ms, setting of the timer carry FF is not detected. Figure 11-4. Detection of BTM0CY Flag and Timer Carry FF
Timer carry FF setting pulse H L <1> 1 BTM0CY flag 0 SKT1 BTM0CY SKT1 BTM0CY
Processing B'
<2>
<3>
<4>
<5>
SKT1 BTM0CY
Processing B
Because the execution time of processing B' is long, after the BTM0CY flag set in <2> has been detected, the status of BTM0CY flag that is set in <3> is not detected.
95
PD17016, 17017
11.3.6 Error of timer caused by BTM0CY flag The error of the timer caused by the BTM0CY flag includes an error caused by the detection time of the BTM0CY flag and an error that occurs when the set time of the timer carry FF is changed. (1) Error caused by detection time of BTM0CY flag As explained in 11.3.5, the time interval at which the BTM0CY flag is detected must be shorter than the time interval at which the timer carry FF is set to 1. Where the time interval at which the BTM0CY flag is detected is tCHECK and the time interval at which the timer carry FF is set is tSET (250, 100, 5, or 1 ms), the following relation must be satisfied. tCHECK < tSET The error of the timer when the BTM0CY flag is detected as shown in Figure 11-5 is as follows. 0 < error < tCHECK Figure 11-5. Error Caused by Detection Time of BTM0CY Flag
H L 1 BTM0CY flag 0 tCHECK1 SKT1 BTM0CY <1> tCHECK2 tCHECK3 SKT1 BTM0CY <4> SKT1 BTM0CY <2> SKT1 BTM0CY <3> tSET
Timer carry FF setting pulse
As shown in Figure 11-5, the timer is updated when the BTM0CY flag is detected in <2> because it is "1". When the flag is 0 when it is detected in <3> next. Therefore, the timer is not updated until the flag is detected again in <4>. At this time, the time of the timer is prolonged by the time of tCHECK3.
96
PD17016, 17017
(2) Error when changing set time of timer carry FF The set time of the timer carry FF is set by the BTM0CK1 and BTM0CK0 flags of the timer mode select register. Four types of timer time setting pulses, 1 kHz, 200 Hz, 10 Hz, and 4 Hz, can be selected as shown in Figures 11-2 and 11-3. These four pulses operate independently. If the timer time setting pulse is changed by using the BTM0CK1 and BTM0CK0 flags, an error occurs as shown in the following example. Example ;<1> INITFLG BTM0CK1, NOT BMT0CK0 ; Embedded macro ; Sets timer carry FF setting pulse to ; 200 Hz (5 ms) Processing A ;<2> SET2 BTM0CK1, BTM0CK0 ; Embedded macro ; Sets timer carry FF setting pulse to ; 1 kHz (1 ms) Processing A ;<3> INITFLG BTM0CK1, NOT BTM0CK0 ; Embedded macro ; Sets timer carry FF setting pulse to ; 200 Hz (5 ms) The timer carry FF setting pulse is changed as follows at this time.
Internal pulse 200Hz Internal pulse 1 kHz Timer carry FF setting pulse H L H L H L <1> 1 BTM0CY flag 0 SKT1 BTM0CY
Instruction of <2> Instruction of <3>
When the set time of the timer carry FF is changed as shown above, the BTM0CY flag holds the previous status (<2> in the figure) if the changed pulse falls, but is set to 1 (<3> in the figure) if the pulse rises.
97
PD17016, 17017
In the previous example, the timer time setting pulse is changed between 200 Hz (5 ms) and 1 kHz (1 ms). The same applies when the pulse is changed between 4 Hz (250 ms) and 10 Hz (100 ms). Therefore, an error until the BTM0CY flag is set first when the timer carry FF setting time is changed as shown in Figure 11-6 is as follows. -tSET < error < tCHECK where, tSET tCHECK : new timer carry FF setting time : time to detect BTM0CY flag
The internal pulses of 4 Hz, 10 Hz, 200 Hz, and 1 kHz have a phase difference. This phase difference is included in the above error because it is shorter than the time of the new pulse. For the phase difference of each pulse, refer to 11.4.5 Notes on using timer interrupt. Figure 11-6. Error When Timer Carry FF Setting Time Is Changed from A to B
<1> Error of -tSET H Internal pulse A L H Internal pulse B L Timer carry FF setting pulse BTM0CY flag 0 SKT1 BTM0CY ** a=0 a ** a=0 a tCHECK H L 1 tSET tSET <2> Error of tCHECK
Original timer time Actual timer time Time changed Error is -tSET because BTM0CY flag is "1" if it is detected immediately after timer time has been changed.
Actual timer time Original timer time Time changed Error is tCHECK because BTM0CY flag is reset once if timer time is changed immediately after BTM0CY flag has been detected.
98
PD17016, 17017
11.3.7 Notes on using timer carry The timer carry is also used as a reset synchronization signal when reset is effected by the CE pin (CE reset), not only for the timer function. The CE reset is effected if the timer carry FF setting pulse rises the next time after the CE pin has gone high. At this time, the following points must be noted. (1) The sum of the timer updating processing time and the BTM0CY flag detection time must be shorter than the timer carry FF setting time. (2) If a program is created in which the timer always operates at a fixed interval regardless of CE reset after application of the supply voltage (power-ON reset), correction must be made each time CE reset is effected. (3) Detection of the BTM0CY flag takes precedence over the reset synchronization signal on CE reset. If these two coincide, therefore, CE reset is delayed once. (1) through (3) above are explained in more detail in the following (a) through (c).
99
PD17016, 17017
(a) Timer updating processing time and detection time interval of BTM0CY flag As explained in 11.3.6, the time interval tSET at which the BTM0CY flag is detected must be shorter than the time interval at which the timer carry FF is set. If the updating processing time of the timer is long even if the time interval to detect the BTM0CY flag is short, the timer processing may not be executed normally if CE reset is effected. Therefore, the following condition must be satisfied. tCHECK + tTIMER < tSET where, tCHECK : time interval to detect BTM0CY flag tTIMER : timer updating processing time tSET Here is an example. Example Example of timer updating processing and BTM0CY flag detection time interval START: CLR2 ; Program address 0000H BTM0CK1, BTM0CK0 ; Embedded macro ; Sets set time of timer carry FF to 100 ms TIMER: ;<1> SKT1 BTM0CY BR AAA ; Embedded macro ; Tests BTM0CY flag; if "0", branches to AAA : time to set timer carry FF
Timer update BR AAA: Processing A BR TIMER TIMER
The timing chart of the above program is shown below.
H CE pin Timer carry FF setting pulse BTM0CY flag L H L 1 0 BTM0CY detection interval tCHECK SKT1 BTM0CY SKT1 BTM0CY Timer updating processing tTIMER If this processing time is long, CE reset is effected while processing is in progress. CE reset
100
PD17016, 17017
(b) Correction of timer carry on CE reset An example of correcting the timer at CE reset is shown below. As shown in this example, the timer must be corrected on CE reset if "the timer carry is used to detect a power failure and the timer carry is also used as a watch timer". The timer carry is reset to "0" on first power application (power-ON reset), and afterward, is disabled from being set until the BTM0CY flag is read once by the "PEEK" instruction. If the CE pin goes high, CE reset is effected in synchronization with the rising edge of the timer carry FF setting pulse. At this time, the BTM0CY flag is set to "1" and the program is started. Therefore, it is judged that power-ON reset has been effected if the BTM0CY flag is "0" and that CE reset has been effected if the BTM0CY flag is "1", by detecting the status of the BTM0CY flag on system reset (power-ON reset or CE reset). A power failure can be detected in this way. At this time, the watch timer must continue operating even on CE reset. However, because the BTM0CY flag is reset to "0" when the flag is read to detect a power failure, the set "1" status of the BTM0CY flag is overlooked once. Therefore, the watch timer must be updated if it is judged by means of power failure detection that CE reset has been effected. For the details on power failure detection, refer to 13.6 Power Failure Detection. Example Example of correcting timer on CE reset (to detect power failure and update watch by timer carry) START: Processing A ;<1> SKT1 BR BACKUP: ;<2> ; Program address 0000H
BTM0CY INITIAL
; Embedded macro ; Tests BTM0CY flag; ; if "0", branches to INITIAL (power failure detection)
Updates watch by 100 ms LOOP: ;<3> Processing B SKF1 BR BR INITIAL: CLR2 BTM0CY BACKUP LOOP
; Updates watch because back up (CE reset) is ; performed
; While performing processing B, ; tests BTM0CY flag and updates watch
BTM0CK1, BTM0CK0 ; Embedded macro ; Because power failure (power-ON reset) occurs, sets ; set time of timer carry FF to 100 ms, and executes ; processing C Processing C LOOP
BR
Figure 11-7 shows the timing chart of the above program.
101
PD17016, 17017
Figure 11-7. Timing Chart
VDD CE Internal pulse 10 Hz Timer carry FF setting pulse BTM0CY flag Program processing Program instruction 5V 0V H L H L H L 1 0 A <1> C <3> B <3> Updates watch B <3> B <3> B B <3> <3> B B <3> <3> Updates watch B B B A <1> B B <3> <3> Updates watch B
<3> <3>
Applocation of Power-ON reset supply voltage Program starts from address 0
Updates watch
Updates watch CE reset Program starts from address 0.
BTM0CY flag detection
Watch is updated because BTM0CY flag is set (1) Point B Point C Point D Point E
Point A
As shown in Figure 11-7, the program is started from address 0000H at the rising edge of the internal 10-MHz pulse when supply voltage VDD is applied first. When the BTM0CY flag is detected at point A, the BTM0CY flag is reset to "0" because power has been just applied, and it is judged that a power failure (power-ON reset) has occurred. Therefore, "processing C" is executed and the timer carry FF setting pulse is set to 100 ms. Because the contents of the BTM0CY flag are read once at point A, the BTM0CY flag is set to "1" every 100 ms. Next, the program counts up the watch while executing "processing B" even if the CE pin goes low at point B and high at point C, unless the clock stop instruction is executed. Because the CE pin goes high at point C, CE reset is effected at point D where the pulse for setting the next timer carry FF rises and the program is started from address 0000H. Because the BTM0CY flag is set to "1" when it is detected at point E at this time, it is judged that back up (CE reset) has been performed. As is evident from the figure, the watch is delayed by 100 ms each time CE reset is effected unless the watch is updated by 100 ms at point E. If processing A takes longer than 100 ms when a power failure is detected at point E, setting of the BTM0CY flag is overlooked two times; therefore, processing A must be completed in less than 100 ms. The same applies when the timer carry FF setting pulse is set to 250, 5, or 1 ms. Therefore, the BTM0CY flag must be detected to detect a power failure within the timer carry FF setting time after the program has started from address 0000H.
102
PD17016, 17017
(c) If BTM0CY flag is detected at same time as CE reset As explained in (b), CE reset is effected if the BTM0CY flag is set to "1". If an instruction that reads the BTM0CY flag happens to be executed at the same time as CE reset, execution of the instruction that reads the BTM0CY flag takes precedence. Therefore, if the next setting of the BTM0CY flag (rising of the timer carry FF setting pulse) after the CE pin has gone high is performed at the same time as the instruction that reads the BTM0CY flag, CE reset is effected "when the BTM0CY flag is set next". This operation is illustrated in Figure 11-8. Figure 11-8. Operation When CE Reset Is Executed At Same Time As Instruction That Reads BTM0CY Flag
H L Timer carry FF H setting pulse L 1 BTM0CY flag 0 SKT1 BTM0CY Timer carry FF setting pulse BTM0CY flag Instruction H L 1 0 SKT 1 BTM0CY (PEEK *** ) (SKT *** ) SKT1 BTM0CY CE reset CE pin
Embedded macro PEEK WR,. MF. BTM0CY SHR4 SKT WR, #. DF. BTM0CY AND 000 FH 4.44 s If BTM0CY flag is read during this period, CE reset is delayed once. Program is supposed to start from address 0000H at this time, but CE reset is not effected because program that reads BTM0CY takes precedence.
Therefore, a program that periodically detects the BTM0CY flag never executes a CE reset if the detection interval of the BTM0CY flag is the same as the setting time of the TMCY flag. This must be prevented as follows. Because one instruction cycle is 4.44 s (1/225 kHz), a program, for example, that detects the BTM0CY flag once every 255 instructions reads the BTM0CY flag every 1 ms = 4.44 s x 225. Once detection and setting of the BTM0CY flag coincide, CE reset is never effected no matter which of 1, 5, 100, or 250 ms of the timer time setting pulse is selected. Therefore, do not develop a program that has a cycle satisfying the following condition.
tSET x 225 X where,
= n (n: natural number)
tSET : setting time of BTM0CY flag X : period x number of steps of instruction that reads BTM0CY flag
An example of a program that satisfies this condition is shown below. Do not develop such a program.
103
PD17016, 17017
Example Processing A SET2 BTM0CK1, BTM0CK0 ; Embedded macro ; Timer carry FF setting pulse is set to 1 ms LOOP: ;<1> SKT1 BR AAA: 221 steps BR BBB: 221 steps BR LOOP LOOP BTM0CY BBB ; Embedded macro
In this example, the instruction <1> that reads the BTM0CY flag is repeatedly executed every 225 instructions. If the BTM0CY flag is set at the timing of the instruction <1>, therefore, CE reset is not effected.
104
PD17016, 17017
11.4 Timer Interrupt
11.4.1 Configuration of timer interrupt Figure 11-9 shows the configuration of the timer interrupt. As shown in the figure, the timer interrupt consists of a divider, selector, and interrupt control flag. Figure 11-9. Configuration of Timer Interrupt
Control register Name Timer mode select Address Bit Flag symbol b3 B T M 1 C K 1 09H b2 B T M 1 C K 0 b1 B T M 0 C K 1 b0 B T M 0 C K 0
Selector 250 ms 4.5 MHz Divider 100 ms 5 ms 1 ms
IPTM flag IRQTM flag
Issuance of interrupt request
Remark The interrupt permission flag (IPTM) is set by a software macro. The interrupt request flag (IRQTM) can be reset by software. For details, refer to 10. INTERRUPT.
105
PD17016, 17017
11.4.2 Function of timer interrupt The timer interrupt request is issued at the falling edge of a timer interrupt pulse set by the high-order 2 bits (BTM1CK1 and BTM1CK0 flags) of the timer mode select register (refer to 11.3.3). The timer interrupt request corresponds to the IRQTM flag on a one-to-one basis. When the timer interrupt request is issued, the IRQTM flag is set to "1". In other words, the IRQTM flag is set to "1" if the timer interrupt pulse falls. So that the timer interrupt is acknowledged, the "EI" instruction that enables all the interrupts must be executed and the timer interrupt must be enabled, in addition to issuance of the interrupt request as explained in 10. Interrupt. The timer interrupt is enabled by setting the IPTM flag to "1". Therefore, the timer interrupt is acknowledged if the IRQTM flag is set to "1" when the "EI" instruction is executed and the IPTM flag is set to "1". The IPTM flag is set by a software macro. For the macro that enables or disables an interrupt, refer to Table 10-2. Software Macros Enabling/Disabling Interrupts. The IRQTM flag cannot be set by software. When the timer interrupt is acknowledged, the program execution branches to program memory address 0003H. The IRQTM flag is reset to "0" as soon as the interrupt has been acknowledged. Figure 11-10 shows the relation between the timer interrupt pulse and IRQTM flag. Figure 11-10. Relation between Timer Interrupt Pulse and IRQTM Flag
Timer interrupt pulse IRQTM IPTM INTE FF H L 1 0 1 0 EI DI
<1>
Acknowledging timer interrupt and interrupt processing Timer interrupt is acknowledged as soon as IPTM flag is set, and interrupt processing is executed
IRQTM flag is set at falling edge of timer interrupt pulse
Interrupt is not acknowledged even if EI instruction is executed because IPTM flag is not set Interrupt enable period
Interrupt pending period
A point to be noted is that, as shown in point <1> in the above figure, the timer interrupt is acknowledged when the "EI" instruction is executed next and the IPTM flag is set once the IRQTM flag has been set when the timer interrupt is disabled by the "DI" instruction or IPTM flag. In this case, the interrupt request can be cleared by executing a software macro that resets the interrupt request (refer to Table 10-1. Software Macros That Reset Interrupt Requests). One level of the stack is used when the timer interrupt is acknowledged. At this time, the contents of the register bank (BANK: address 79H) and the content of the index enable flag (IXE: bit 0 of address 7FH) are automatically saved. To return from the interrupt processing routine, use a dedicated instruction "RETI". For details, refer to 3. ADDRESS STACK (ASK) and 10. INTERRUPT. The following subsections 11.4.3 and 11.4.4 explain an example of using the timer interrupt and an error of the timer interrupt. For the relation between the timer interrupt and the other interrupt (INT0 pin), refer to 10. INTERRUPT.
106
PD17016, 17017
11.4.3 Example of using timer with timer interrupt Example M1 TIMER MEM DAT BR ORG TIMER ADD SKT1 BR CY EI_RETI 0.10H 0003H START ; 80-ms counter ; Symbol definition of timer interrupt vector address ; Branches to START ; Program address (0003H) M1, #0001B ; Adds 1 to M1 ; Tests CY flag ; Return if carry does not occur
Processing A EI_RETI: EI RETI START: INITFLG BTM1CK1, NOT BTM1CK0 ; Embedded macro ; Sets timer interrupt pulse to 5 ms MOV EI LOOP: Processing B BR LOOP M1, #0000B ; Clears contents of M1 ; Enables timer interrupt (software macro) ; Enables all interrupts SET1_IPTM
The above program executes processing A every 80 ms. The points to be noted at this time are that the DI status is automatically set when the interrupt is acknowledged, and that the IRQTM flag is set to "1" even in the DI status. If processing A takes longer than 5 ms, therefore, the interrupt is acknowledged even if the "RETI" instruction is executed. Consequently, processing B is not executed.
107
PD17016, 17017
11.4.4 Error of timer interrupt As explained in 11.4.2, the timer interrupt is acknowledged each time the timer interrupt pulse falls if the EI instruction is executed and the timer interrupt is enabled. Therefore, an error of the timer when the timer interrupt is used occurs only in the following cases (1) through (3). (1) When the first interrupt is acknowledged with the timer interrupt enabled (2) When the first interrupt is acknowledged with the time of the timer interrupt pulse changed (3) If the software macro that resets the timer interrupt request is executed at the same time as the falling of the timer interrupt pulse (the interrupt is not acknowledged) Figure 11-11 shows the errors that may occur in each of the above cases. Figure 11-11. Error of Timer Interrupt (1/2) (a) When timer interrupt is enabled
Timer interrupt pulse IRQTM IPTM INTE FF H L 1 0 1 0 EI DI tSET
EI Interrupt pending
EI EI <3> Interrupt acknowledged Interrupt acknowledged
<1><2> SET1_IPTM Interrupt acknowledged
At point <1> in the above figure, the timer interrupt is acknowledged immediately if the interrupt is enabled by setting the IPTM flag. At this time, the error is -tSET. If the interrupt is enabled by the "EI" instruction at point <2>, the interrupt occurs at the falling edge of the timer interrupt pulse at point <3>. At this time, the error is -tSET < error < 0.
108
PD17016, 17017
Figure 11-11. Error of Timer Interrupt (2/2) (b) If timer interrupt pulse is changed
Internal pulse A Internal pulse B H L H
L Timer interrupt H pulse L 1 IRQTM 0 1 IPTM 0 EI INTE FF DI EI Interrupt acknowledged EI EI EI <2>Interrupt <3> Timer interrupt pulse acknowledged changed <1> Timer interrupt pulse changed EI Interrupt acknowledged
Because the timer interrupt pulse does not fall even if the timer interrupt pulse is changed to B at point <1>, the interrupt is acknowledged at the next point <2>. If the timer interrupt pulse is changed to A at point <3>, the timer interrupt pulse falls, and the interrupt is immediately acknowledged.
109
PD17016, 17017
11.4.5 Notes on using timer interrupt When developing a program in which the timer always operates after the supply voltage VDD has been once applied (power-ON reset) by using the timer interrupt, such as a watch program, the timer interrupt processing must be completed within specific time. Take the following program for example. Example M1 TIMER MEM DAT BR ORG TIMER ADD SKT1 BR ;<1> Watch processing EI_RETI: EI RETI START: INITFLG NOT BTM1CK1, BTM1CK0, NOT BTM0CK1, NOT BTM0CK0 ; Embedded macro ; Sets timer interrupt time to 250 ms and timer carry FF ; setting time to 100 ms SET1_IPTM EI LOOP: Processing A BR LOOP ; Enables timer interrupt (software macro) ; Enables all interrupts M1, #0100B CY EI_RETI 0.10H 0003H START ; 1-ms counter ; Symbol definition of interrupt vector address ; Branches to START ; Program address (0003H) ; Adds 0100B to contents of M1 ; Watch processing if carry occurs ; Return if carry does not occur
In this example, watch processing <1> is executed every 1 second while processing A is executed. If the CE pin goes high, CE reset is effected in synchronization with the rising of the timer carry FF setting pulse, as shown in Figure 11-12 (a). If the timer interrupt request (IRQTM flag) is issued at the same time as setting of the timer carry FF, CE reset takes precedence. When CE reset is effected, the IRQTM flag is automatically reset to "0". In other words, timer processing is not executed once if the CE reset is effected while the IRQTM flag is set to "1".
110
PD17016, 17017
To prevent this, a delay time is provided between "rising of the timer carry FF setting pulse" and "falling of the timer interrupt pulse" as shown in Figure 11-12(b). In the above example, the timer interrupt is not overlooked even if the CE reset is effected if the watch processing is executed within 10 ms as shown in Figure 11-12(b). Because the timer carry FF and timer interrupt time setting pulse can be set to 4 Hz (250 ms), 10 Hz (100 ms), 200 Hz (5 ms), or 1 kHz (1 ms) independently, time differences shown in Figure 11-13 and Table 11-1 are provided. To validate the timer interrupt at CE reset, therefore, the processing of the timer interrupt must be completed within the delay time of the pulse as shown in Figure 11-13. Figure 11-12. Timing Chart (a)
CE pin Timer carry FF setting pulse Timer interrupt pulse H L H L H L Timer interrupt CE reset is effected at this point and timer interrupt is overlooked once because timer carry FF setting pulse rises.
(b)
CE pin Timer carry FF setting pulse Timer interrupt pulse H L H L H L Timer interrupt Timer interrupt Delay time (10 ms in this case)
CE reset Because falling of timer interrupt pulse and rising of timer carry FF setting pulse are delayed for 10 ms, timer processing is executed normally even if CE reset is effected if timer interrupt processing is completed within 10 ms
111
PD17016, 17017
Figure 11-13. Time Difference between Timer Carry FF Setting Pulse and Timer Interrupt Pulse
1 ms BTM0CY 2:1:1 1 ms INT 5 ms BTM0CY 5 ms INT 1 ms
Dummy 10 ms 100 ms BTM0CY 100 ms INT 250 ms BTM0CY 250 ms INT
112
PD17016, 17017
Table 11-1. Time Difference between Rising Edge of Timer Carry FF Pulse and Falling Edge of Timer Interrupt Pulse
Internal Pulse Minimum Value of Time Difference (Refer to figure below.) t1 666 s 333 s 333 s 333 s 333 s 3 ms 2 ms 2 ms 333 s 1 ms 50 ms 10 ms 333 s 1 ms 40 ms 100 ms t2 333 s 666 s 666 s 666 s 666 s 2 ms 3 ms 3 ms 666 s 4 ms 50 ms 40 ms 666 s 4 ms 10 ms 150 ms
Timer carry 1 ms 1 ms 1 ms 1 ms 5 ms 5 ms 5 ms 5 ms 100 ms 100 ms 100 ms 100 ms 250 ms 250 ms 250 ms 250 ms Timer carry FF setting pulse Timer interrupt pulse H L H L
Timer interrupt 1 ms 5 ms 100 ms 250 ms 1 ms 5 ms 100 ms 250 ms 1 ms 5 ms 100 ms 250 ms 1 ms 5 ms 100 ms 250 ms
t1
t2
113
PD17016, 17017
12. STANDBY
The standby function is used to reduce the current consumption of the device during back up.
12.1 Configuration of Standby Block
Figure 12-1 shows the configuration of the standby block. As shown in the figure, the standby block is divided into two blocks: halt control block and clock stop control block. The halt control block consists of a halt control circuit, interrupt control block, timer carry, and key input pins P0D0/ADC2 through P0D3/ADC5, and controls the operation of the CPU (program counter, instruction decoder, and ALU block). The clock stop control block controls the 4.5-MHz crystal oscillation circuit, CPU, system register, and control registers, by using the clock stop control circuit. Figure 12-1. Configuration of Standby Block
Halt block Interrupt block Timer carry P0D3/ADC5 pin P0D2/ADC4 pin P0D1/ADC3 pin P0D0/ADC2 pin Input latch Halt control circuit HALT h
CPU Program counter (PC) Instruction decoder ALU
Clock stop block CE pin XOUT pin
Clock stop control circuit STOP s
System register Control register
XIN pin
Internal block
114
PD17016, 17017
12.2 Standby Function
The standby function reduces the current consumption of the device by stopping some or all the operations of the device. The standby function can be used in two modes: halt and clock stop. The halt mode is to reduce the current consumption of the device by executing a dedicated instruction "HALT h" and stopping the operation of the CPU. The clock stop mode is to reduce the current consumption of the device by executing a dedicated instruction "STOP s" and stopping the 4.5-MHz crystal oscillation circuit. In addition to the halt and clock stop modes, the operation mode of the device can be also set by the CE pin. The CE pin is used to control the operation of the PLL frequency synthesizer and reset the device, and can be said to be a type of the standby function in that it controls the operation of the PLL frequency synthesizer. The following section 12.3 explains how to set the operation mode of the device by using the CE pin. Sections 12.4 and 12.5 respectively explain the halt and clock stop modes.
12.3 Selecting Device Operation Mode with CE Pin
The CE pin controls the following functions (1) through (3) by using the level and rising edge of an externally input signal. (1) Controls operation of PLL frequency synthesizer (2) Enables or disables clock stop instruction (3) Resets device 12.3.1 Controlling operation of PLL frequency synthesizer The PLL frequency synthesizer can operate only when the CE pin is high. The PLL frequency synthesizer is automatically disabled when the CE pin is low. At this time, the VCOH and VCOL pins are internally pulled down, and the EO0 and EO1 pins are floated. The PLL frequency synthesizer can be disabled by program at any time when the CE pin is high. 12.3.2 Enabling and disabling clock stop instruction The clock stop instruction "STOP s" is enabled only when the CE pin is low. The "STOP s" instruction is executed as a no-operation (NOP) instruction if it is executed when the CE pin is high. 12.3.3 Resetting device The device can be reset (CE reset) by raising the CE pin. The device can also be reset through power application (power-ON reset). For details, refer to 13. RESET.
115
PD17016, 17017
12.3.4 Inputting signal to CE pin The CE pin does not accept a low or high level of less than 110 to 165 s to prevent malfunctioning due to noise. The level of the signal input to the CE pin can be detected by using the CE flag of the CE pin level judge register (RF address 07H). Figure 12-2 shows the relation between the input signal and CE flag. Figure 12-2. Relation between Signal Input to CE Pin and CE Flag
H L 1 CE flag 0 CE pin Less than 110 to 165 s 110-165 s Less than 110 to 165 s 110-165 s CE reset PLL disabled STOP s instruction enabled (NOP) CE reset is executed in synchronization with next setting of timer carry FF
PLL operation enabled STOP s instruction disabled (NOP)
PLL disabled STOP s instruction enabled
12.3.5 Configuration and function of CE pin level judge register The CE pin level judge register detects the level of the signal input to the CE pin. The configuration and function of this register are illustrated below.
Name b3 CE pin level judge register 0
Flag symbol b2 0 b1 0 b0 C E
Address
Read/ Write
07H
R
Detects level input to CE pin 0 1 Low level High level
Fixed to "0"
On reset
Power-ON Clock stop CE reset
0
0
0
- - -
- : Determined depending on pin status
The CE flag is not affected by a low or high level of less than 110 to 165 s.
116
PD17016, 17017
12.4 Halt Function
The halt function stops the operation clock of the CPU by executing the "HALT h" instruction. When the "HALT h" instruction is executed, the program stops at the "HALT h" instruction, until the halt status is released later. Therefore, the current consumption of the device can be reduced in the halt status by the operating current of the CPU. The halt status can be released by key input, timer carry, or interrupt. The releasing condition of the key input, timer carry, and interrupt is specified by the operand "h" of the "HALT h" instruction. The "HALT h" instruction is valid regardless of the input level of the CE pin. The following subsections 12.4.1 through 12.4.6 explain the halt status, halt release condition, and each halt release condition. 12.4.1 Halt status All the operations of the CPU are stopped in the halt status. In other words, program execution is stopped at the "HALT h" instruction. However, the peripheral hardware units continue the operations set before the "HALT h" instruction is executed. For the operations of the peripheral hardware units, refer to 12.6 Device Operations in Halt and Clock Stop Status.
117
PD17016, 17017
12.4.2 Halt release condition Figure 12-3 shows the halt release conditions. As shown in this figure, the halt release conditions are set by 4-bit data specified by operand "h" of the "HALT h" instruction. The halt status is released when the condition specified as "1" by operand "h" is satisfied. When the halt status is released, the execution starts from the instruction next to the "HALT h" instruction. If two or more release conditions are specified, and if any one of the specified conditions is satisfied, the halt condition is released. If the device is reset (power-ON reset or CE reset), the halt status is released, and each reset operation is performed. If 0000B is set as the halt release condition "h", no release condition is set. At this time, the halt status is released if the device is reset (power-ON reset or CE reset). The following subsections 12.4.3 through 12.4.5 explains halt release conditions set by key input, timer carry, and interrupt. 12.4.6 shows an example when two or more release conditions are specified. Figure 12-3. Halt Release Condition
HALT h (4 bits) Operand bit b3 b2 b1 b0
Sets halt release condition Releases if high level is input to P0D pin (P0D3/ADC5-P0D0/ADC2) Releases if timer carry FF is set to "1" Undefined (fixed to "0") Releases if interrupt (INT0 pin or timer) is acknowledged 0 1 Does not release even if condition is satisfied Releases if condition is satisfied
118
PD17016, 17017
12.4.3 Releasing halt status by key input Releasing the halt status by key input is specified by the "HALT 0001B" instruction. If releasing the halt status by key input is specified, the halt status is released when a high level is input to any of the four pins P0D0/ADC2 through P0D3/ADC5. The following paragraphs (1) through (4) explain the points to be noted when using a general-purpose output port for a key source signal, when multiplexing LCD segment signal output with key source signal output, and when using one of the P0D0/ADC2 through P0D3/ADC5 pins as an A/D converter pin. (1) Notes on using general-purpose output port for key source signal
P0D3/ADC5 P0D2/ADC4 P0D1/ADC3 Switch A P0D0/ADC2 General-purpose output port
Latch
The "HALT 0001B" instruction is executed after a general-purpose output port for key source signal goes high. If an alternate switch such as switch A in the above figure is used at this time, a high level is always applied to the P0D0/ADC2 pin while switch A is closed, and the halt status is immediately released. Therefore, care must be execised in using the alternate switch. When using a general-purpose output port for key source signal, reset the KSEN flag of the LCD mode select register (RF address 10H) to "0". At this time, the P0D0/ADC2 through P0D3/ADC5 pins are automatically pulled down.
119
PD17016, 17017
(2) Notes on multiplexing LCD segment signal output and key source signal output
P0D3/ADC5 P0D2/ADC4 P0D1/ADC3 P0D0/ADC2 LCD15/KS15
Latch
LCD segment signal H LCD segment signal output L waveform
220 s Key source signal
Execute the "HALT 0001B" instruction after setting key source signal output data. At this time, the halt status is not released even if a high level of the LCD segment signal is input to the pin whose key source signal output data is "0". To multiple LCD segment signal output with key source signal output, set the KSEN flag of the LCD mode select register to 1. The key source signal data (setting the pin that outputs a key source) is set by the key source data register (KSR: peripheral address 42H) via the data buffer. The internal key latch circuit when LCD segment signal output is multiplexed with key source signal output latches data only while the key source signal is output, and is disconnected from the external source while the LCD segment signal is output. The internal pull-down resistor is ON only when the key source signal is output.
120
PD17016, 17017
(3) Notes on using P0D0/ADC2 to P0D3/ADC5 pin as A/D converter pin
A/D input Latch
A/D input
P0D3/ADC5 P0D2/ADC4 P0D1/ADC3 P0D0/ADC2
General-purpose output port or LCD segment signal output
When any of the P0D0/ADC2 through P0D3/ADC5 pins is used as an A/D converter pin, the selected pin (only one pin can be selected at one time) is disconnected from the input latch and is connected to the internal A/ D converter input. If a high level is input to the pin selected as an A/D converter pin at this time, the latch circuit holds the high level. If the "HALT 0001H" instruction is executed in this status, the halt status is immediately released even if the instruction can be executed because the input latch is at high level. To prevent this, set the pin in the input port mode before executing the "HALT 0001H" instruction, and set a low level for A/D converter input. (4) Others
P0D3/ADC5 P0D2/ADC4 Microcontroller, etc. P0D1/ADC3 P0D0/ADC2 General-purpose output port or LCD segment signal output
Output port
Latch
The P0D0/ADC2 through P0D3/ADC5 pins can also be used as general-purpose input port pins with pull-down resistors. Therefore, the halt status can also be controlled by using an external microcontroller as shown above.
121
PD17016, 17017
12.4.4 Releasing halt status by timer carry Releasing the halt status by the timer carry is set by the "HALT 0010B" instruction. When the release of the halt status is set by the timer carry, the halt status is released as soon as the timer carry FF has been set to "1". The timer carry FF corresponds to the BTM0CY flag of the timer carry FF judge register on a one-to-one basis, as explained in 11. TIMER FUNCTION, and is set to "1" at fixed time intervals (1 ms, 5 ms, 100 ms, or 250 ms). Therefore, the halt status can be released at fixed time intervals. Example M1 MEM CLR2 0.10H 0010B ; 1-second counter ; Symbol definition ; Embedded macro ; Sets timer carry FF setting time to 250 ms LOOP: HALT SKT1 BR ADD SKT1 BR HLTTMR BTM0CY LOOP CY LOOP ; Sets release condition by timer carry FF and halt status ; Embedded macro ; Branches to LOOP if BTM0CY flag is not set ; Embedded macro ; Executes processing A if carry occurs
HLTTMR DAT
BTM0CK1, BTM0CK0
M1, #0100B ; Adds 0100B to contents of M1
Processing A BR LOOP
In this example, the halt status is released every 250 ms and processing A is executed every 1 second. 12.4.5 Releasing halt status by interrupt Releasing the halt status by an interrupt is set by the "HALT 1000B" instruction. If releasing the halt status by an interrupt is set, the halt status is released as soon as the interrupt has been acknowledged. Two interrupt sources, INT0 pin and timer, are available as explained in 10. INTERRUPT. Therefore, the interrupt source to be used to release the halt status must be specified by program in advance. So that the interrupt is acknowledged, all the interrupts must be enabled (by the EI instruction), each interrupt is enabled (by setting the corresponding interrupt permission flag), in addition that the interrupt request must be issued from each interrupt source. Even if an interrupt request is issued, if that interrupt is not enabled, the interrupt is not acknowledged and the halt status is not released. When the halt status has been released because the interrupt has been acknowledged, the program flow branches to the vector address of the interrupt. If the "RETI" instruction is executed after the interrupt processing, the program flow returns to the instruction next to the "HALT" instruction. Here is an example.
122
PD17016, 17017
Example HLTINT INTTM DAT DAT 1000B 0003H 0005H ; Symbol definition of halt condition ; Interrupt vector address symbol definition ; ; Program address 0000H BR ORG ORG INTTM BR INT0PIN Processing A BR INTTIMER: Processing B EI_RETI: EI RETI MAIN: SET2_IPTM_IP0 SET2 ; Software macro ; Embedded macro ; Sets time interval of timer interrupt to 1 ms LOOP: Processing C EI HALT ; <1> BR LOOP ; Main routine processing ; Enables all interrupts HLTINT ; Specifies releasing halt by interrupt BTM1CK1, BTM1CK0 ; Interrupt processing by timer EI_RETI MAIN ; Timer interrupt vector address (0003H) INTTIMER ; INT0 pin interrupt vector address (0005H) ; Interrupt processing by INT0 pin
INT0PIN DAT START:
In this example, the halt status is released when the timer interrupt is acknowledged, and processing B is executed. When the INT0 pin interrupt is acknowledged, processing A is executed. Each time the halt status is released, processing C is executed. If the INT0 pin interrupt request and timer interrupt request are issued at the same time in the halt status, processing A of the INT0 pin, which has the higher hardware priority, is executed. If "RETI" is executed after execution of processing A, execution restores to the "BR LOOP" instruction in <1>, but the "BR LOOP" instruction is not executed, and the timer interrupt is immediately acknowledged. If "RETI" is executed after processing B of the timer interrupt has been executed, the "BR LOOP" instruction is executed.
123
PD17016, 17017
Caution When executing the HALT instruction which is to be released if the interrupt request flag (IRQxxx) for which the interrupt permission flag (IPxxx) is set is set, describe a NOP instruction immediately before the HALT instruction. If a NOP instruction is described immediately before the HALT instruction, a time of one instruction is generated in between the IRQxxx manipulation instruction and HALT instruction. In the case of the CLR1 IRQxxx instruction, for example, clearing IRQxxx is correctly reflected on the HALT instruction (refer to Example 1 below). If a NOP instruction is not described immediately before the HALT instruction, the CLR1 IRQxxx instruction is not correctly reflected on the HALT instruction, and the HALT mode is not set (refer to Example 2 below). Example 1. Program that correctly executes HALT instruction .........
; Sets IRQxxx IRQxxx ; Describes NOP instruction immediately before ; HALT instruction ; (clearing IRQxxx is correctly reflected on HALT ; instruction)
CLR1 NOP
HALT ......
1000B
; Correctly executes HALT instruction ; (HALT mode is set)
2. Program that does not set HALT mode
.........
; Sets IQRxxx IRQxxx 1000B ; Clearing IRQxxx is not reflected on HALT instruction ; (but on instruction next to HALT) ; HALT instruction is ignored (HALT mode is not set)
CLR1 HALT ......
124
PD17016, 17017
12.4.6 If two or more release conditions are simultaneously set If two or more release conditions are simultaneously set, and if even one of the conditions is satisfied, the halt status is released. The method to identify the release condition that is satisfied when two or more release conditions are specified is shown below. Example 1. HLTINT HLTTMR HLTKEY INT0PIN START: ORG BR MAIN INT0PIN Processing A EI RETI TMRUP Processing B RET KEYDEC: Processing C RET MAIN: MOVT PUT SET2 DBF, @AR KSR, DBF KSEN, LCDEN ; Sets key source output data (table reference) ; to key source data register (KSR) ; ; ; ; ; ; ; Embedded macro Multiplexes LCD segment signal output with key source signal output Embedded macro Sets timer carry FF setting time to 1 ms Software macro Enables INT0 pin interrupt ; Key input processing ; Timer carry processing ; INT0 pin interrupt processing DAT DAT DAT DAT 1000B 0010B 0001B 0005H
; INT0 pin interrupt vector address symbol ; definition
SET2
BTM0CK1, BTM0CK0
SET1_IP0 EI LOOP: HALT
SKF1 CALL SKF1 CALL BR
HLTINT OR HLTTMR OR HLTKEY ; Specifies interrupt, timer carry, and key input ; as halt release conditions BTM0CY ; Embedded macro ; Detects TMCY flag TMRUP ; Timer carry processing if set to "1" KEYJ ; Embedded macro ; Detects key input latch KEYDEC ; Key input processing if latched LOOP
125
PD17016, 17017
In example 1 above, three halt release conditions are specified: INT0 pin interrupt, 1-ms timer carry, and key input. To detect which condition has caused the halt status to be released, the vector address, BTM0CY flag, and KEYJ flag are detected to identify the interrupt, timer carry, and key input, respectively. When using two or more release conditions, the following two points must be noted. (1) All the specified release conditions must be detected when the halt status has been released. (2) The conditions must be sequentially detected starting from the one with the highest priority. For example, if the program below "MAIN:" in example 1 above is as shown in example 2 below, care must be exercised. Do not develop the program as shown in example 2 if the timer carry has a high priority. Example 2. MAIN: SET4 SET2 ; SET1_IP0 EI LOOP: HALT SKF4 BR SKF1 CALL BR KEYDEC: Processing C BR LOOP HLTINT OR HLTTMR OR HLTKEY P0D3, P0D2, P0D1, P0D0 ; Detects key input KEYDEC BTM0CY TMRUP LOOP ; Key input processing P1C3, P1C2, P1C1, P1C0 ; Uses general-purpose output port as key BTM0CK1, BTM0CK0 ; source signal
In example 2 above, suppose the timer carry FF is set to "1" immediately after the halt status has been released by key input. Then the program executes the "HALT" instruction again after executing the key input processing. Because the timer carry FF remains set at this time, the halt status is immediately released. Usually, however, a high level is input for about 100 ms as key input. Consequently, execution further branches to the key input processing. As a result, the timer carry FF is not correctly detected.
126
PD17016, 17017
12.5 Clock Stop Function
The clock stop function stops the 4.5-MHz crystal oscillation circuit by executing the "STOP s" instruction (clock stop status). Therefore, the current consumption of the device is decreased to the minimum value of 15 A. For the details on the current consumption, refer to 12.7 Current Consumption in Halt Status and Clock Stop Status. Specify "0000B" as operand "s" of the "STOP s" instruction. The "STOP s" instruction is valid only while the CE pin is low. It is executed as a no-operation (NOP) instruction even when executed while the CE pin is high. In other words, the "STOP s" instruction must be executed while the CE pin is low. The clock stop status is released by raising the level of the CE pin from low to high (CE reset). The following subsections 12.5.1 through 12.5.3 explain the clock stop status, how to release the clock stop status, and notes on using the clock stop instruction. 12.5.1 Clock stop status Because the crystal oscillation circuit is stopped in the clock stop status, all the device operations, such as those of the CPU and peripheral hardware, are stopped. For the operations of the CPU and peripheral hardware, refer to 12.6 Device Operations in Halt and Clock Stop Status. The power failure detection circuit does not operate in the clock stop status even if the supply voltage VDD of the device is lowered to 2.2 V. Therefore, the data memory can be backed up at a low voltage. For the details on the power failure detection circuit, refer to 13. RESET. 12.5.2 Releasing clock stop status The clock stop status is released either by raising the level of the CE pin from low to high (CE reset), or by lowering the supply voltage VDD of the device to 2.2 V or less once, and then increasing it to 4.5 V (power-ON reset). Figures 12-4 and 12-5 respectively show how the clock stop is released on CE reset and power-ON reset. If the clock stop status is released by power-ON reset, the power failure detection circuit operates. For the details on power-ON reset, refer to 13.4 Power-ON Reset.
127
PD17016, 17017
Figure 12-4. Releasing Clock Stop Status by CE Reset
5V VDD 0V H CE pin L H XOUT pin L About 50 ms STOP s instruction Program starts from address 0 (CE reset)
5V VDD 0V H CE pin L H XOUT pin L
Operation is as follows if clock stop instruction is not used
0 - tSET Program starts from address 0 (CE reset) CE reset is effected in synchronization with setting of timer carry FF after CE pin has gone high
Figure 12-5. Releasing Clock Stop Status by Power-ON reset
5V VDD 0V H CE pin L H XOUT pin L About 50 ms STOP s instruction Program starts from address 0 (Power-ON reset) 2.2 V
5V VDD 0V H CE pin L H XOUT pin L
Operation is as follows if clock stop instruction is not used 3.5 V
About 50 ms Oscillation stops Program starts from address 0 (Power-ON reset)
128
PD17016, 17017
12.5.3 Notes on using clock stop instruction The clock stop (STOP s) instruction is valid only while the CE pin is low. Therefore, processing to be performed if the CE pin happens to be high must be taken into consideration. Take the following program as an example. Example XTAL CEJDG: ; <1> SKF1 BR CE MAIN ; Embedded macro ; Detects input level of CE pin ; Branches to main processing if CE = high ; Processing of CE = low DAT 0000B ; Symbol definition of clock stop condition
Processing A ; <2> STOP ; <3> BR MAIN: Main processing BR CEJDG $-1 XTAL
; Clock stop
In the above example, the status of the CE pin is detected in <1>. If the CE pin is low, processing A is performed and then the clock stop instruction "STOP XTAL" in <2> is executed. If the CE pin goes high while the "STOP XTAL" instruction in <2> is executed, however, the "STOP XTAL" instruction is treated as a no-operation (NOP) instruction. Should branch instruction "BR$-1" in <3> be missing at this time, the program would execute the main processing, causing malfunctioning. Therefore, either a branch instruction must be inserted as in <3>, or the program must be designed in the manner that malfunctioning does not occur even if the main processing is executed. If a branch instruction is used as in <3>, CE reset is executed in synchronization with the next setting of the timer carry FF even while the CE pin is high.
5V VDD CE pin L
Main processing Processing A
0V H
< 1 >< 1 >< 1 > Detection of CE pin
< 2 > STOP XTAL is treated as NOP instruction because CE pin is high.
Program starts from address 0 in synchronization with setting of timer carry FF (CE reset).
129
PD17016, 17017
12.6 Device Operations in Halt and Clock Stop Status
Table 12-1 shows the operations of the CPU and peripheral hardware in the halt status and clock stop status. As shown in this table, all the peripheral hardware units continue the normal operation in the halt status, except that instruction execution is stopped. All the peripheral hardware units stop operation in the clock stop status. The control registers that control the operations of the peripheral hardware units operate normally in the halt status (i.e., are not initialized), but are initialized to specific values in the clock stop status (as soon as the STOP s instruction has been executed). To put in another way, the peripheral hardware units continue the operations set by the control registers in the halt status, and operate in accordance with the control registers that are initialized to specific values in the clock stop status. For the values to which the control registers are initialized, refer to 8. REGISTER FILE (RF). Table 12-1. Device Operations in Halt Status and Clock Stop Status
Peripheral Hardware CE Pin = High Halt Program counter Stops at address of HALT instruction Retained Retained Retained Normal operation Normal operation Normal operation Normal operation Normal operation Normal operation Normal operation Normal operation Normal operation Clock Stop STOP instruction is invalid (NOP) Halt Stops at address of HALT instruction Retained Retained Retained Normal operation Disabled Normal operation Normal operation Normal operation Normal operation Normal operation Normal operation Normal operation Status CE Pin = Low Clock Stop Initialized to 0000H and stops InitializedNote Retained InitializedNote Stops operation Disabled Stops operation Stops operation Stops operation Stops operation Stops operation Stops operation Stops operation
System register Peripheral register Control register Timer PLL frequency synthesizer A/D converter D/A converter BEEP output Serial interface Frequency counter LCD controller/driver Key source controller/ decoder General-purpose I/O port General-purpose input port General-purpose output port
Normal operation Normal operation Normal operation
Normal operation Normal operation Normal operation
Input port Input port Retained
Note
For the value to which these registers are initialized, refer to 5. SYSTEM REGISTER (SYSREG) and 8. REGISTER FILE (RF).
130
PD17016, 17017
12.7 Current Consumption in Halt Status and Clock Stop Status
12.7.1 Device current consumption in halt status Figure 12-6 shows the device current consumption IDD in the halt status. Current consumption curves <1> through <4> in this figure were drawn by using the programs shown below. As shown in Figure 12-6, the less the halt status is released, the lower the current consumption. (1) Program 1 The HALT instruction is not used. Example NOP BR (2) Program 2 A 5-ms timer interrupt is specified as the halt release condition, and 20 instructions (about 90 s) are executed each time the halt status has been released. Example HLTINT INTTM DAT DAT BR ORG REPT ENDR EI RETI LOOP: INITFLG BTM1CK1, NOT BTM1CK0 ; SET_IPTM EI HALT BR HLTINT $-1 TMINT 17 NOP 1000B 0003H LOOP $-1
131
PD17016, 17017
(3) Program 3 A 100-ms timer interrupt is specified as the halt release condition, and 20 instructions are executed each time the halt status has been released. Example HLTINT INTTM DAT DAT BR ORG REPT ENDR EI RETI LOOP: CLR2 ; SET1_IPTM EI HALT BR (4) Program 4 Nothing is set as the halt release condition. Example HLTNORLS DAT HALT HLTNORLS The device current consumption IDD shown in Figure 12-6 were measured under the following conditions. * PLL is disabled. * The frequency counter is disabled. * A sine wave with a frequency fIN = 4.5 MHz and input amplitude VIN = VDD is input to the XIN pin from a standard signal generator. * All the pins set in the output mode are open. * All the pins set in the input mode are pulled down by a 47-k resistor (except the XIN pin). 12.7.2 Device current consumption in clock stop status Figure 12-7 shows the device current consumption IDD in the clock stop status. The current consumption shown in this figure were measured under the following conditions. * All the pins set in the output mode are open. * All the pins set in the input mode are pulled down by a 47-k resistor (except the XIN pin). * A crystal resonator is connected (however, oscillation is stopped). 0000B HLTINT $-1 BTM1CK1, BTM1CK0 TMINT 17 NOP 1000B 0003H LOOP
132
PD17016, 17017
Figure 12-6. Device Current Consumption in Halt Status (Reference Value) (a) IDD vs. VDD (TA = 25 C)
(1)
Supply current IDD (mA)
(b) IDD vs. TA (VDD = 5.5 V)
1.5
Supply current IDD (mA)
1.5
(1)
1.0
1.0
0.5
(2) (3) (4) 3.5 4.0 4.5 5.0 5.5
0.5
(2) (3) (4)
0
0
-40
0
25
85
Supply voltage VDD (V)
Ambient temperature TA (C)
Figure 12-7. Device Current Consumption in Clock Stop Status (Reference Value) (a) IDD vs. VDD (TA = 25 C) (b) IDD vs. TA (VDD = 5.5 V)
3.0
3.0
2.0
Supply current IDD ( A)
2.2 2.5
Supply current IDD( A)
2.0
1.0
1.0
0
3.0
3.5
4.0
4.5
5.0
5.5
0
-40
0
25
85
Supply voltage VDD (V)
Ambient temperature TA (C)
12.7.3 Notes on processing each pin in halt and clock stop status The halt status is used to reduce the current consumption, for example, when only the watch operates. The clock stop function is used to reduce the current consumption when only the contents of the data memory are to be retained. Therefore, the current consumption must be reduced as much as possible in the halt and clock stop statuses. At this time, the current consumption may increase depending on the status of each pin, and therefore the points shown in Table 12-2 must be noted.
133
PD17016, 17017
Table 12-2. Notes on Status of Each Pin in Halt and Clock Stop Statuses (1/2)
Pin Function Pin Symbol Status of Each Pin and Notes on Processing Halt Generalpurpose port Port 0A P0A3 P0A2 P0A1 P0A0 Port 0B P0B3 P0B2/SCK P0B1/SO P0B0/SI Port 0C P0C3 P0C2 P0C1 P0C0 Port 1A P1A3 P1A2 P1A1 P1A0 P0D3/ADC5 P0D2/ADC4 P0D1/ADC3 P0D0/ADC2 Port 1D P1D3/FMIFC P1D2/AMIFC P1D1/ADC1 P1D0/ADC0 Generalpurpose output port Port 1B P1B3 P1B2/PWM1 P1B1/PWM0 P1B0/BEEP Port 1C P1C3 P1C2 P1C1 P1C0 Port 2A Interrupt P2A0 INT0 (2) Previous status before halt status is set is retained as is. (1) In output mode Current consumption increases if these pins are externally pulled down while they output high level, or externally pulled up while they output low level. Pay attention to N-ch open-drain output pins (P0A3, P0A2, and P1B3-P1B0). In input mode (except ports 1A and 1D) Current consumption increases due to noise if these pins are floated. (3) Port 0D (P0D3/ADC5-P0D0/ADC2) Current consumption increases if these pins are externally pulled up because they have pull-down resistor. However, pull-down resistor of pin selected as A/D converter pin is OFF. (4) Ports 1D (P1D3/FMIFC-P1D0/ ADC0) and 1A (P1A3-P1A0) Current consumption increases when P1D3/FMIFC and P1D2/ AMIFC pins are used for IF counter because internal amplifier operates. Because IF counter is not automatically disabled even if CE pin goes low, it must be initialized by program as necessary. Ports 1D and 1A are designed to prevent increase in current consumption due to noise even if they are set in general purpose input port mode and floated. Clock stop All these pins are set in general-purpose input port mode. All input ports, except port 0C (P0C3P0C0), are designed to prevent increase in current consumption due to noise even if they are externally floated. Port 0C (P0C3-P0C0) must be externally pulled down or up so that current consumption does not increase due to noise. Port 0D (P0D3/ADC5-P0D0/ADC2) is internally pulled down.
Generalpurpose input port
Port 0D
These pins are set in general-purpose output port pins. Output contents are retained as is. Therefore, current consumption increases if these pins are externally pulled down while they output high level, or pulled up while they output low level.
Current consumption increase due to external noise if this pin is floated.
134
PD17016, 17017
Table 12-2. Notes on Status of Each Pin in Halt and Clock Stop Statuses (2/2)
Pin Function Pin Symbol Status of Each Pin and Notes on Processing Halt LCD segment LCD29/P0F3 | LCD26/P0F0 LCD25/P0E3 | LCD22/P0E0 LCD21 | LCD16 LCD15/KS15 | LCD0/KS0 PLL frequency synthesizer VCOL VCOH EO0 EO1 Current consumption increases during PLL operation. These pins are as follows when PLL is disabled. VCOL and VCOH EO0 and EO1 : internally pulled down : floated PLL is disabled. These pins are as follows. VCOL and VCOH EO0 and EO1 : internally pulled down : floated Same as above general-purpose output ports applies if these pins are used in general-purpose output port mode. If they output key source signals, current consumption increases via port 0D (with pull-down resistor) if there is switch that is always ON such as transistor switch and if "1" is output as key source data. Clock stop All pins are set in LCD segment signal output mode and output low level (display off).
PLL is automatically disabled when CE pin goes low. Crystal oscillation circuit XIN XOUT Current consumption changes due to oscillation waveform of crystal oscillation circuit. Current consumption decreases as oscillation amplitude increases. Because oscillation amplitude is influenced by crystal resonator and load capacitor used, evaluation must be performed. XIN pin is internally pulled down, and XOUT pin outputs high level.
135
PD17016, 17017
13. RESET
The reset function is used to initialize the device operation.
13.1 Configuration of Reset Block
Figure 13-1 shows the configuration of the reset block. The device is reset in two ways: by applying supply voltage VDD (power-ON reset or VDD reset) and by using the CE pin (CE reset). The power-ON reset block consists of a voltage detection circuit that detects a voltage input to the VDD pin, a power failure detection circuit, and a reset control circuit. The CE reset block consists of a circuit that detects the rising of a signal input to the CE pin, and a reset control circuit. Figure 13-1. Configuration of Reset Block
XOUT XIN BTM0CY flag read R Q S
Timer carry disable FF
Power failure detection block Timer FF block Divider Selector
STOP s instruction
Timer carry
VDD
Voltage detection circuit Rising detection circuit
Power-ON clear signal (POC) Reset control circuit
Reset signal IRES RES RESET
Forced halt by timer carry
Control register System register Stack Program counter
CE
STOP instruction
136
PD17016, 17017
13.2 Reset Function
Power-ON reset is effected when supply voltage VDD rises from a specific level, and CE reset is effected when the CE pin goes high. Power-ON reset initializes the program counter, stack, system register, and control registers, and executes the program from address 0000H. CE reset initializes the program counter, stack, system register, and some control registers, and executes the program from address 0000H. The major differences between power-ON reset and CE reset are the control registers that are initialized and the operation of the power failure detection circuit that is explained in 13.6. Both power-ON reset and CE reset are controlled by the reset signals IRES, RES, and RESET output from the reset control circuit shown in Figure 13-1. Table 13-1 shows the relation among the IRES, RES, and RESET signals, and power-ON reset, and CE reset. The reset control circuit also operates when the clock stop instruction (STOP s) explained in 12. STANDBY is executed. The following sections 13.3 and 13.4 respectively explain CE reset and power-ON reset. Section 13.5 explains the relation between CE reset and power-ON reset. Table 13-1. Relation between Internal Reset Signals and Each Reset Operation
Internal Reset Signal CE Reset x Output Signal Power-ON Reset IRES Forcibly sets device in halt status. Halt status is released when timer carry FF is set. RES RESET x Initializes some control registers. Initializes program counter, stack, system register, and some control registers. Clock Stop Control Operation by Each Reset Signal
137
PD17016, 17017
13.3 CE Reset
CE reset is effected when the CE pin goes high. When the CE pin goes high, the RESET signal is output in synchronization with the rising edge of the next timer carry FF setting pulse, and the device is reset. When CE reset is effected, the RESET signal initializes the program counter, stack, system register, and some control registers, and the program is executed starting from address 0000H. For the value to which each of the above registers is initialized, refer to the description of each register. The operation of CE reset differs depending on whether the clock stop instruction is used. The differences in operation are explained in the following subsections 13.3.1 and 13.3.2. Subsection 13.3.3 explains the points to be noted on using CE reset. 13.3.1 CE reset when clock stop (STOP s) instruction is not used Figure 13-2 shows the operation of CE reset when the clock stop (STOP s) instruction is not used. When the STOP s instruction is not used, the timer mode select register of the control registers is not initialized. After the CE pin has gone high, therefore, the RESET signal is output at the rising edge of the timer carry FF setting pulse (1 ms, 5 ms, 100 ms, 250 ms) selected at that time, and the device is reset. Figure 13-2. CE Reset Operation When Clock Stop Instruction Is Not Used
5V VDD 0V H CE XOUT L H L H L H L H L H L Normal operation Normal operation CE reset is effected at rising of timer carry FF setting pulse. If selected timer carry FF setting time is tSET, this period "t" is 0 < t < tSET depending on timing of rising of CE pin. During this period, program continues its operation.
Timer carry FF setting pulse
IRES RES RESET
138
Reset signals
PD17016, 17017
13.3.2 CE reset when clock stop (STOP s) instruction is used Figure 13-3 shows the operation of CE reset when the clock stop (STOP s) instruction is used. When the STOP s instruction is used, the IRES, RES, and RESET signals are output as soon as the STOP s instruction has been executed. At this time, the timer mode select register of the control registers is initialized to 0000B by the RES signal, the timer carry FF setting signal is set to 100 ms. Because the IRES signal is output while the CE pin is low, the halt status, which can be released by the timer carry, is forcibly set. However, the device stops operation because the clock is stopped. When the CE pin goes high, the clock stop status is released, and oscillation starts. Because the halt status that can be released by the timer carry is set at this time by the IRES signal, the program starts from address 0 when the CE pin goes high and then the timer carry FF setting pulse rises. Because the timer carry FF setting pulse is initialized to 100 ms, CE reset is effected 50 ms after the CE pin has gone high. Figure 13-3. CE Reset Operation When Clock Stop Instruction Is Used
5V VDD 0V H CE XOUT Timer carry FF setting pulse Reset signals IRES L H L H L H L H L H L Normal operation
Clock stop status
RES RESET
Halt status 50 ms CE reset Program starts from address 0.
Stop s instruction Clock oscillation starts Stop released
139
PD17016, 17017
13.3.3 Notes on CE reset Because CE reset is effected regardless of the instruction under execution, the following points <1> and <2> must be noted. (1) Time to execute timer processing such as watch When developing a watch program by using the timer carry or timer interrupt, the processing of that program must be completed in specific time. For details, refer to 11.3.7 Notes on using timer carry and 11.4.5 Notes on using timer interrupt. (2) Processing of data and flag used for program Care must be exercised in rewriting the contents of data or flag that cannot be processed with one instruction and whose contents must not change even when CE reset is effected, such as a security code. This is explained in detail by using the following examples.
140
PD17016, 17017
Example 1. R1 R2 R3 R4 M1 M2 START: Key input processing R1 contents of key A R2 contents of key B SET2 SUB SUB SKT1 BR MAIN: Key input processing R3 contents of key C R4 contents of key D ST ST BR ERROR: Must not operate Suppose the current security code is "12H" in the above program, the contents of data memory areas M1 and M2 are "1H" and "2H", respectively. If CE reset is effected, the contents of key input are compared with security code "12H" in <1>. If they coincide, the normal processing is performed. If the security code is changed by the main processing, the new code is written to M1 and M2 in <2> and <3>. Suppose the security code is changed to "34H", "3H" and "4H" are written to M1 and M2, respectively, in <2> and <3>. If CE reset is effected at the point where <2> is executed, the program is executed from address 0000H without <3> executed. Consequently, the security code is changed to "32H", making impossible to clear the security. In this case, use the program shown in following Example 2. ; Security code rewriting mode ; Substitutes contents of pressed key into R3 and R4. ; Security code input wait mode ; Substitutes contents of pressed key into R1 and R2. MEM MEM MEM MEM MEM MEM 0.01H 0.02H 0.03H 0.04H 0.11H 0.12H ; First digit of key input data of security code ; Second digit of key input data of security code ; First digit data for changing security code ; Second digit data for changing security code ; First digit of current security code ; Second digit of current security code
CMP, Z ;<1> ; Compares security code with input data. R1, M1 R2, M2 Z ERROR ; Input data is different from security code.
M1, R3 ;<2> ; Rewrites security code. M2, R4 ;<3> MAIN
141
PD17016, 17017
Example 2. R1 R2 R3 R4 M1 M2 MEM MEM MEM MEM MEM MEM 0.01H 0.02H 0.03H 0.04H 0.11H 0.12H 0.13H.0 ; First digit of key input data of security code ; Second digit of key input data of security code ; First digit data for changing security code ; Second digit data for changing security code ; First digit of current security code ; Second digit of current security code ; "1" while security code is changed
CHANGE FLG START:
Key input processing R1 contents of key A R2 contents of key B SKT1 BR ST ST CLR1 SECURITY_CHK: SET2 SUB SUB SKT1 BR MAIN: Key input processing R3 contents of key C R4 contents of key D SET1 ST ST CLR1 BR ERROR: Must not operate In the program in Example 2, the CHANGE flag is set to "1" in <5> before the security code is changed in <2> and <3>. Therefore, the security code is rewritten in <4> even if CE reset is effected before <3> is executed. ; Security code rewriting mode ; Substitutes contents of pressed key into R3 and R4. CMP, Z ;<1> ; Compares security code with input data. R1, M1 R2, M2 Z ERROR ; Input data is different from security code. ; Security code input wait mode ; Substitutes contents of pressed key into R1 and R2.
CHANGE ;<4> ; If CHANGE flag is "1" SECURITY_CHK M1, R3 M2, R4 CHANGE ; rewrites M1 and M2.
CHANGE ;<5> ; Until security code is changed ; Sets CHANGE flag to "1". M1, R3 ;<2> ; Rewrites security code M2, R4 ;<3> CHANGE MAIN ; When security code has been changed, sets ; CHANGE flag to "0".
142
PD17016, 17017
13.4 Power-ON Reset
Power-ON reset is effected when the supply voltage VDD of the device rises from a specific level (called powerON clear voltage). If the supply voltage VDD is lower than the power-ON clear voltage, a power-ON clear signal (POC) is output from the voltage detection circuit shown in Figure 13-1. When the power-ON clear voltage is output, the crystal oscillation circuit is stopped, and the device operation is stopped. While the power-ON clear signal is output, the IRES, RES, and RESET signals are output. If supply voltage VDD exceeds the power-ON clear voltage, the power-ON clear signal is cleared, and crystal oscillation is started. At the same time, the IRES, RES, and RESET signals are also cleared. At this time, the halt status is set to be released by the timer carry due to the IRES signal. Therefore, powerON reset is effected at the rising edge of the next timer carry FF setting signal. The timer carry FF setting signal is initialized to 100 ms by the RESET signal. For this reason, reset is effected 50 ms after supply voltage VDD has exceeded the power-ON clear voltage, and the program is started from address 0. This operation is illustrated in Figure 13-4. The program counter, stack, system register, and control registers are initialized as soon as the power-ON clear signal has been output. For the value to which each of the above registers is to be initialized, refer to the description of each register. The power-ON clear voltage is 3.5 V (rated value) during normal operation, and 2.2 V (rated value) in the clock stop status. The operations performed when the power-ON clear voltage is at the respective levels are explained in 13.4.1 and 13.4.2. The operation to be performed if the supply voltage VDD rises from 0 V is explained in 13.4.3. Figure 13-4. Operation of Power-ON Reset
5V VDD 0V H CE XOUT Timer carry FF setting pulse Power-ON clear signal IRES L H L H L H L H L H L H L Normal operation Device operation stops Halt status 50 ms Power-ON clear released Oscillation starts Power-ON reset Program starts from address 0. Power-ON clear voltage
Reset signals
RES RESET
143
PD17016, 17017
13.4.1 Power-ON reset during normal operation Figure 13-5 (a) shows the operation. As shown in the figure, the power-ON clear signal is output and the device operation stops regardless of the input level of the CE pin, if the supply voltage VDD drops below 3.5 V. If VDD rises beyond 3.5 V again, the program starts from address 0000H after 50 ms of halt status. The "normal operation" is when the clock stop instruction is not used and includes the halt status that is set by the halt instruction. 13.4.2 Power-ON reset in clock stop status Figure 13-5 (b) shows the operation. As shown in the figure, the power-ON clear signal is output and the device operation stops if supply voltage VDD drops below 2.2 V. However, it seems as if the device operation were not changed because the device is in the clock stop status. When supply voltage VDD rise beyond 3.5 V next time, the program starts from address 0000H after 50 ms of halt status. 13.4.3 Power-ON reset when supply voltage VDD rises from 0 V Figure 13-5 (c) shows the operation. As shown in the figure, the power-ON clear signal is output until supply voltage VDD rises from 0 V to 3.5 V. When VDD rises beyond the power-ON clear voltage, the crystal oscillation circuit starts operating, and the program starts from address 0000H after 50 ms of halt status.
144
PD17016, 17017
Figure 13-5. Power-ON Reset and Supply Voltage VDD (a) During normal operation (including halt status)
5V 3.5 V VDD 0V H CE L H XOUT Power-ON clear signal L H L Normal operation Device operation stops Halt status 50 ms Power-ON clear released Oscillation starts Power-ON reset Program starts from address 0. Power-ON clear voltage
(b) In clock stop status
5V 3.5 V VDD 0V CE XOUT Power-ON clear signal H L H L H L Normal operation 2.2 V Power-ON clear voltage
Clock stop
Device operation stops
Halt status Power-ON reset Program starts from address 0.
STOP s instruction
50 ms Power-ON clear released Oscillation starts
(c) When supply voltage VDD rises from 0 V
5V 3.5 V VDD 0V H CE XOUT Power-ON clear signal L H L H L Device operation stops Halt status Power-ON reset Program starts from address 0. 50 ms Power-ON clear released Oscillation starts Power-ON clear voltage
145
PD17016, 17017
13.5 Relation between CE Reset and Power-ON Reset
There is a possibility that power-ON reset and CE reset are effected at the same time when power is first applied. The reset operations performed at this time are explained in 13.5.1 through 13.5.3. 13.5.4 explains the points to be noted in raising supply voltage VDD. 13.5.1 If VDD pin and CE pin rise simultaneously Figure 13-6 (a) shows the operation. At this time, the program starts from address 0000H due to power-ON reset. 13.5.2 If CE pin rises in forced halt status of power-ON reset Figure 13-6 (b) shows the operation. At this time, the program starts from address 0000H due to power-ON reset in the same manner as in 13.5.1. 13.5.3 If CE pin rises after power-ON reset Figure 13-6 (c) shows the operation. At this time, the program starts from address 0000H due to power-ON reset, and the program starts from address 0000H again at the rising of the next timer carry FF setting signal because of CE reset.
146
PD17016, 17017
Figure 13-6. Relation between Power-ON Reset and CE Reset (a) If VDD and CE pins rise simultaneously
5V 3.5 V VDD 0V H CE L H Timer carry FF setting pulse L Operation stops Halt status 50 ms Power-ON clear voltage
Normal operation
Power-ON reset Program starts
(b) If CE pin rises in halt status
5V 3.5 V VDD 0V H CE L H Timer carry FF setting pulse L Operation stops Halt status 50 ms
Power-ON clear voltage
Normal operation
Power-ON reset Program starts
(c) If CE pin rises after power-ON reset
5V VDD 0V H CE L H Timer carry FF setting pulse L Operation stops 3.5 V Power-ON clear voltage
Halt status 50 ms
Normal operation CE reset Program starts
Power-ON reset Program starts
147
PD17016, 17017
13.5.4 Notes on raising supply voltage VDD When raising supply voltage VDD, keep in mind the following points (1) and (2). (1) When raising supply voltage VDD from power-ON clear voltage It is necessary to raise supply voltage VDD to higher than 3.5 V at least once. This is illustrated in Figure 13-7. Suppose, for example, only a voltage less than 3.5 V is applied on application of VDD with a program that backs up VDD at 2.2 V by using the clock stop instruction, as shown in Figure 13-7, the power-ON clear signal is continuously output, and the program does not operate. Because the output ports of the device output undefined values, the current consumption increases in some cases. If the device is backed up by batteries, therefore, the back-up time is substantially shortened. Figure 13-7. Notes on Raising VDD
5V 3.5 V VDD 2.2 V 0V H CE L H XOUT Timer carry FF setting pulse Power-ON clear signal L H L H L Operation stops Current consumption may increase during this period because output ports are undefined.
Operation stops
Power-ON clear voltage
Halt status 50 ms
Normal operation Initialization is executed during this period, and then clock stop instruction is executed.
Back up
Power-ON reset Program starts
STOP s instruction
148
PD17016, 17017
(2) Restoring from clock stop status To restore the device from the back-up status while supply voltage VDD is backed up at 2.2 V by using the clock stop instruction, VDD must be raised to 3.5 V or higher within 50 ms after the CE pin has gone high. As shown in Figure 13-8, the device is restored from the clock stop status by means of CE reset. Because the power-ON clear voltage is changed to 3.5 V 50 ms after the CE pin has gone high, power-ON reset is effected unless VDD is 3.5 V or higher at this point. The same applies when VDD is lowered. Figure 13-8. Restoring from Clock Stop Status
5V 3.5 V VDD 2.2 V 0V H CE L H XOUT Timer carry FF setting pulse Power-ON clear signal L H L H L Back up by clock stop instruction Halt status 50 ms Normal operation
Processing where CE = low
Power-ON clear voltage
Back up
CE reset Program starts Power-ON clear voltage is changed to 3.5 V at this point. Therefore, VDD must rise to 3.5 V or higher before this point.
STOP s instruction Power-ON clear voltage is changed to 2.2 V at this point. Therefore, VDD must not fall below 3.5 V before this point.
149
PD17016, 17017
13.6 Power Failure Detection
Power failure detection is used to judge whether power-ON reset by application of supply voltage VDD, or CE reset has been effected when the device is reset, as shown in Figure 13-9. Because the contents of the data memory and ports are "undefined" on power application, these contents are initialized by means of power failure detection. A power failure can be detected in two ways: by using the power failure detection circuit to detect the BTM0CY flag, and by detecting the contents of the data memory (RAM judgement). 13.6.1 and 13.6.2 explain how a power failure is detected by using the power failure detection circuit and BTM0CY flag. 13.6.3 and 13.6.4 explain how a power failure is detected by RAM judgement method. Figure 13-9. Power Failure Detection Flow Chart
Program starts Power failure detection Not power failure Power failure
Initializes data memory and output ports
13.6.1 Power failure detection circuit The power failure detection circuit consists of a voltage detection circuit, a timer carry disable flip-flop that is set by the output (power-ON clear signal) of the voltage detection circuit, and a timer carry, as shown in Figure 13-1. The timer carry disable FF is set to "1" by the power-ON clear signal, and is reset to "0" when an instruction that reads the BTM0CY flag is executed. When the timer carry disable FF is set to "1", the BTM0CY flag is not set to "1". When the power-ON clear signal is output (at power-ON reset), the program is started with the BTM0CY flag reset, and the BTM0CY flag is disabled from being set until an instruction that reads the BTM0CY flag is executed. Once the instruction that reads the BTM0CY flag has been executed, the BTM0CY flag is set each time the timer carry FF setting pulses has risen. It can be judged whether power-ON reset (power failure) or CE reset (not power failure) has been effected by detecting the contents of the BTM0CY flag when the device is reset. Power-ON reset has been effected if the BTM0CY flag is reset to "0"; CE reset has been effected if it is set to "1". The voltage at which a power failure can be detected is the same as the voltage at which power-ON reset is effected, or VDD = 3.5 V during crystal oscillation, or VDD = 2.2 V in the clock stop status. Figure 13-10 shows the transition of the status of the BTM0CY flag. Figures 13-11 and 13-10 show the timing chart and the operation of the BTM0CY flag.
150
PD17016, 17017
Figure 13-10. Status Transition of BTM0CY Flag
CE = low <1> CE = any VDD = low Operation stops VDD = L 3.5 V < 2 > Crystal oscillation starts Forced halt (approx. 50 ms) <3> Disables setting of BTM0CY flag. <4> Clock stop Power-ON reset CE = high
CE = L CE = H <7> <5> <6> STOP 0 CE = H L BTM0CY = 0 Normal Normal CE reset operation operation <8> CE = L H Normal operation Timer carry FF CE reset wait setting pulse rises. <9> CE = L H Crystal oscillation starts Forced halt (50 ms) < 10 > < 11 > SKT1 BTM0CY or SKT1 BTM0CY or SKF1 BTM0CY SKF1 BTM0CY
< 13 >
<12 >
Clock stop
STOP 0
Normal operation
CE = H L CE = L H
< 14 >
< 15 >
Normal operation
< 16 >
BTM0CY = 1
CE reset
Enables setting of BTM0CY flag
Normal operation CE reset wait
< 17 >
Timer carry FF setting pulse rises.
CE = L H
Crystal oscillation starts Forced halt (50 ms)
151
PD17016, 17017
Figure 13-11. Operation of BTM0CY Flag (a) When BTM0CY flag never detected (SKT1 BTM0CY or SKF1 BTM0CY is not executed)
5V VDD 0V H CE Timer carry FF setting pulse BTM0CY Operation in Figure 13-10 L <1> <2> <6> <3> Timer time changed <5> <8> <7> STOP 0000 B <6> <5> <4> <9> <7> <6> <1> L H L H
(b) When detecting power failure by BTM0CY flag
5V VDD 0V H CE Timer carry FF setting pulse BTM0CY
SKT1 BTM0CY instruction Operation in Figure 13-10
L H L H L < 1 > < 2 > <6> <14> <3>
< 11 > < 13 > < 16 > < 14 > < 13 > < 12 > < 17 > < 14 >
<1>
< 15 >
< 15 >
Timer time changed BTM0CY = 1 Not power failure
STOP 0000 B BTM0CY = 1 Not power failure
BTM0CY = 0 Power failure
152
PD17016, 17017
13.6.2 Notes on detecting power failure by BTM0CY flag The following points must be noted when using the BTM0CY flag for watch counting. (1) Updating watch When developing a watch program by using the timer carry, the watch must be updated after a power failure has been detected. This is because counting of the watch is skipped once because the BTM0CY flag is reset to "0" when the BTM0CY flag is read on detection of a power failure. (2) Watch updating processing time The processing to update the watch must be completed before the next timer carry FF setting pulse rises. This is because, if the CE pin goes high during the watch updating processing, CE reset is effected without the watch updating processing completed. For further information on (1) and (2) above, refer to 11.3.7 (b) Correction of timer carry on CE reset. When detecting a power failure, the following points must be noted. (3) Timing of power failure detection To count the watch by using the BTM0CY flag, the BTM0CY flag must be read to detect a power failure within the time since the program has started from address 0000H until the next timer carry FF setting pulse rises. For example if the timer carry FF setting time is set to 5 ms, and a power failure is detected 6 ms after the program has been started, the BTM0CY flag is overlooked once. For details, refer to 11.3.7 (b) Correction of timer carry on CE reset. Power failure detection and initial processing must be completed within the timer carry FF setting time as shown in the following example. This is because, if the CE pin goes high and CE reset is effected during power failure detection processing and initial processing, these processing may be stopped in midway, and thus problems may occur. To change the timer carry FF setting time by the initial processing, the instruction that changes the time must be executed at the end of the initial processing, and the instruction must be one instruction. This is because the initial processing may not be completely executed because of CE reset if the timer carry FF setting time is changed before the initial processing is executed, as shown in the following example.
153
PD17016, 17017
Example START: ;<1> Processing on reset ;<2> SKT1 BR BACKUP: ;<3> Watch updating BR INITIAL: ;<4> Initial processing ;<5> INITFLG BTM0CK1, NOT BTM0CK0 ; Embedded macro ; Sets timer carry FF setting time to 5 ms MAIN: Main processing SKT1 BR BTM0CY MAIN Watch updating BR MAIN MAIN BTM0CY INITIAL ; Power failure detection ; Program address 0000H
154
PD17016, 17017
Example of operation
VDD CE 5-ms pulse 50 ms 50-ms pulse Timer carry FF setting pulse H L 50 ms 5 ms 5V 0V H L
<1>
<4>
<1>
<3>
< 2 > Power failure detection If processing time of < 1 > + < 4 > is longer than 100 ms, CE reset is effected in middle of processing < 4 >.
< 2 > Power failure detection If processing time of < 1 > + < 3 > is too long, CE reset is effected.
CE reset <5>
CE reset
CE reset may be effected immediately depending on when timer carry FF setting time is changed. Therefore, if < 5 > is executed before < 4 >, power failure processing < 4 > may not be completely executed.
13.6.3 Power failure detection by RAM judgement method The RAM judgement method is to detect a power failure by judging whether the contents of the data memory at a specific address are the specified value. An example of a program that detects a power failure by the RAM judgement method is shown below. The RAM judgement method detects a power failure by comparing an "undefined" value with the "specified value" because the contents of the data memory are "undefined" on application of supply voltage VDD. Therefore, there is a possibility that a wrong judgment may be made as explained in 13.6.4 Notes on detecting power failure by RAM judgement method. When the RAM judgement method is used, however, the device can be backed up at a voltage lower than that at which a power failure is detected, by using the power failure detection circuit, as shown in Table 13-2. Table 13-2. Comparing Power Failure Detection by Power Failure Detection Circuit and RAM Judgement Method
Power Failure Detection Circuit Data hold voltage (in clock stop status) Operating status Effective value 1-2 V No malfunctioning Rated value 2.2 V RAM Judgement Method Effective value 0-1 V Rated value 2.0 V
Malfunctioning may occur
155
PD17016, 17017
Example Program to detect power failure by RAM judgement method M012 M034 M056 M107 M128 M16F DATA0 DATA1 DATA2 DATA3 DATA4 DATA5 START: SET2 SUB SUB SUB BANK1 SUB SUB SUB BANK0 SKF1 BR ;INITIAL: Initial processing MOV MOV MOV BANK1 MOV MOV MOV BR BACKUP: Backup processing MAIN: Main processing M107, #DATA3 M128, #DATA4 M16F, #DATA5 MAIN M012, #DATA0 M034, #DATA1 M056, #DATA2 Z BACKUP ; branches to BACKUP M107, #DATA3 M128, #DATA4 M16F, #DATA5 ; M107 = DATA3 and ; M128 = DATA4 and ; M16F = DATA5, CMP, Z M012, #DATA0 M034, #DATA1 M056, #DATA2 ; If M012 = DATA0 and ; M034 = DATA1 and ; M035 = DATA2 and MEM MEM MEM MEM MEM MEM DAT DAT DAT DAT DAT DAT 0.12H 0.34H 0.56H 1.07H 1.28H 1.6FH 1010B 0101B 0110B 1001B 1100B 0011B
156
PD17016, 17017
13.6.4 Notes on detecting power failure by RAM judgement method The value of the data memory on application of supply voltage VDD is basically "undefined", and therefore, the following points (1) and (2) must be noted. (1) Data to be compared Where the number of bits of the data memory to be compared by the RAM judgement method is "n bits", the probability at which the value of the data memory coincides with the value to be compared on application of VDD is (1/2)n. This means that backup is judged at a probability of (1/2)n when a power failure is detected by the RAM judgement method. To lower this probability, as many bits as possible must be compared. Because the contents of the data memory on application of VDD are likely to be the same value such as "0000B" and "1111B", it is recommended to mix "0" and "1" as data to be compared, such a "1010B" and "0110B" to reduce the possibility of a wrong judgment. (2) Notes on program If VDD rises from the level at which the data memory contents may be destroyed as shown in Figure 1312, and even if the value of the data memory area to be compared is normal, the values of the other data memory areas may be destroyed. This is judged as backup if a power failure is detected by the RAM judgement method. Therefore, consideration must be given so that the program does not hang up even if the contents of the data memory are destroyed. Figure 13-12. VDD and Destruction of Data Memory Contents
5V VDD Data memory destruction start voltage 0V
Data memory
Data memory for RAM judgement (normal) Values of data memory areas not used for RAM judgement may be destroyed.
157
PD17016, 17017
14. PLL FREQUENCY SYNTHESIZER
The PLL (Phase Locked Loop) frequency synthesizer is used to lock the frequency in the MF (Medium Frequency), HF (High Frequency), and VHF (Very High Frequency) bands to a specific frequency by comparing phase differences.
14.1 Configuration of PLL Frequency Synthesizer
Figure 14-1 shows the block diagram of the PLL frequency synthesizer. As shown in the figure, the PLL frequency synthesizer consists of an input select block, programmable divider (PD), phase comparator (-DET), reference frequency generator (RFG), and charge pump. By connecting these blocks with an external lowpass filter (LPF) and voltage-controlled oscillator (VCO), a PLL frequency synthesizer is organized. Figure 14-1. Block Diagram of PLL Frequency Synthesizer
Control register
Data buffer Unlock detection block Programmable divider (PD) Phase comparator ( -DET)
Input select block
Charge pump
VCOH VCOL
Reference frequency generator (RFG) Note Voltage-controlled oscillator (VCO) Lowpass filter (LPF) Note
EO1 EO0
Note
External circuit
158
PD17016, 17017
14.2 Functional Outline of PLL Frequency Synthesizer
The PLL frequency synthesizer divides a signal input from the VCOH (pin 32) or VCOL (pin 31) pin by using the programmable divider and outputs a phase difference from the reference frequency from the EO1 and EO0 pins. The PLL frequency synthesizer operates only when the CE pin is high, and is disabled when the CE pin is low. For the details on the disable status of the PLL frequency synthesizer, refer to 14.6. The following subsections 14.2.1 through 14.2.6 outline the function of each block of the PLL frequency synthesizer. 14.2.1 Input select block This block selects the pin from which a signal output from an external voltage-controlled oscillator is input. As the input pin, the VCOH or VCOL pin is selected by the PLL mode select register (RF address 21H). For details, refer to 14.3. 14.2.2 Programmable divider The programmable divider divides the signal input from the VCOH or VCOL pin at the division ratio set by the program. Two types of division modes can be selected: direct division and pulse swallow modes. The division mode is selected by the PLL mode select register. The division ratio is set by the PLL data register (PLLR: peripheral address 41H) via the data buffer. For details, refer to 14.3. 14.2.3 Reference frequency generator This generator generates a reference frequency to be compared by the phase comparator. Twelve types of reference frequencies can be selected by using the PLL reference mode select register (RF address 31H). For details, refer to 14.4. 14.2.4 Phase comparator and unlock detection block The phase comparator compares the division signal output by the programmable divider with the signal from the reference frequency generator, and outputs a phase difference. The unlock detection block detects the unlock status of the PLL. The unlock status of the PLL is detected by the PLL unlock FF judge register (RF address 05H). For details, refer to 14.5. 14.2.5 Charge pump The charge pump outputs the signal output by the phase comparator to the EO1 an EO0 pins as a high-level, low-level, or floating signal. For details, refer to 14.5.
159
PD17016, 17017
14.3 Input Select Block and Programmable Divider
14.3.1 Configuration of input select block and programmable divider Figure 14-2 shows the configuration of the input select block and programmable divider. As shown in the figure, the input select block consists of the VCOH and VCOL pins, and the amplifiers of the respective pins. The programmable divider consists of a 2-modulus prescaler, swallow counter, programmable counter, and division mode select switch. Figure 14-2. Configuration of Input Select Block and Programmable Divider
Control register Address Bit Flag symbol b3 P L L M D 3 21H b2 P L L M D 2 b1 P L L M D 1 b0 P L L M D 0 Address Symbol Data
Data buffer (DBF) 0CH DBF3 M S B 16 0DH DBF2 0EH DBF1 0FH DBF0 L S B Peripheral address 41H
2-4 decoder
PLL data register 12 bits 4 bits
PSC MF VHF VCOH VHF HF 2-modulus prescaler 1/16, 1/17
12
4
VHF HF
Swallow counter 4 bits Programmable counter 12 bits fN To -DET
MF
VCOL MF HF PLL disable signal
160
PD17016, 17017
14.3.2 Functions of input select block and programmable divider The input select block and programmable divider selects the input pin and division mode of the PLL frequency synthesizer. As the input pin, the VCOH or VCOL pin can be selected. The selected pin goes into an intermediate-potential state (approx. 1/2 VDD). The pin not selected is internally pulled down. These pins input signals via an AC amplifier, and the DC component of the input signal must be cut off by connecting a capacitor to the pin in series. Either the direct division mode or pulse swallow mode can be selected as the division mode. The programmable counter divides the signal input from the VCOH or VCOL pin in a specified division mode according to the values set to the swallow counter and programmable counter. Table 14-1 show the input pins (VCOH and VCOL) and division modes. The input pin and division mode to be used are selected by the PLL mode select register. 14.3.3 explains the configuration and function of the PLL mode select register. The division ratio is set to the programmable divider by the PLL data register via the data buffer. 14.3.4 explains the programmable divider and PLL data register. Table 14-1. Input Pins and Division Modes
Division Mode Pin Input Frequency (MHz) 0.5-30 Input Amplitude (Vp-p) 0.2 Settable Division Ratio 16 to 212 - 1 256 to 216 - 1 256 to 216 - 1 ---------------------------Division Ratio Settable in Data Buffer
Direct division (MF) Pulse swallow (HF) Pulse swallow (VHF)
VCOL
010xH-FFFxH (x: low-order 4 bits are don't care) 0100H-FFFFH
VCOL
5-40
0.2
VCOH
9-150
0.2
0100H-FFFFH
161
PD17016, 17017
14.3.3 Configuration and function of PLL mode select register The PLL mode select register specifies the division mode of the PLL frequency synthesizer and the pin to be used. The configuration and function of the PLL mode select register are shown below. The paragraphs (1) through (4) below outlines the respective division modes.
Name b3 PLL mode select register P L L M D 3
Flag symbol b2 P L L M D 2 b1 P L L M D 1 b0 P L L M D 0
Address
Read/ Write
21H
R/W
Sets division mode of PLL frequency synthesizer 0 0 1 1 0 1 0 1 Disables VCOL and VCOH pins Direct division mode (VCOL pin, MF mode) Pulse swallow (VCOH pin, VHF mode) Pulse swallow (VCOL pin, HF mode)
Fixed to "0"
On reset
Power-ON Clock stop CE
0
0
0 0
0 0
Retained
(1) Direct division mode (MF) In this mode, the VCOL pin is used. The VCOH pin is pulled down. In the direct division mode, the frequency of the input signal is divided only by the programmable counter. (2) Pulse swallow mode (HF) The VOL pin is used in this mode. The VCOH pin is pulled down. In this mode, the frequency of the input signal is divided by the swallow counter and programmable counter. (3) Pulse swallow mode (VHF) The VCOH pin is used in this mode. The VCOL pin is pulled down. In this mode, the frequency of the input signal is divided by the swallow counter and programmable counter. (4) Disabling VCOL and VCOH pins The VCOH and VCOL pins are internally pulled down. However, the phase comparator, reference frequency generator, and charge pump operate. Therefore, the operation is different from that in the PLL disable status to be explained later.
162
PD17016, 17017
14.3.4 Programmable divider and PLL data register The programmable divider divides the signal input from the VCOH or VCOL pin by the value set to the swallow counter and programmable counter. The swallow counter and programmable counter are 4-bit binary down counters. The division ratio is set to the swallow counter and programmable counter by the PLL data register (PLLR: peripheral address 41H) via data buffer. Data is set to or read from the PLL data register by using the "PUT PLLR, DBF" or "GET DBF, PLLR" instruction. The value to be divided is called N value. For how to set the N value in each division mode, refer to 14.7. (1) PLL data register and data buffer The relation between the PLL data register and data buffer is explained next. In the direct division mode, the high-order 12 bits are valid, and all the 16 bit are valid in the pulse swallow mode. In the direct division mode, all the high-order 12 bits are set to the programmable counter. In the pulse swallow mode, the high-order 12 bits are set to the programmable counter, and the low-order 4 bits are set to the swallow counter. (2) Relation between division value N and divided output frequency The relation between the value "N" set to the PLL data register and the frequency "fN" of the signal divided and output by the programmable divider is as follows. For details, refer to 14.7. (a) In direct division mode (MF) fIN N
fN =
N: 12 bits
(b) In pulse swallow mode (HF and VHF) fIN N
fN =
N: 16 bits
163
PD17016, 17017
Name Symbol Address Bit Data b3 DBF3 0CH b2 b1 b0 b3 DBF2 0DH b2 b1 b0 b3 Data buffer DBF1 0EH b2 b1 b0 b3 DBF0 0FH b2 b1 b0
Transfer data
GET can be executed 16 PUT can be executed Peripheral register Name PLL data register b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0 Symbol PLLR Valid data
Peripheral address
Peripheral address PLL frequency synthesizer
41H
Sets division ratio of PLL frequency synthesizer Direct division mode 0 Don't care Setting prohibited
15 (00FH) 16 (010H)
Don't care Don't care Division ratio N: N = x
x
Don't care
212 -1 (FFFH) Pulse swallow mode 0
Don't care Setting prohibited
255 (00FFH) 256 (0100H) Division ratio N: N = x
x
216 -1 (FFFFH)
164
PD17016, 17017
14.4 Reference Frequency Generator
14.4.1 Configuration and function of reference frequency generator Figure 14-3 shows the configuration of the reference frequency generator. As shown in the figure, the reference frequency generator divides 4.5 MHz of the crystal oscillation circuit to generate the reference frequency "fr" of the PLL frequency synthesizer. Twelve reference frequencies can be selected: 1, 1.25, 2.5, 3, 5, 6.25, 9, 10, 12.5, 25, 50, and 100 kHz. Reference frequency fr is selected by the PLL reference mode select register. 14.4.2 shows the configuration and function of the PLL reference mode select register. Figure 14-3. Configuration of Reference Frequency Generator (RFG)
Control register Address Bit Flag symbol b3 P L L R F C K 3 31H b2 P L L R F C K 2 b1 P L L R F C K 1 b0 P L L R F C K 0
4-16 decoder PLL disable signal Divider 4.5 MHz 1 kHz 1.25 kHz 3 kHz To -DET 50 kHz 100 kHz MUX
165
PD17016, 17017
14.4.2 Configuration and function of PLL reference mode select register The configuration and function of the PLL reference mode select register are shown below.
Name b3 PLL reference mode select register P L L R F C K 3
Flag symbol b2 P L L R F C K 2 b1 P L L R F C K 1 b0 P L L R F C K 0
Address
Read/ Write
31H
R/W
Sets reference frequency fr of PLL frequency synthesizer 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 1.25 kHz 2.5 kHz 5 kHz 10 kHz 6.25 kHz 12.5 kHz 25 kHz 50 kHz 3 kHz Setting prohibited Setting prohibited Setting prohibited 1 kHz 9 kHz 100 kHz PLL disabled
On reset
Power-ON Clock stop CE
1 1
1 1
1 1
1 1
Retained
When the PLL is disabled by the PLL reference mode select register, the VCOH and VCOL pins are internally pulled down. The EO1 and EO0 pins are floated. For disabling the PLL, refer to 14.6.
166
PD17016, 17017
14.5 Phase Comparator (-DET), Charge Pump, and Unlock Detection Block
14.5.1 Configuration of phase comparator, charge pump, and unlock detection block Figure 14-4 shows the configuration of the phase comparator, charge pump, and unlock detection block. The phase comparator compares the divided frequency output "fN" of the programmable divider with the reference frequency output "fr" of the reference frequency generator, and outputs an up request (UP) or down request (DW) signal. The charge pump outputs the output of the phase comparator from the error out (EO1 and EO0) pins. The unlock detection block detects the unlock status of the PLL frequency synthesizer. The following subsections 14.5.2 through 14.5.4 respectively explain the operations of the phase comparator, charge pump, and unlock detection block. Figure 14-4. Configuration of Phase Comparator, Charge Pump, and Unlock Detection Block
Control register Address Bit Flag symbol b3 0 05H b2 0 b1 0 b0 P L L U L
Phase comparator ( -DET) fr UP
Unlock detection block
Reference frequency generator
Unlock FF
Charge pump VDD P-ch EO1 N-ch VDD Programmable divider fN DW P-ch EO0 N-ch
PLL disable signal
167
PD17016, 17017
14.5.2 Function of phase comparator As shown in Figure 14-4, the phase comparator compares the divided frequency output "fN" of the programmable divider with the reference frequency output "fr" of the reference frequency generator, and outputs an up request or down request signal. If the divided frequency fN is lower than the reference frequency fr, the phase comparator outputs the up request signal; if fN is higher than fr, it outputs the down request signal. Figure 14-5 shows the relation among the reference frequency fr, divided frequency fN, up request signal, and down request signal. When the PLL is disabled, neither the up request nor down request signal is output. The up request and down request signals are respectively input to the charge pump and unlock detection block. Figure 14-5. Relation among fr, fN, UP, and DW (a) If fN is behind fr in phase
fr fN UP DW
(b) If fN leads fr in phase
fr fN UP DW
(c) If fN and fr are in phase
fr fN UP DW
(d) If fN is lower than fr in frequency
fr fN UP DW
168
PD17016, 17017
14.5.3 Charge pump As shown in Figure 14-4, the charge pump outputs the up request signal or down request signal from the phase comparator to the error out (EO1 and EO0) pins. Therefore, the relation among the outputs of the error out pins, divided frequency fN, and reference frequency fr are as follows. When reference frequency fr > divided frequency fN: low-level output When reference frequency fr < divided frequency fN: high-level output When reference frequency fr = divided frequency fN: floating output
169
PD17016, 17017
14.5.4 Unlock detection block As shown in Figure 14-4, the unlock detection block detects the unlock status of the PLL frequency synthesizer by using the up request or down request signal from the phase comparator. Because either of the up request or down request signal outputs a low level in the unlock status, this lowlevel signal is used to detect the unlock status. In the unlock status, the unlock flip-flop (FF) is set to 1. The unlock status is detected by the PLL unlock FF judgement register (refer to 14.5.5). The unlock FF is set at the cycle of reference frequency fr selected at that time. When the contents of the PLL unlock FF judgement register are read (by the PEEK instruction), the unlock FF is reset (Read & Reset). Therefore, the unlock FF must be detected at a cycle longer than the cycle 1/fr of the reference frequency fr. 14.5.5 Configuration and function of unlock FF judgement register
Name b3 PLL unlock FF judgement register 0
Flag symbol b2 0 b1 0 b0 P L L U L
Address
Read/ Write
05H
R & Reset
Detects status of unlock FF 0 1 Unlock FF = 0 : PLL lock status Unlock FF = 1 : PLL unlock status
Fixed "0"
On reset
Power-ON Clock stop CE
0
0
0
Undefined Retained Retained
This register is a read-only register and is reset when its contents are read to the window register by the "PEEK" instruction. Because the unlock FF is set at the cycle of reference frequency fr, the contents of the PLL unlock FF judgement register must be written to the window register at a cycle longer than the cycle 1/fr of the reference frequency fr.
170
PD17016, 17017
14.6 PLL Disabled Status
The PLL frequency synthesizer stops operation (is disabled) while the CE pin (pin 13) is low. When the PLL is disabled by the PLL reference mode select register, the PLL frequency synthesizer also stops operation. Table 14-2 shows the operation of each block under each PLL disable condition. When the VCOL and VCOH pins are disabled by the PLL mode select register, only the VCOL and VCOH pins are internally pulled down, and the other blocks operate. Because the PLL reference mode select register and PLL mode select register are not initialized (but hold the previous status) on CE reset, they are restored to the original status when the CE pin has once gone low and then back high again after the PLL has been disabled. To disable the PLL on CE reset, therefore, initialize these registers in the program. The PLL is disabled at power-ON reset. Table 14-2. Operation of Blocks Under PLL Disable Conditions
Condition CE Pin = Low Level (PLL disabled) Blocks VCOL and VCOH pins Programmable counter Reference frequency generator Phase comparator Charge pump Stops output Stops output Operates Internally pulled down CE Pin = High Level PLL reference mode select register = 1111B (PLL disabled) Internally pulled down PLL mode select register = 0000B (VCOH, VCOL disabled) Internally pulled down
Stops division
Stops division
Operates
Stops output Floats error out pins
Stops output Floats error out pins
Operates Operates. However, usually outputs low level because there is no input.
14.7 Using PLL Frequency Synthesizer
To control the PLL frequency synthesizer, the following data are necessary. (1) Division mode (2) Pin used (4) Division ratio : direct division (MF), pulse swallow (HF, VHF) : VCOL, VCOH :N
(3) Reference frequency: fr
The following subsections 14.7.1 through 14.7.3 explain how to set the PLL data in each division mode (MF, HF, and VHF).
171
PD17016, 17017
14.7.1 Direct division mode (1) Selecting division mode Select the direct division mode by using the PLL mode select register. (2) Pin used When the direct division mode is selected, the VCOL pin is enabled to operate. (3) Setting reference frequency fr Set the reference frequency by using the PLL reference mode select register. (4) Calculating division value N Calculate as follows: fVCOL fr
N=
where, fVCOL : input frequency of VCOL pin fr : reference frequency
(5) Example of setting PLL data How to set the data to receive broadcasting in the following MW band is explained below. Reception frequency Reference frequency Division value N: fVCOL fr 1422 + 450 9 : 1422 kHz (MW band) : 9 kHz
Intermediate frequency : +450 kHz
N=
=
= 208 (decimal) = 0D0H (hexadecimal)
Set data to the PLL data register (PLLR: peripheral address 41H), PLL mode select register (RF address 21H), and PLL reference mode select register (RF address 31H) as follows.
PLL data register (RLLR)
PLL mode PLL reference select register mode select register 0 Don't care 00 0 1 11 0 1
0
0 0
0
0
11 D
0
1
00 0
0
MF
9 kHz
172
PD17016, 17017
14.7.2 Pulse swallow mode (HF) (1) Selecting division mode Select the pulse swallow mode by using the PLL mode select register. (2) Pin used When the pulse swallow mode is selected, the VCOL pin is enabled to operate. (3) Setting reference frequency fr Set the reference frequency by using the PLL reference mode select register. (4) Calculating division value N Calculate as follows: fVCOL fr
N=
where, fVCOL : input frequency of VCOL pin fr : reference frequency
(5) Example of setting PLL data How to set the data to receive broadcasting in the following SW band is explained below. Reception frequency Reference frequency Division value N: fVCOL fr 25500 + 450 5 : 25.50 MHz (SW band) : 5 kHz
Intermediate frequency : +450 kHz
N=
=
= 5190 (decimal) = 1446H (hexadecimal)
Set data to the PLL data register (PLLR: peripheral address 41H), PLL mode select register (RF address 21H), and PLL reference mode select register (RF address 31H) as follows.
PLL data register (RLLR) PLL mode PLL reference select register mode select register 0 01 6 1 0 00 1 HF 1 0 0 1 0
0
0 1
0
1
01 4
0
0
01 4
0
5 kHz
173
PD17016, 17017
14.7.3 Pulse swallow mode (VHF) (1) Selecting division mode Select the pulse swallow mode by using the PLL mode select register. (2) Pin used When the pulse swallow mode is selected, the VCOH pin is enabled to operate. (3) Setting reference frequency fr Set the reference frequency by using the PLL reference mode select register. (4) Calculating division value N Calculate as follows: fVCOH fr
N=
where, fVCOH: input frequency of VCOH pin fr : reference frequency
(5) Example of setting PLL data How to set the data to receive broadcasting in the following FM band is explained below. Reception frequency Reference frequency Division value N: fVCOH fr 100.0 + 10.7 0.025 : 100.0 MHz (FM band) : 25 kHz
Intermediate frequency : +10.7 MHz
N=
=
= 4428 (decimal) = 114CH (hexadecimal)
Set data to the PLL data register (PLLR: peripheral address 41H), PLL mode select register (RF address 21H), and PLL reference mode select register (RF address 31H) as follows.
PLL data register (RLLR)
PLL mode PLL reference select register mode select register 0 11 C 1 0 00 1 0 0 1 1 0
0
0 1
0
1
00 1
0
1
01 4
0
VHF
25 kHz
174
PD17016, 17017
14.8 Status on Reset
14.8.1 On power-ON reset The PLL is disabled on power-ON reset because the PLL reference mode select register is initialized to 1111B. 14.8.2 On execution of clock stop instruction The PLL is disabled when the CE pin goes low. 14.8.3 On CE reset (1) CE reset after execution of clock stop instruction The PLL is disabled because the PLL reference mode select register is initialized to 1111B by the clock stop instruction. (2) CE reset without clock stop instruction executed Because the PLL reference mode select register retains the previous status, the previous status is restored as soon as the CE pin has gone high. 14.8.4 In halt status The set status is retained if the CE pin is high.
175
PD17016, 17017
15. GENERAL-PURPOSE PORT
The general-purpose ports output a high-level, low-level, or floating signal to an external circuit, and read a high-level or low-level signal from the external circuit.
15.1 Configuration and Classification of General-Purpose Ports
Figure 15-1 shows the block diagram of the general-purpose ports. Table 15-1 classifies the general-purpose ports. As shown in Figure 15-1, the general-purpose ports include ports 0A (P0A) through 2A (P2A) to which are set by addresses 70H through 73H (port registers) of each bank of the data memory, and ports 0E (P0E) and 0F (P0F) to which data are set by addresses 6BH and 6DH of bank 0 of the data memory. Each port consists of general-purpose port pins (e.g., port 0A consists of P0A3 through P0A0 pins). As shown in Table 15-1, the general-purpose ports are classified into input/output ports (I/O ports), inputonly ports (input ports), and output-only ports (output ports). The I/O ports are further subdivided into bit I/O ports that can be set in the input or output mode in 1-bit units (1-pin units) and group I/O ports that can be set in the input or output mode in 4-bit units (4-pin units).
176
PD17016, 17017
Figure 15-1. Block Diagram of General-Purpose Port
Column address 6789A
0 0 1 2 Row 3 address 4 5 6 7
1
2
3
4
5
B
C
D
E
F
Data memory Port register BANK0 6B 6D BANK1 BANK2 BANK3Note System register
Bit Bit Group I/O I/O I/O In Bit I/O Out Out In Out Out Out
Setting of data P 0 A P 0 B P 0 C P 0 D P 1 A P 1 B P 1 C P 1 D P 2 A Control register P 0 E P 0 F
Setting of I/O Example of pin configuration of P0A P0A3 Pin P0A2 Pin P0A1 Pin P0A0 Pin
Note
BANK3 is not provided on the PD17016.
177
PD17016, 17017
Table 15-1. Classification of General-Purpose Ports
Classification of General-Purpose Ports General-purpose ports I/O ports Bit I/O Ports Port 0A Port 0B Port 0C Port 0C Port 0D Port 1D Port 1B Port 1C Port 2A Port 0E Port 0F Port register Data Set by:
Group I/O Input port
Port register Port register
Output port
Port register
Port register (multiplexed with LCD segment register)
15.2 Functional Outline of General-Purpose Ports
The general-purpose output ports and the general-purpose I/O ports set in the output mode output a high or low level from the corresponding pins when data are set to the corresponding port register or port group register. The general-purpose input ports and the general-purpose I/O ports set in the input mode detect the level of the signals input to the corresponding pins by reading the contents of the corresponding port register. The general-purpose I/O ports are set in the input or output mode by the corresponding control register. In other words, these ports can be set in the input or output mode by program. P0A through P0D, P1A through P1D, and P2A are set in the general-purpose port mode on power-ON reset. P0E and P0F are used as LCD segment signal output pins on power-ON reset. To use these ports as generalpurpose output ports, the corresponding control registers must be set independently. The following subsections 15.2.1 through 15.2.4 explain the port registers, the function of the port group register, and the functional outline of each port.
178
PD17016, 17017
15.2.1 General-purpose port data register (port register) A port register sets output data of and reads the input data of the corresponding general-purpose port. Because the port registers are mapped on the data memory, they can be manipulated by any data memory manipulation instruction. Figure 15-2 shows the relation between a port register and the corresponding port pins. By setting data to the port register corresponding to the port pins set in the general-purpose output port mode, the output of each pin is set. By reading the contents of the port register corresponding to the port pins set in the general-purpose input port mode, the input status of each pin is detected. Table 15-2 shows the relation between each port (each pin) and port register. Figure 15-2. Relation between Port Register and Pins
Port register Bank Address Bit P P P P
3 2 1 0
n m b3 b2 b1 b0
Bit significance of port register Address of port register (e.g., 70H = A, 71H = B, 72H = C, 73H = D) Bank of port register " P " of Port
Reserved words are defined for the port registers by the assembler. Because these reserved words are defined in flag (bit) units, the assembler embedded macro instructions can be used. Note that data memory type reserved words are not defined for the port registers. P0E and P0F are multiplexed with LCD segment signal output pins. The port registers of P0E and P0F are also multiplexed with LCD segment registers. Because the LCD segment registers are also mapped on the data memory, they can be treated in the same manner as the port registers.
179
PD17016, 17017
15.2.2 General-purpose I/O ports (P0A, P0B, P0C, and P1A) P0A, P0B, P0C, and P1A can be set in the input or output mode by the P0A bit I/O select register (RF address 37H), P0B bit I/O select register (RF address 36H), P0C group I/O select register (RF address 27H), P1A bit I/O select register (RF address 35H), respectively. The input/output data of the P0A, P0B, P0C, and P1A are set by port registers P0A (address 70H of BANK0), P0B (address 71H of BANK0), P0C (address 72H of BANK0), and P1A (address 70H of BANK1), respectively. Refer to Table 15-2. For details, refer to 15.3. 15.2.3 General-purpose input ports (P0D and P1D) The input data of P0D and P1D are read by port registers P0D (address 73H of BANK0) and P1D (address 73H of BANK1), respectively. Refer to Table 15-2. For details, refer to 15.4. 15.2.4 General-purpose output ports (P1B, P1C, P2A, P0E, and P0F) (1) P1B, P1C, and P2A The output data of P1B, P1C, and P2A are set by port registers P1B (address 71H of BANK1), P1C (address 72H of BANK1), and P2A (address 70H of BANK2). Refer to Table 15-2. For details, refer to 15.5. (2) P0E and P0F P0E and P0F usually operate as LCD segment signal output pins. These ports can be set in the output port mode by using a software macro supplied with the device file. To set the output data of P0E and P0F, P0E register (multiplexed with LCD segment register LCDD13, address 6DH of BANK0) and P0F register (multiplexed with LCDD11, address 6BH of BANK0) are used, respectively. Refer to Table 15-2. For details, refer to 15.6.
180
PD17016, 17017
Table 15-2. Relation between Each Port (Pin) and Port Register (1/2)
Port No. Pin Symbol I/O Bank Setting of Data Port register (data memory) Address Symbol Bit symbol (reserved word) b3 P0A3 --------------b2 P0A2 --------------b1 P0A1 --------------b0 P0A0 b3 P0B3 --------------b2 P0B2 --------------b1 P0B1 --------------b0 P0B0 b3 P0C3 --------------b2 P0C2 --------------b1 P0C1 --------------b0 P0C0 b3 P0D3 --------------b2 P0D2 --------------b1 P0D1 --------------b0 P0D0 b3 P1A3 --------------b2 P1A2 --------------b1 P1A1 --------------b0 P1A0 b3 P1B3 --------------b2 P1B2 --------------b1 P1B1 --------------b0 P1B0 b3 P1C3 --------------b2 P1C2 --------------b1 P1C1 --------------b0 P1C0 b3 P1D3 --------------b2 P1D2 --------------b1 P1D1 --------------b0 P1D0 b3 P2A3 Nothing is allocated. --------------b2 P2A2 Cannot be used as data --------------b1 P2A1 memory. -----------------------------------------b0 P2A0 Remark
Port 0A (P0A)
3 P0A3 I/O ----------------4 P0A2 (bit I/O) ----------------5 P0A1 ----------------6 P0A0 7 P0B3 I/O ----------------8 P0B2 (bit I/O) ----------------9 P0B1 ----------------10 P0B0 79 P0C3 I/O ----------------80 P0C2 (group ----------------1 P0C1 I/O) ----------------2 P0C0 75 P0D3 Input ----------------76 P0D2 ----------------77 P0D1 ----------------78 P0D0 14 P1A3 I/O ----------------15 P1A2 (bit I/O) ----------------16 P1A1 ----------------17 P1A0 18 P1B3 Output ----------------19 P1B2 ----------------20 P1B1 ----------------21 P1B0 22 P1C3 Output ----------------23 P1C2 ----------------24 P1C1 ----------------25 P1C0 26 P1D3 Input ----------------27 P1D2 ----------------28 P1D1 ----------------29 P1D0 No target pins
BANK0
70H
P0A
Port 0B (P0B)
71H
P0B
Port 0C (P0C)
72H
P0C
Poer 0D (P0D)
73H
P0D
Port 1A (P1A)
BANK1
70H
P1A
Port 1B (P1B)
71H
P1B
Port 1C (P1C)
72H
P1C
Port 1D (P1D)
73H
P1D
Port 2A (P2A)
BANK2
70H
P2A
--------------------------42 P2A0 Output
181
PD17016, 17017
Table 15-2. Relation between Each Port (Pin) and Port Register (2/2)
Port No. Pin Symbol I/O Bank Setting of Data Port register (data memory) Address Symbol Bit symbol (reserved word) b3 b2 b1 b0 72H - b3 b2 b1 b0 73H - b3 b2 b1 b0 BANK3Note 70H - b3 b2 b1 b0 71H - b3 b2 b1 b0 72H - b3 b2 b1 b0 73H - b3 b2 b1 b0 Port 0E (P0E) 49 P0E3 Output ----------------50 P0E2 ----------------51 P0E1 ----------------52 P0E0 45 P0F3 Output ----------------46 P0F2 ----------------47 P0F1 ----------------48 P0F0 BANK0 6BH P0E b3 P0E3 --------------b2 P0E2 --------------b1 P0E1 --------------b0 P0E0 b3 P0F3 --------------b2 P0F2 --------------b1 P0F1 --------------b0 P0F0 - - - - Nothing is allocated. Cannot be used as data memory. - - - Nothing is allocated. Cannot be used as data memory. Remark
BANK2
71H
-
(multiplexed with LCDD11)
Port 0F (P0F)
6DH
P0F
(multiplexed with LCDD13)
Note
BANK3 is not provided on the PD17016.
182
PD17016, 17017
15.3 General-Purpose I/O Ports (P0A, P0B, P0C, and P1A)
15.3.1 Configuration of I/O ports The following paragraphs (1) through (3) indicate the configuration of the I/O ports. (1) P0A (P0A1 and P0A0 pins), P0B (P0B3, P0B2, P0B1, and P0B0 pins), P1A (P1A3, P1A2, P1A1, and P1A0 pins)
VDD
I/O select flag
Output latch
Write instruction
Port register (1 bit) VDD
1 0
Read instruction
RESET
(2) P0C (P0C3, P0C2, P0C1, and P0C0 pins)
VDD
I/O select flag
Output latch
Write instruction
Port register (1 bit) VDD
1 0
Read instruction
183
PD17016, 17017
(3) P0A (P0A3 and P0A2 pins)
I/O select flag
Output latch
Write instruction
Port register (1 bit) VDD
Read instruction
RESET
15.3.2 Using I/O ports The I/O ports are set in the input or output mode by I/O select registers P0A P0B, P0C, and P1A of the control registers. The bit I/O ports (P0A, P0B, and P1A) can be set in the input or output mode in 1-bit units, and group I/O port (P0C) can be set in the input or output mode in 4-bit units. Output data can be set to a port by writing the data to the corresponding port register, and the input data of the port can be read by executing an instruction that reads the port register. 15.3.3 explains the I/O select register of each port. 15.3.4 and 15.3.5 explain how to use the input and output ports. 15.3.6 explains the points to be noted in using the I/O ports.
184
PD17016, 17017
15.3.3 Port 0A bit I/O select register Port 0B bit I/O select register Port 1A bit I/O select register Port 0C group I/O select register The port 0A bit I/O, port 0B bit I/O, port 1A bit I/O, and port 0C group I/O select registers sets each pin of the P0A, P0B, P1A, and P0C in the input or output mode. The configuration and functions of these registers are shown below. (1) Port 0A bit I/O select register
Name b3 Port 0A bit I/O select register P 0 A B I O 3
Flag symbol b2 P 0 A B I O 2 b1 P 0 A B I O 1 b0 P 0 A B I O 0
Address
Read/ Write
37H
R/W
Sets input or output mode of port 0 1 Sets P0A0 pin in input mode. Sets P0A0 pin in output mode.
Sets input or output mode of port 0 1 Sets P0A1 pin in input mode. Sets P0A1 pin in output mode.
Sets input or output mode of port 0 1 Sets P0A2 pin in input mode. Sets P0A2 pin in output mode.
Sets input or output mode of port 0 1 Sets P0A3 pin in input mode. Sets P0A3 pin in output mode.
On reset
Power-ON Clock stop CE
0 0 0
0 0 0
0 0 0
0 0 0
185
PD17016, 17017
(2) Port 0B bit I/O select register
Name b3 Port 0B bit I/O select register P 0 B B I O 3
Flag symbol b2 P 0 B B I O 2 b1 P 0 B B I O 1 b0 P 0 B B I O 0
Address
Read/ Write
36H
R/W
Sets input or output mode of port 0 1 Sets P0B0 pin in input mode. Sets P0B0 pin in output mode.
Sets input or output mode of port 0 1 Sets P0B1 pin in input mode. Sets P0B1 pin in output mode.
Sets input or output mode of port 0 1 Sets P0B2 pin in input mode. Sets P0B2 pin in output mode.
Sets input or output mode of port 0 1 Sets P0B3 pin in input mode. Sets P0B3 pin in output mode.
On reset
Power-ON Clock stop CE
0 0 0
0 0 0
0 0 0
0 0 0
186
PD17016, 17017
(3) Port 1A bit I/O select register
Name b3 Port 1A bit I/O select register P 1 A B I O 3
Flag symbol b2 P 1 A B I O 2 b1 P 1 A B I O 1 b0 P 1 A B I O 0
Address
Read/ Write
35H
R/W
Sets input or output mode of port 0 1 Sets P1A0 pin in input mode. Sets P1A0 pin in output mode.
Sets input or output mode of port 0 1 Sets P1A1 pin in input mode. Sets P1A1 pin in output mode.
Sets input or output mode of port 0 1 Sets P1A2 pin in input mode. Sets P1A2 pin in output mode.
Sets input or output mode of port 0 1 Sets P1A3 pin in input mode. Sets P1A3 pin in output mode.
On reset
Power-ON Clock stop CE
0 0 0
0 0 0
0 0 0
0 0 0
187
PD17016, 17017
(4) Port 0C group I/O select register
Name b3 Port 0C group I/O select register 0
Flag symbol b2 0 b1 0 b0 P 0 C G I O
Address
Read/ Write
27H
R/W
Sets input or output mode of port 0 1 Sets P0C3-P0C0 pin in input mode. Sets P0C3-P0C0 pin in output mode.
Fixed to "0"
On reset
Power-ON Clock stop CE
0
0
0
0 0 0
188
PD17016, 17017
15.3.4 Using I/O ports (P0A, P0B, P0C, and P1A) as input ports Select the pin that is used as an input port pin by the I/O select register corresponding to each port. Note that P0C can be set in the input or output mode in 4-bit units only. The pin specified as an input port pin is floated (Hi-Z), and waits for input of an external signal. The input data can be read by executing an instruction that reads the contents of the port register corresponding to each port, such as "SKT" instruction. When a high level is input to each pin, "1" is read to the corresponding port register; when a low level is input, "0" is read. If a write instruction, such as "MOV", is executed to the port register corresponding to the port pin specified as an input port pin, the contents of the output latch are rewritten. 15.3.5 Using I/O ports (P0A, P0B, P0C, and P1A) as output ports Select the pin that is used as an output port pin by the I/O select register corresponding to each port. Note that P0C can be set in the input or output mode in 4-bit units only. The pin specified as an output port pin outputs the contents of the output latch. The output data can be set by executing an instruction that writes the contents of the corresponding port register to each pin, such as "MOV" instruction. To output a high level to each pin, write "1" to the corresponding port register; to output a low level, write "0". The port pin can also be floated when it is specified as an input port pin. When an instruction, such as "SKT", that reads the contents of the port register corresponding to a port specified as an output port is executed, the contents of the output latch are read. Note, however, that the statuses of the P0A3 and P0A2 pins are read as is, and the read contents may be different from the contents of the output latch. Refer to 15.3.6.
189
PD17016, 17017
15.3.6 Notes on using I/O ports (P0A3 and P0A2 pins) When using the P0A3 and P0A2 pins as output pins, the contents of the output latch may be rewritten, as shown in the example below. Example To specify P0A3 and P0A2 pins as output port pins INITFLG P0ABI03, P0ABI02, NOT P0ABI01, NOT P0ABI00 ; Sets P0A3 and P0A2 pins in output mode INITFLG P0A3, P0A2, NOT P0A1, NOT P0A0 ; Outputs high level to P0A3 and P0A2 pins ;<1> CLR1 AND P0A3 ; Outputs low level to P0A3 pin Macro expansion . MF. P0A3 SHR 4, # .DF. (NOT P0A3 AND 0FH)
If the P0A2 pin happens to be lowered by an external device when the instruction in <1> above is executed, the contents of the output latch of the P0A2 pin are rewritten to "0" by the "CLR1" instruction. In other words, if an operation instruction (such as "ADD" and "OR") to the P0A port register when the P0A3 or P0A2 pin is set in the output mode, the contents of the output latch are rewritten to the current level of the pin, regardless of the previous status of the pin. 15.3.7 Status of I/O ports (P0A, P0B, P0C, and P1A) on reset (1) On power-ON reset All the I/O ports are set in the input mode. Because the contents of the output latch are "undefined", the output latch must be initialized by program, as necessary, before setting the corresponding port in the output mode. (2) On CE reset All the I/O ports are set in the input mode. The contents of the output latch are retained. (3) On execution of clock stop instruction All the I/O ports are set in the input mode. The contents of the output latch are retained. The I/O ports other than P0C prevents an increase in the current dissipation due to the noise of the input buffer by using the RESET signal when the clock stop instruction is executed, as explained in 15.3.1. If P0C is floated on execution of the clock stop instruction, the current dissipation may increase due to external noise. Externally pull this port down or up as necessary. (4) In halt status The previous status is retained.
190
PD17016, 17017
15.4 General-Purpose Input Ports (P0D and P1D)
15.4.1 Configuration of input ports The following paragraphs (1) and (2) indicate the configuration of the input ports. (1) P0D (P0D3, P0D2, P0D1, and P0D0 pins)
To A/D converter Write instruction
VDD
Port register (1 bit)
Input latch
Read instruction
High ON resistance
ADC select signal Key source signal timing output RESET
(2) P1D (P1D3, P1D2, P1D1, and P1D0 pins)
To frequency counter or A/D converter Write instruction
VDD
Port register (1 bit)
Read instruction
RESET
191
PD17016, 17017
15.4.2 Using input ports (P0D and P1D) The input data is read by executing an instruction, such as "SKT", that reads the contents of the port register corresponding to each port pin. When a high level is input to each pin, "1" is read to the corresponding port register; when a low level is input, "0" is read. Nothing is changed even if a write instruction, such as "MOV", is executed to the port register. 15.4.3 Notes on using input port (P0D) The P0D is internally pulled down when it is used as a general-purpose port. 15.4.4 Status of input ports (P0D and P1D) on reset (1) On power-ON reset All the input ports are specified as general-purpose input ports. (2) On CE reset All the input ports are specified as general-purpose input ports. (3) On execution of clock stop instruction All the input ports are specified as general-purpose input ports. Because the RESET signal is output when the clock stop instruction is executed, the P1D prevents an increase in the current dissipation due to the noise of the input buffer. The P0D is internally pulled down. (4) In halt status The previous status is retained.
192
PD17016, 17017
15.5 General-Purpose Output Ports (P1B, P1C, and P2A)
15.5.1 Configuration of output ports (P1B, P1C, and P2A) The following paragraphs (1) and (2) indicate the configuration of the output ports. (1) P1B (P1B0 pin), P1C (P1C3, P1C2, P1C1, and P1C0 pins), P2A (P2A0 pin)
VDD Output latch Write instruction
Port register (1 bit)
Read instruction
(2) P1B (P1B3, P1B2, and P1B1 pins)
Output latch
Write instruction
Port register (1 bit)
Read instruction
193
PD17016, 17017
15.5.2 Example of using output ports (P1B, P1C, and P2A) The output ports output the contents of the output latches. The output data is set by executing an instruction, such as "MOV", that writes the data to the port register corresponding to the output port. Write "1" to the port register to output a high level to the corresponding port; write "0" to output a low level. Note, however, that the P1B3, P1B2, and P1B1 pins are N-ch open-drain output pins and are floated when a high level is output. When an instruction, such as "SKT", that reads the contents of the port register is read, the contents of the output latch are read. 15.5.3 Status of output ports (P1B, P1C, and P2A) on reset (1) On power-ON reset The contents of the output latch are output. Because the contents of the output latch are "undefined", an "undefined" value is output for a fixed period (until the output latch is initialized by program). (2) On CE reset The contents of the output latch are output. The contents of the output latch are retained and the output data are not changed on CE reset. (3) On execution of clock stop instruction The contents of the output latch are output. The contents of the output latch are retained and the output data are not changed on execution of the clock stop instruction. Therefore, initialize the output latch in the program as necessary. (4) In halt status The contents of the output latch are output. The contents of the output latch are retained and the output data are not changed in the halt status.
194
PD17016, 17017
15.6 General-Purpose Output Ports (P0E and P0F)
15.6.1 Configuration of output ports (P0E and P0F) The configuration of the output ports is shown below. P0E (P0E3, P0E2, P0E1, and P0E0 pins) P0F (P0F3, P0F2, P0F1, and P0F0 pins)
LCD/port select flag
VDD
1 0
Output latch Segment signal timing control
Write instruction
Port register (1 bit) multiplexed with LCD segment register
Read instruction
15.6.2 Example of using output ports (P0E and P0F) Each pin of the P0E and P0F are used as an LCD segment signal output pin on power-ON reset. To use it as an output port pin, select the port to be used by a software macro supplied with the device file. The port to be used can be selected independently. The pins not set in the output port mode can be used as LCD segment signal output pins. Table 15-3 shows the software macros that set the ports (P0E and P0F).
195
PD17016, 17017
Table 15-3. Software Macros Setting Ports (P0E and P0F)
Function Uses LCD22/P0E0-LCD25/P0E3 pins as general-purpose output port Uses LCD26/P0F0-LCD29/P0F3 pins as general-purpose output port Uses LCD22/P0E0-LCD25/P0E3 pins and LCD26/P0F0-LCD29/P0F3 pins as general-purpose output port Uses LCD22/P0E0-LCD25/P0E3 pins as LCD segment signal output pins Uses LCD26/P0F0-LCD29/P0F3 pins as LCD segment signal output pins Uses LCD22/P0E0-LCD25/P0E3 and LCD26/P0F0-LCD29/P0F3 pins as LCD segment signal output pins Uses LCD22/P0E0-LCD25/P0E3 pins as LCD segment signal output pins and LCD26/ P0F0LCD29/P0F3 pins as general-purpose output port Uses LCD22/P0E0-LCD25/P0E3 pins as general-purpose output port and LCD26/P0F0-LCD29/ P0F3 pins as LCD segment signal output pins Macro Format SET1_P0EON SET1_P0FON SET2_P0EON_P0FON
CLR1_P0EON CLR1_P0FON CLR2_P0EON_P0FON
INIT_NOT_P0EON_P0FON
INIT_P0EON_NOT_P0FON
Caution
If the above macros are used, the contents of the window register are destroyed. If the above macros are immediately follow an embedded macro instruction, an "object error" occurs when the source file is assembled and loaded to the in-circuit emulator. If an embedded macro is used before the above macros, insert a comment statement in between them.
15.6.3 Setting data to P0E and P0F Output data are set to the P0E and P0F by executing an instruction, such as "MOV", that writes data to the port registers corresponding to the ports. To output a high level to each port pin, write "1" to the corresponding port register; to output a low level, write "0". The contents of the output latch are read when an instruction, such as "SKT", that reads the contents of the port register is executed. Figure 15-3 shows the relation between the P0F port register and LCD segment register. As shown in this figure, LCD segment register LCDD14 can be used as a general-purpose data memory area when the P0F is used. The same applies to the P0E. Refer to Figure 21-6. Relation among LCD Display Dots, Ports 0E and 0F, Key Source Output, and Each Data Setting Register in 21. LCD CONTROLLER/DRIVER. Figure 15-3. Relation between P0F Port Register and LCD Segment Register
P0FON flag LCD29/P0F3 1 0 1 0 1 0 1 0
Segment signal timing control Segment signal timing control Segment signal timing control Segment signal timing control
b3 b2 b1 b0 b3 b2 b1 b0 LCDD14 (6EH)
LCD28/P0F2
LCD27/P0F1
LCD26/P0F0
LCDD13 P0F (6DH)
196
PD17016, 17017
15.6.4 Status of output ports (P0E and P0F) on reset (1) On power-ON reset The P0E and P0F are set as LCD segment signal output pins and output a low level. Because the contents of the output latch are undefined, undefined data is output if these ports are set in the output mode as is. Initialize the ports in the program as necessary. (2) On CE reset The P0E and P0F are set as LCD segment signal output pins and output a low level. Because the contents of the output latch are retained, the previous values are retained if these ports are set in the output mode as is. (3) On execution of clock stop instruction The P0E and P0F are set as LCD segment signal output pins and output a low level. Because the contents of the output latch are retained, the previous values are retained if these ports are set in the output mode as is. (4) In halt status The contents of the output latch are output. Because the contents of the output latch are retained, the output data are not changed in the halt status.
197
PD17016, 17017
16. A/D CONVERTER (ADC)
The A/D converter is used to input an external analog signal as a digital signal.
16.1 Configuration of A/D Converter
Figure 16-1 shows the block diagram of the A/D converter. As shown in the figure, the A/D converter consists of an input select block, compare voltage generation block, and compare block. Figure 16-1. Block Diagram of A/D Converter
Control register
Data buffer
P0D3/ADC5 P0D2/ADC4 P0D1/ADC3 P0D0/ADC2 P1D1/ADC1 P1D0/ADC0
6 Input select block Compare block
Compare voltage generation block (R-string D/A converter)
16.2 Functional Outline of A/D Converter
The A/D converter compares the voltage input to the P0D3/ADC5 to P1D0/ADC0 pin with an internal compare voltage, and outputs the result of the comparison as "True (1)" or "False (0)". By judging this comparison result by software, the A/D converter can be used as a successive approximation converter. The following subsections 16.2.1 through 16.2.3 outline the function of each block of the A/D converter. For details, refer to 16.3 through 16.5. 16.2.1 Input select block This block selects which of the P0D3/ADC5 through P1D0/ADC0 pins is to be used. The pin is selected by the A/D converter channel select register (RF address 14H). Only one pin can be selected at a time. Refer to 16.3. 16.2.2 Compare voltage generation block This block generates a compare voltage against which an input voltage is to be compared. The compare voltage is generated by an R-string D/A converter. Refer to 16.4.
198
PD17016, 17017
16.2.3 Compare block This block compares an input voltage with an internal compare voltage. The result of the comparison is detected by the A/D converter compare judge register (RF address 06H). Refer to 16.5.
16.3 Input Select Block
16.3.1 Configuration of input select block Figure 16-2 shows the configuration of the input select block. Figure 16-2. Configuration of Input Select Block
Control register Address Bit Flag symbol 14H b3 b2 b1 b0 A D C C H 3 A D C C H 2 A D C C H 1 A D C C H 0
3-6 decoder
P0D3/ADC5 P0D2/ADC4 P0D1/ADC3 P0D0/ADC2
0 1
To compare block VADCIN
High ON resistance (for key input) P1D1/ADC1 P1D0/ADC0
199
PD17016, 17017
16.3.2 Function of input select block The input select block selects a pin to be used by using the A/D converter channel select register. Only one pin can be used as an A/D converter pin at a time. The pin not selected for the A/D converter can be used as general-purpose input port. Although port 0D (P0D3/ADC5 through P0D0/ADC2 pins) is internally connected to a pull-down resistor, the pin selected by the A/D converter channel select register (refer to 16.3.3) is disconnected from the pull-down resistor as soon as it has been selected. The pins not selected remain connected to the pull-down resistor. 16.3.3 Configuration and function of A/D converter channel select register The A/D converter channel select register selects a pin to be used for the A/D converter. The configuration and function of this register are shown below.
Name b3 A/D converter channel select register A D C C H 3
Flag symbol b2 A D C C H 2 b1 A D C C H 1 b0 A D C C H 0
Address
Read/ Write
14H
R/W
Selects pin to be used for A/D converter 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 P1D0/ADC0 pin P1D1/ADC1 pin P0D0/ADC2 pin P0D1/ADC3 pin P0D2/ADC4 pin P0D3/ADC5 pin A/D converter is not used (general-purpose input port) A/D converter is not used (general-purpose input port)
Fixed to "0"
On reset
Power-ON Clock stop CE
0
1 1 1
1 1 1
1 1 1
200
PD17016, 17017
16.4 Compare Voltage Generation Block
16.4.1 Configuration of compare voltage generator block Figure 16-3 shows the configuration of the compare voltage generator block. Figure 16-3. Configuration of Compare Voltage Generator Block
Data buffer (DBF) Address Symbol Data 0CH DBF3 Don't care 0DH DBF2 Don't care M S B 6
A/D converter data register
0EH DBF1
0FH DBF0 L S B Peripheral address 02H To compare block VREF
Multiplexer 0 1 2 62 63
VDD
1 R 2
R
R
3 R 2
Reading ADCCMP flag by PEEK
16.4.2 Function of compare voltage generator block The compare voltage generator block switches the multiplexer according to the 6-bit data set to the A/D converter data register (ADCR: peripheral address 02H) and generates a compare voltage. This block is therefore an R-string D/A converter. The compare voltage can be adjusted in 64 steps by the R string (resistance division). The voltage supplied to the R string is the same as the supply voltage VDD of the device. The voltage is supplied to the resistor of the R string only when the A/D converter compare judge register, which is to be explained later, is detected. The compare voltage is compared with a voltage input to the compare block from a selected pin. 16.4.3 explains the configuration and function of the A/D converter data register. Table 16-1 lists the compare voltages.
201
PD17016, 17017
16.4.3 Configuration and function of A/D converter data register (ADCR) The A/D converter data register sets the compare voltage of the A/D converter. Because this register is 6 bits long, the low-order 6 bits of the data buffer are valid.
Name Symbol Address Bit Data b3 DBF3 0CH b2 b1 b0 b3 DBF2 0DH b2 b1
Data buffer DBF1 0EH b0 b3 b2 b1 b0 b3 DBF0 0FH b2 b1 b0
Don't care
Don't care
Transfer data
GET can be executed 8 PUT can be executed Peripheral register Name A/D converter data register b7 0 b6 0 Valid data b5 b4 b3 b2 b1 b0 Symbol ADCR
Peripheral address
Peripheral hardware A/D converter
02H
Sets compare voltage VREF of A/D converter 0 1 VREF = VREF = 0 V x - 0.5 x VDD V 64
x
63
Fixed to "0"
202
PD17016, 17017
Table 16-1. Set Values of A/D Converter Data Register and Compare Voltages
Set Data of ADCR Decimal (DEC) 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Hexadecimal (HEX) 00H 01H 02H 03H 04H 05H 06H 07H 08H 09H 0AH 0BH 0CH 0DH 0EH 0FH 10H 11H 12H 13H 14H 15H 16H 17H 18H 19H 1AH 1BH 1CH 1DH 1EH 1FH Compare Voltage Logic voltage Unit: x VDD V 0 0.5/64 1.5/64 2.5/64 3.5/64 4.5/64 5.5/64 6.5/64 7.5/64 8.5/64 9.5/64 10.5/64 11.5/64 12.5/64 13.5/64 14.5/64 15.5/64 16.5/64 17.5/64 18.5/64 19.5/64 20.5/64 21.5/64 22.5/64 23.5/64 24.5/64 25.5/64 26.5/64 27.5/64 28.5/64 29.5/64 30.5/64 At VDD = 5 V Unit: V 0 0.039 0.117 0.195 0.273 0.352 0.430 0.508 0.586 0.664 0.742 0.820 0.898 0.977 1.055 1.133 1.211 1.289 1.367 1.445 1.523 1.602 1.680 1.758 1.836 1.914 1.992 2.070 2.148 2.227 2.305 2.383 Set Data of ADCR Decimal (DEC) 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 Hexadecimal (HEX) 20H 21H 22H 23H 24H 25H 26H 27H 28H 29H 2AH 2BH 2CH 2DH 2EH 2FH 30H 31H 32H 33H 34H 35H 36H 37H 38H 39H 3AH 3BH 3CH 3DH 3EH 3FH Compare Voltage Logic voltage Unit: x VDD V 31.5/64 32.5/64 33.5/64 34.5/64 35.5/64 36.5/64 37.5/64 38.5/64 39.5/64 40.5/64 41.5/64 42.5/64 43.5/64 44.5/64 45.5/64 46.5/64 47.5/64 48.5/64 49.5/64 50.5/64 51.5/64 52.5/64 53.5/64 54.5/64 55.5/64 56.5/64 57.5/64 58.5/64 59.5/64 60.5/64 61.5/64 62.5/64 At VDD = 5 V Unit: V 2.461 2.539 2.617 2.695 2.773 2.852 2.930 3.008 3.086 3.164 3.242 3.320 3.398 3.477 3.555 3.633 3.711 3.789 3.867 3.945 4.023 4.102 4.180 4.258 4.336 4.414 4.492 4.570 4.648 4.727 4.805 4.883
203
PD17016, 17017
16.5 Compare Block
16.5.1 Configuration of compare block Figure 16-4 shows the configuration of the compare block. Figure 16-4. Configuration of Compare Block
Control register Address Bit Flag symbol b3 0 06H b2 0 b1 0 b0 A D C C M P
1 VDD 2
Switch 2 Switch 1 VADCIN 2 pF VREF - Comparator + Compare judge FF
16.5.2 Function of compare block The compare block compares the voltage VADCIN input from a pin with the internal compare voltage VREF by using a comparator and outputs the result of the comparison to the compare judge FF. The compare judge FF can be detected by reading the ADCCMP flag of the A/D converter compare judge register. The ADCCMP flag is set when VADCIN > VREF and reset when VADCIN < VREF. The comparator performs comparison when the ADCCMP flag has been read. In other words, when the ADCCMP flag has been read by using the "PEEK" instruction, comparison is performed by manipulating switches 1 and 2. Therefore, the time required for the A/D converter to perform comparison once is equal to one instruction execution time (4.44 s). 16.5.3 explains the configuration and function of the A/D converter compare judge register.
204
PD17016, 17017
16.5.3 Configuration and function of A/D converter compare judge register The A/D converter compare judge register detects the result of comparison between input voltage VADCIN and compare voltage VREF. The configuration and function of this register are illustrated below.
Name b3 A/D converter compare judge register 0
Flag symbol b2 0 b1 0 b0 A D C C M P
Address
Read/ Write
06H
R
Detects result of comparison by A/D converter 0 1 VADCIN < VREF VADCIN > VREF
Fixed to "0"
On reset
Power-ON Clock stop CE
0
0
0
Undefined Retained Retained
16.6 Performances of A/D Converter
The performances of the A/D converter are as follows.
Parameter Resolution Input voltage range Quantization error Performance 1LSB 0-VDD 1 LSB 2
Over range
62.5 x VDD 64 3 LSBNote 2
Error of offset, gain, and non-linearity
Note
Including quantization error.
205
PD17016, 17017
16.7 Using A/D Converter
16.7.1 Comparing one compare voltage Here is a program example. Example To compare input voltage VADCIN of ADC0 pin with compare voltage VREF (31.5/64 VDD) and branch to AAA if VADCIN > VREF or to BBB if VADCIN < VREF INIT: ADCR7 ADCR6 ADCR5 ADCR4 ADCR3 ADCR2 ADCR1 ADCR0 CLR3 START: INITFLG NOT ADCR3, NOT ADCR2, NOT ADCR1, NOT ADCR0 INITFLG NOT ADCR7, NOT ADCR6, PUT SKT1 BR BR ADCR, DBF ADCCMP AAA BBB ADCR5, NOT ADCR4 ; Sets compare voltage VREF to 31.5/64 VDD ; Detects ADCCMP flag, and ; branches to AAA if False (0) ; branches to BBB if True (1) FLG FLG FLG FLG FLG FLG FLG FLG 0.0EH.3 0.0EH.2 0.0EH.1 0.0EH.0 0.0FH.3 0.0FH.2 0.0FH.1 0.0FH.0 ; Dummy ; Dummy ; Defines each bit of data buffer as ADCR data setting ; flag
ADCCH2, ADCCH1, ADCCH0 ; Sets P1D0/ADC0 pin for the A/D converter
206
PD17016, 17017
16.7.2 Successive approximation by binary search method The A/D converter can compare only one voltage at one time. To convert an input voltage into a digital signal, therefore, successive approximation must be executed by program. If the processing time of the successive approximation program differs depending on the input voltage, the relation with the other processing programs is undesirable. Therefore, use of the binary search method as explained in (1) through (3) below is recommended. (1) Concept of binary search The concept of binary search is explained below. First, the compare voltage is set to 1/2 VDD. If the result of comparison is True (a high level is input), a voltage of 1/4 VDD is added to the result; if the result of comparison is False (a low level is input), a voltage of 1/4 VDD is subtracted from the result and compared. Subsequently, the compare voltage is sequentially compared with 1/8 VDD and 1/16 VDD to 1/64 VDD. If the result of comparison is False after comparison has been executed six times, 1/64 VDD is subtracted from the result and comparison is completed.
1 H H H 3/4 H L Compare voltage (xVDD) 1/2 H H L 1/4 H L 0 1/8 L 1/16 3/16 L 25/32 L 49/64 L 3/8 L 5/16 13/16 H 51/64 L 7/16 H 27/32 L 53/64 L H 55/64 5/8 L 9/16 11/16 L 29/32 L 57/64 L L 7/8 L 13/16 15/16 H 59/64 L 15/16 H 31/32 L 61/64 L H 63/64 L 1 63/64 62/64 61/64 60/64 59/64 58/64 57/64 56/64 55/64 54/64 53/64 52/64 51/64 50/64 49/64 48/64
First time
Second time
Third time
Fourth time
Fifth time
Sixth time
Subtracts 1/64 if False
207
PD17016, 17017
(2) Flowchart of binary search method
START Initialization ADCR 100000B ADCCMP = 1? N Resets b5 of ADCR : If result is "0", subtracts 1/2 VDD : Adds 1/4 VDD to result to set compare voltage regardless of whether result is "0" or "1" Y : Detects result of comparison Y : Sets pin to be used
: Sets compare voltage to 1/2 VDD
: Detects result of comparison
Sets b4 of ADCR ADCCMP = 1? N Resets b4 of ADCR
: If result is "0", subtracts 1/4 VDD : Adds 1/8 VDD to result to set compare voltage regardless of whether result is "0" or "1" Y : Detects result of comparison
Sets b3 of ADCR ADCCMP = 1? N Resets b3 of ADCR
: Subtracts 1/8 VDD if result is "0" : Adds 1/16 VDD to result to set compare voltage regardless of whether result is "0" or "1" Y : Detects result of comparison
Sets b2 of ADCR ADCCMP = 1? N Resets b2 of ADCR
: Subtracts 1/16 VDD if result is "0" : Adds 1/32 VDD to result to set compare voltage regardless of whether result is "0" or "1" Y : Detects result of comparison
Sets b1 of ADCR ADCCMP = 1? N Resets b1 of ADCR
: Subtracts 1/32 VDD if result is "0" : Adds 1/64 VDD to result to set compare voltage regardless of whether result is "0" or "1" Y : Detects result of comparison : Subtracts 1/64 VDD if result is "0"
Sets b0 of ADCR ADCCMP = 1? N Resets b0 of ADCR
Detects contents of ADCR END
: Completes conversion with current value if result is "1"
208
PD17016, 17017
(3) Program example of binary search method (a) Method with short conversion time INIT: ADCR7 ADCR6 ADCR5 ADCR4 ADCR3 ADCR2 ADCR1 ADCR0 CLR3 START: INITFLG NOT ADCR3, NOT ADCR2, NOT ADCR1, NOT ADCR0 INITFLG NOT ADCR7, NOT ADCR6, PUT SKT1 CLR1 SET1 PUT SKT1 CLR1 SET1 PUT SKT1 CLR1 SET1 PUT SKT1 CLR1 SET1 PUT SKT1 CLR1 SET1 PUT SKT1 CLR1 END: Number of program steps : 31 steps Number of execution steps: 31 steps A/D conversion time : 137.8 s ADCR, DBF ADCCMP ADCR5 ADCR4 ADCR, DBF ADCCMP ADCR4 ADCR3 ADCR, DBF ADCCMP ADCR3 ADCR2 ADCR, DBF ADCCMP ADCR2 ADCR1 ADCR, DBF ADCCMP ADCR1 ADCR0 ADCR, DBF ADCCMP ADCR0 ; Detects ADCCMP and subtracts ; 1/64 VDD if "0" ; Detects ADCCMP and subtracts ; 2/64 VDD if "0" and adds ; 1/64 VDD ; Detects ADCCMP and subtracts ; 4/64 VDD if "0" and adds ; 2/64 VDD ; Detects ADCCMP and subtracts ; 8/64 VDD if "0" and adds ; 4/64 VDD A/D conversion ; Detects ADCCMP and subtracts ; 16/64 VDD if "0" and adds ; 8/64 VDD ADCR5, NOT ADCR4 ; Sets compare voltage to 31.5/64 VDD ; Detects ADCCMP and subtracts ; 32/64 VDD if "0" and adds ; 16/64 VDD FLG FLG FLG FLG FLG FLG FLG FLG 0.0EH.3 0.0EH.2 0.0EH.1 0.0EH.0 0.0FH.3 0.0FH.2 0.0FH.1 0.0FH.0 ; Dummy ; Dummy ; Defines each bit of data buffer as ADCR data setting flag
ADCCH2, ADCCH1, ADCCH0 ; Sets P1D0/ADC0 pin for the A/D converter
209
PD17016, 17017
(b) Method with fewer program steps ADWORK1 ADWORK0 MEM MEM 0.00H 0.01H ; Work area for changing compare voltage
INITFLG NOT ADCCH2, NOT ADCCH1, NOT ADCCH0 ; Sets P1D0/ADC0 pin for the A/D converter START: MOV MOV MOV MOV AD_CHECK: PUT SKT1 BR ADD ADDC BR ADIN_L: SUB SUBC ; NEXT_AD: RORC RORC SKT1 BR PUT SKT1 AND . . . ADWORK1 ADWORK0 CY AD_CHECK ADCR, DBF ADCCMP DBF0, #1110B ; 6 bits completed? NOP DBF0, ADWORK0 DBF1, ADWORK1 ; Described to keep A/D conversion time constant ; Decreases compare voltage if "0" ADCR, DBF ADCCMP ADIN_L DBF0, ADWORK0 DBF1, ADWORK1 NEXT_AD A/D conversion ; Increases compare voltage if "1" ; Sets compare voltage VREF ; Detects ADCCMP flag DBF1, #0010B DBF0, #0000B ADWORK1, #0001B ADWORK0, #0000B ; Sets compare voltage to initial value of 31.5/64 VDD
Number of program steps : 22 steps Number of execution steps: 58 to 63 steps A/D conversion time : 257.8 to 280 s
Where the A/D conversion time is held constant Number of program steps : 23 steps Number of execution steps: 63 steps A/D conversion time : 280 s
210
PD17016, 17017
16.8 Notes on Using A/D Converter
When the P0D3/ADC5 to P0D0/ADC2 pin is used for the A/D converter and if it is specified that the halt status can be released by key input, the halt status may not be set. This happens because, as explained in 12.4 Halt Function, the pin selected for the A/D converter is disconnected from the latch of the input port. Figure 16-5 shows the relation between the P0D3/ADC5 through P0D0/ADC2 pins and input latch. As shown in this figure, if a high level is input to the input pin when the A/D converter is set by the A/D converter select signal, the status "1" of input latch is retained. Even if an attempt is made to set the state where the halt status is released by key input at this time, therefore, since a high level is being input to this pin, the halt status is immediately released. Figure 16-5. Relation between P0D3/ADC5 through P0D0/ADC2 Pins and Input Latch
P0Dn/ADCm VDD
To A/D converter
Input latch
To port register
A/D converter select signal
16.9 Status on Reset
16.9.1 On power-ON reset All the P0D3/ADC5 through P0D0/ADC2 pins, P1D1/ADC1, and P1D0/ADC0 pins are set in the general-purpose input port mode. 16.9.2 On execution of clock stop instruction All the P0D3/ADC5 through P0D0/ADC2 pins, P1D1/ADC1, and P1D0/ADC0 pins are set in the general-purpose input port mode. 16.9.3 On CE reset All the P0D3/ADC5 through P0D0/ADC2 pins, P1D1/ADC1, and P1D0/ADC0 pins are set in the general-purpose input port mode.
211
PD17016, 17017
17. D/A CONVERTER (DAC)
The D/A converter (DAC) outputs its signal by means of PWM (Pulse Width Modulation) that varies the duty factor. By connecting an external lowpass filter to the D/A converter, digital signals can be converted into analog signals.
17.1 Configuration of D/A Converter
Figure 17-1 shows the block diagram of the D/A converter. As shown in the figure, the D/A converter consists of an output select block and a duty setting block for each pin, and a clock generation block. Figure 17-1. Block Diagram of D/A Converter
Control register
Data buffer
P1B2/PWM1
Output select block
Duty setting block
fPWM1 Clock generation block fPWM0
P1B1/PWM0
Output select block
Duty setting block
17.2 Functional Outline of D/A Converter
The D/A converter outputs a variable-duty signal to each output pin. The output frequency is 878.9 Hz, and the duty factor can be changed in 256 steps. The following subsections 17.2.1 through 17.2.3 outlines the function of each block of the D/A converter. 17.2.1 Output select blocks The output select blocks specify whether each pin is used as a general-purpose output port pin or a D/A converter pin. The mode of each pin is selected by the PWM pin setting software macro supplied with the device file (refer to 17.3). 17.2.2 Duty setting blocks The duty setting blocks output a signal whose duty factor can be changed in 256 steps. The duty factor of each output pin is independently set by the PWM data register (PWMR0 or PWMR1: peripheral address 05H or 06H) via the data buffer. 17.2.3 Clock generation block The clock generation block generates a basic clock that is used to set the duty factor of the output signal. The generated clock frequency fPWM is 225 kHz (refer to 17.4).
212
PD17016, 17017
17.3 Output Select Blocks
17.3.1 Configuration of output select blocks Figure 17-2 shows the configuration of the output select blocks. Figure 17-2. Configuration of Output Select Blocks
PWM pin setting software macro
P1B2/PWM1 1 0 Duty setting block Output latch
P1B1/PWM0 1 0 Duty setting block Output latch
17.3.2 Function of output select blocks The output select blocks select whether the P1B2/PWM1 and P1B1/PWM0 are used as general-purpose output port pins or D/A converter pins. This selection can be made by the PWM pin setting software macro supplied with the device file. Each pin can be set in the port mode or D/A converter mode independently. The P1B2/PWM1 and P1B1/PWM0 pins are N-ch open-drain output pins and must be connected with an external pull-up resistor. Table 17-1 lists the PWM pin setting software macros. Table 17-1. PWM Pin Setting Software Macros
Function Uses P1B1/PWM0 pin as PWM pin Uses P1B2/PWM1 pin as PWM pin Uses P1B1/PWM0 and P1B2/PWM1 pins as PWM pins Uses P1B1/PWM0 pin as general-purpose output port pin Uses P1B2/PWM1 pin as general-purpose output port pin Uses P1B1/PWM0 and P1B2/PWM1 pins general-purpose output port pins Uses P1B1/PWM0 pin as PWM pin and P1B2/PWM1 pin as general-purpose output port pin Uses P1B1/PWM0 pin as general-purpose output port pin and P1B2/PWM1 pin as PWM pin Macro Format SET1_PWM0ON SET1_PWM1ON SET2_PWM1ON_PWM0ON CLR1_PWM0ON CLR1_PWM1ON CLR2_PWM1ON_PWM0ON INIT_NOT_PWM1ON_PWM0ON INIT_PWM1ON_NOT_PWM0ON
Caution
If the above macros are used, the contents of the register window are destroyed. If the above macro instructions immediately follow an embedded macro instruction, an "object error" occurs when the source file is assembled and loaded to the in-circuit emulator. If an embedded macro exists immediately before the above macro instructions, insert a comment statement in between.
213
PD17016, 17017
17.4 Duty Setting Blocks and Clock Generation Block
17.4.1 Configuration of duty setting blocks and clock generation block Figure 17-3 shows he configuration of the duty setting blocks and clock generation block. Figure 17-3. Configuration of Duty Setting Blocks and Clock Generation Block
Data buffer (DBF) Address Symbol Data 0CH DBF3 Don't care 0DH DBF2 Don't care M S B 0EH DBF1 0FH DBF0 L S B
Peripheral address 06H 8 PWM1 data register (PWMR1)
To output block
Comparator fPWM1 225 kHz
Counter (8 bits)
Peripheral address 05H 8 PWM0 data register (PWMR0) Clock generation block
To output block
Comparator fPWM0 225 kHz
Counter (8 bits)
214
PD17016, 17017
17.4.2 Function and configuration of clock generation blocks The clock generation blocks outputs basic clocks (fPWM1 and fPWM0) that set the duty factor of each output signal (of PWM1 and PWM0 pins). The output frequency is 225 kHz (4.44 s) for both fPWM1 and fPWM0. However, fPWM1 and fPWM0 have the following phase difference.
fPWM1 fPWM0 1.11 s 1.11 s 4.44 s
17.4.3 Function and operation of duty setting blocks The duty setting blocks compare the value set to each PWM data register (PWM1 and PWM0) with the value of each basic clock (fPWM1 and fPWM0) counted by an 8-bit counter, and output a high level if the value of the PWM data register is greater, and a low level if the value of PWM data register is less. Where the value set to the PWM data register is "x", the duty factor is as follows. x + 0.25 256
Duty factor: D =
x 100 %
0.25 is an offset. A high level is output even when x = 0. Because the basic clock is 225 kHz, the frequency and cycle of the output signal are as follows. 225 kHz 256 256 225 kHz
Frequency : f =
= 878.9 Hz
Cycle
: t=
= 1137.8 s
An independent value can be set to each PWM data register via the data buffer. In other words, each pin can output a signal with an independent duty factor. The following subsections 17.4.4 and 17.4.5 explain the configuration and function of each PWM data register, and the relation between the output waveform and duty factor of each pin.
215
PD17016, 17017
17.4.4 Configuration and function of each PWM data register The function of each PWM data register is illustrated below. The PWM data register sets the duty factor of a D/A converter (PWM output) output signal.
Name Symbol Address Bit Data b3 DBF3 0CH b2 b1 b0 b3 DBF2 0DH b2 b1
Data buffer DBF1 0EH b0 b3 b2 b1 b0 b3 DBF0 0FH b2 b1 b0
Don't care
Don't care
Transfer data
GET can be executed 8 PUT can be executed Peripheral register Name PWM0 data register Valid data PWM1 data register PWMR1 06H PWM1 pin b7 b6 b5 b4 b3 b2 b1 b0 Symbol PWMR0 Peripheral address 05H Peripheral hardware PWM0 pin
Sets PWM output duty of each pin 0 Duty : D = Frequency : f = x x + 0.25 x 100 % 256 225 kHz 256
= 878.9 Hz
255
216
PD17016, 17017
17.4.5 Relation of output waveform and each pin of D/A converter (1) shows the relation between the output waveform and duty factor. (2) shows the relation of the output waveform of each pin. (1) Duty factor and output waveform
x=0 x=1 x=2 4.44 s 1.11 s 4.44 s
x = 255 3.33 s 1137.8 s
(2) Output waveform of each pin
PWM1 (x = 0) PWM0 (x = 0) 1.11 s 1137.8 s
17.5 Status on Reset
17.5.1 On power-ON reset The P1B2/PWM1 and P1B1/PWM0 pins are set in the general-purpose output port mode. The output value is "undefined". The value of each PWM data register is "undefined". 17.5.2 On execution of clock stop instruction The P1B2/PWM1 and P1B1/PWM0 pins are set in the general-purpose output port mode. The output value is the "previous contents of the output latch". Each PWM data register retains the previous value. 17.5.3 On CE reset The P1B2/PWM1 and P1B1/PWM0 pins retain the previous output status. Therefore, the pin used for the D/A converter retains the current PWM output. 17.5.4 In halt status The P1B2/PWM1 and P1B1/PWM0 pins retain the previous output status. Therefore, the pin used for the D/A converter retains the current PWM output.
217
PD17016, 17017
18. BEEP OUTPUT
The BEEP output function outputs a clock of 200 Hz, 1 kHz, or 3 kHz from the P1B0/BEEP pin.
18.1 Method of BEEP Output
The BEEP output function is controlled by a software macro defined in the device file. To start or stop the BEEP output, describe this software macro in the source program. (1) Software macro starting BEEP output This macro sets the frequency of the BEEP output and the P1B0/BEEP pin in the BEEP output mode, to start the BEEP output. (a) To output 200 Hz BEEPON200 (b) To output 1 kHz BEEPON1K (c) To output 3 kHz BEEPON3K (2) Software macro stopping BEEP output This macro stops the BEEP output. Consequently, the P1B0/BEEP pin can be used as a general-purpose output port pin, and the contents of the output latch at that time can be output. (a) To stop BEEP output BEEPOFF Caution If the above macros are used, the contents of the register window are destroyed. If the above macro instructions immediately follow an embedded macro instruction, an "object error" occurs when the source file is assembled and loaded to the in-circuit emulator. If an embedded macro exists immediately before the above macro instructions, insert a comment statement in between.
218
PD17016, 17017
18.2 Output Waveform of BEEP
The duty factor of the output waveform of BEEP is 50 %. The output waveform is shown below. (1) 200-Hz output
2.5 ms
2.5 ms
(2) 1-kHz output
500 s
500 s
(3) 3-kHz output
116.7 s
116.7 s
18.3 Status on Reset
(1) On power-ON reset The P1B0/BEEP pin is set in the general-purpose output port mode. The value of the output latch is undefined, and therefore undefined data is output. (2) On execution of clock stop instruction The P1B0/BEEP pin is set in the general-purpose output port mode. The value of the output latch before the clock stop instruction is executed is retained, and the value of the output latch at that time is output. (3) On CE reset The P1B0/BEEP pin operates as is with the previous status retained. (4) In halt status The P1B0/BEEP pin operates as is with the previous status retained.
219
PD17016, 17017
18.4 Notes on Using BEEP Function
The BEEP function block shares part of the hardware with the frequency counter that is explained later. Therefore, the BEEP function and frequency counter cannot be used at the same time. If the data of the IF counter mode select register and IF counter data register (IFC: peripheral address 43H) are manipulated while the BEEP function is being used, the operation explained in 18.4.1 is performed. If the BEEP output software macro is executed while the frequency counter is being used, the operation explained in 18.4.2 is performed. 18.4.1 When BEEP function is used (1) When IFCMD1 and IFCMD0 flags of IF counter mode select register are manipulated If a value other than "0" is written to the IFCMD1 and IFCMD0 flags, the P1B0/BEEP pin retains the current output level, and stops the BEEP output. When both the IFCMD1 and IFCMD0 flags are reset to "0", the BEEP output is started. (2) When IF counter data register is manipulated The BEEP output is not affected even if the IF counter data register is read (by GET) or written (by PUT). An "undefined value" is read from the register. Nothing is changed even if data is written to the register. However, do not write anything to the IF counter data register because this register is a read-only register. 18.4.2 When frequency counter is being used If the BEEP output software macro is executed while the frequency counter is being used, the frequency counter is forcibly stopped, and the BEEP output is started. At this time, the contents of the window register (WR) and data buffer (DBF) are destroyed. To operate the frequency counter again, stop the BEEP output once by using the BEEPOFF software macro, and start counting from the beginning.
220
PD17016, 17017
19. SERIAL INTERFACE
The serial interface is used to transfer 8-bit serial data with an external device. Figure 19-1. Block Diagram of Serial Interface
Control register
Data buffer
Peripheral address 03H
P0B2/SCK P0B1/SO P0B0/SI
Presettable shift register I/O control
Clock control Serial interface
Clock generation
221
PD17016, 17017
19.1 Configuration of Serial Interface
Figure 19-2 shows the configuration of the serial interface. As shown in the figure, the shift clock control block of the serial interface consists of a clock I/O pin block, clock generation block, wait control block, and clock count block. The serial data control block consists of a serial data I/O pin block and a presettable shift register. These blocks are controlled by the corresponding flags of the control registers. Data is written to or read from the presettable shift register via the data buffer. The following section 19.2 outlines each block. Figure 19-2. Configuration of Serial Interface
Control register Address Flag symbol S I O 1 T S 02H S I O 1 H I Z S I O 1 C K 1 S I O 1 C K 0
Shift clock I/O pin block WAIT P0B2/SCK P0B2/SCK output control Output latch WRITE port register READ Shift clock output CLKOUT clock control
SF8 Wait control
SF8 Clock counter
P0BBIO2 flag Serial clock input Serial data I/O pin block Address Symbol Data Data buffer (DBF) 0CH 0DH 0EH DBF3 DBF2 DBF1 M S B 03H Serial out data CLKIN DATAOUT DATAIN Presettable shift register 0FH DBF0 L S B
P0B1/SO
P0B1/SO output control
Output latch
WRITE port register READ
P0BBIO1 flag Output latch WRITE port register READ
P0B0/SI
P0BBIO0 flag Serial in data
222
PD17016, 17017
19.2 Functional Outline of Serial Interface
The serial interface uses the P0B2/SCK, P0B1/SO, and P0B0/SI pins. The serial interface can select the internal clock or an external clock, and can execute reception and transfer operations. The following subsections 19.2.1 through 19.2.6 outline the functions of the respective blocks of the serial interface. For details of each block, refer to 19.3 through 19.7. 19.2.1 Shift clock I/O pin block This block selects a shift clock I/O pin. The shift clock I/O pin is selected by the serial I/O mode select register. Refer to 19.3. 19.2.2 Serial data I/O pin block This block selects a serial data I/O pin. The serial data I/O pin is selected by the serial I/O mode select register. Refer to 19.3. 19.2.3 Clock generation block This block selects the clock frequency of the shift clock and controls the shift clock output timing. The shift clock frequency is selected by the serial I/O mode select register. Refer to 19.4. 19.2.4 Clock counter The clock counter counts the number of rising edges of the clock output by the shift clock output pin and outputs a signal at the eighth clock (SF8 signal). The SF8 signal is used to make serial communication wait (pause). Refer to 19.5. 19.2.5 Presettable shift register (SIO1SFR) This shift register sets serial out data and stores serial in data. It performs a shift operation by using the clock of the shift clock I/O pin and inputs/outputs data. The output data is set and the input data is read via the data buffer. Refer to 19.6. 19.2.6 Wait control block This block controls places or releases serial communication in or from the wait status. Serial communication is placed in or released from the wait status by the serial I/O mode select register. Refer to 19.7.
223
PD17016, 17017
19.3 Shift Clock and Serial Data I/O Pin Control Blocks
The shift clock and serial data I/O pin control blocks sets the pins of the serial interface and controls the transfer/reception operation. These control operations are specified by the serial I/O mode select register. 19.3.1 shows the configuration and function of the serial I/O mode select register. 19.3.2 indicates the status of each pin set by the serial I/O mode select register. 19.3.1 Configuration and function of serial I/O mode select register The configuration and function of the serial I/O mode select register are illustrated below. The SIO1CK1 and SIO1CK0 flags are used to select the internal clock or an external clock and to set the frequency of the internal clock. For the details on the clock, refer to 19.4. The SIO1TS flag places or releases the serial interface in or from the wait status. For the wait operation, refer to 19.7.
Name b3 Serial I/O mode select register S I O 1 T S
Flag symbol b2 S I O 1 H I Z b1 S I O 1 C K 1 b0 S I O 1 C K 0
Address
Read/ Write
02H
R/W
Set I/O clock frequency of serial interface 0 0 1 1 0 1 0 1 External clock (slave) 75 kHz (master) 150 kHz (master) 450 kHz (master)
Sets P0B1/SO pin as serial out pin 0 1 General-purpose I/O port Serial out
Starts serial communication of serial interface 0 1 Does not start serial communication (wait) Starts serial communication (wait release)
On reset
Power-ON Clock stop CE
0 0 0
0 0 0
0 0 0
0 0 0
224
PD17016, 17017
19.3.2 Pin status setting by serial I/O mode select register Table 19-1 shows the status of each pin set by the serial I/O mode select register. As shown in this table, the I/O select flag of each pin must be also manipulated to set each pin. For the details on the I/O select flag, refer to 15. GENERAL-PURPOSE PORT. Table 19-1. Pin Status Setting by Serial I/O Mode Select Register
SIO1MODE Communication b2 mode S I O 1 H I Z 3-wire serial I/O 1 Setting of serial output S I O 1 C K 1 0 S I O 1 C K 0 0 External clock P0B2/SCK b1 b0 Clock direction Pin symbol I/O select flag of each pin P 0 B B I O 2 0 P 0 B B I O 1 P 0 B B I O 0 Wait : general-purpose input port Wait released : external clock input Wait : general-purpose output port Wait released : general-purpose output port 0 1 1 0 Generalpurpose port 1 Serial output 1 0 1 1 P0B1/SO 0 1 0 1 P0B0/SI 0 1 Wait : High level output Wait released : General-purpose input port General-purpose input port General-purpose output port General-purpose input port Serial output Serial input General-purpose output port Internal clock 0 Wait : general-purpose input port Wait released : general-purpose input port Pin Set pin status
225
PD17016, 17017
19.4 Clock Generation Block
The clock generation block generates the clock when the internal clock is used (i.e., when the master operation is performed) and controls the clock output timing. The frequency fSC of the internal clock is set by using the SIO1CK1 and SIO1CK0 flags of the serial I/O mode select register. The shift clock is successively output until the value of the clock counter, which is explained in 19.5, reaches "8". The following subsection 19.4.1 explains the clock output waveform and clock generation timing. 19.4.1 Internal shift clock generation timing (1) On releasing wait status from initial status The initial status is the status in which the internal clock is selected, the P0B2/SCK pin is set in the output mode, and a high level is output to this pin. A high level is output to the P0B2/SCK pin in the wait status.
H 450 kHz L 1/2 fsc H 150 kHz L H 75 kHz L Wait status Wait status 1/fsc 1/2 fsc
Initialization
226
PD17016, 17017
(2) When wait operation is performed For the details on the wait operation, refer to 19.7. (a) Wait status with value of clock counter reaching "8" (normal operation)
H Shift clock pin L Wait released status Wait Wait period Wait release 1/fsc
(b) If forced wait is executed in wait status
H L Wait period Wait period
Shift clock pin
Forced wait by SIO1TS
(c) If forced wait is executed when wait status is released At this time, the clock counter is reset.
H Shift clock pin L Wait release status Wait period Wait release 1/fsc
Forced wait by SIO1TS Shift H clock pin L Wait release status Wait period
1/fsc Wait release
Forced wait by SIO1TS
(d) If wait status is released in wait release status The clock output waveform is not changed at this time. The clock counter is not reset. (e) If clock frequency is changed and wait status is released at the same time The clock frequency can be changed and the wait status can be released by the serial I/O mode select register of the control registers. Therefore, the clock frequency can be changed and the wait status can be released with a single instruction. In this case, the operation is the same as releasing the wait status from the initial status as explained in (1).
227
PD17016, 17017
19.5 Clock Counter
The clock counter is a wrap-around counter that counts the number of the shift clocks output from or input to the shift clock (P0B2/SCK) pin. The clock counter directly reads the status of the shift clock pin. At this time, whether the clock is the internal clock or an external clock is not identified. The clock counter does not operate in the wait status of serial communication. When the value of the clock counter is "8", serial communication is placed in the wait status at the rising edge of the shift clock. The contents of the clock counter cannot be directly read by programs. The following subsections 19.5.1 and 19.5.2 explain the operation of the clock counter and the conditions under which the clock counter is reset. 19.5.1 Operation of clock counter Figure 19-3 shows the operation of the clock counter. The initial value of the clock counter is "0". The value of the clock counter is incremented by one each time the falling of the shift clock pin is detected. When the value of the clock counter has been incremented to "8", the clock counter is reset to "0" at the next rising edge of the shift clock pin. Serial communication is placed in the wait status when the clock counter has been reset to "0". Figure 19-3. Operation of Clock Counter
Shift clock pin H 1 L H D7 L D6 D5 D1 D0 2 3 7 8
Serial data pin
Clock counter Resets clock counter
0
1
2
3
7
8
0
Releases wait
Wait
19.5.2 Clock counter reset condition The clock counter is reset to 0 when any of the following conditions (1) through (5) is satisfied. (1) On power-ON reset (2) On execution of the clock stop instruction (3) When "0" is written to the SIO1TS flag (forced wait) (4) When the shift clock rises while the value of the clock counter is "8" with the wait status released (5) On CE reset
228
PD17016, 17017
19.6 Presettable Shift Register (SIO1SFR)
The presettable shift register is an 8-bit shift register that writes serial out data and reads serial in data. Data is written to or read from the presettable shift register via the data buffer by using the "PUT" or "GET" instruction. 19.6.1 shows the configuration of the presettable shift register and its relation with the data buffer. The presettable shift register performs its shift operation in synchronization with the clock applied to the shift clock (P0B2/SCK) pin. At this time, the content of the most significant bit (MSB) of the presettable shift register is output to the serial data output pin in synchronization with the fall of the shift clock, and the least significant bit (LSB) of the presettable shift register is read in synchronization with the rise of the clock. 19.6.2 explains the operation of the presettable shift register. 19.6.3 explains the points to be noted in writing or reading data to or from the presettable shift register. The presettable shift register does not shift data in the wait status. For the details on the operation in each serial communication mode, refer to 19.8. 19.6.1 Configuration of presettable shift register and its relation with data buffer The configuration of the presettable shift register and its relation with the data buffer are shown below.
Name Symbol Address Bit Data b3 DBF3 0CH b2 b1 b0 b3 DBF2 0DH b2 b1
Data buffer DBF1 0EH b0 b3 b2 b1 b0 b3 DBF0 0FH b2 b1 b0
Don't care
Don't care
Transfer data
GET can be executed 8 PUT can be executed Peripheral register Name Presettable shift register b7 M S B Valid data b6 b5 b4 b3 b2 b1 b0 Symbol L S B SIO1SFR Peripheral address 03H Peripheral hardware Serial interface
Sets serial out data and reads serial in data D7 D6 D5 D4 D3 D2 D1 D0 D7D6D5D4D3D2D1D0 Serial out Serial in
229
PD17016, 17017
19.6.2 Operation of presettable shift register Figure 19-4 illustrates the data shift operation of the presettable shift register. Table 19-2 shows the data shift operation during transfer and reception. Figure 19-4. Data Shift Operation of Presettable Shift Register
Shift clock pin H 1 L 2 3 6 7 8
Wait release Clock counter H d7 L H D7 L D6 D5 D2 D1 D0 d6 d5 d2 d1 d0 0 1 2 6 7 8 0
Serial data input pin
Serial data output pin
b7 b6 b5 b4 b3 b2 b1 b0
D7 D6 D5 D4 D3 D2 D1 D0
D6 D5 D4 D3 D2 D1 D0 d7
D5 D4 D3 D2 D1 D0 d7 d6
D1 D0 d7 d6 d5 d4 d3 d2
D0 d7 d6 d5 d4 d3 d2 d1
d7 d6 d5 d4 d3 d2 d1 d0
Presettable shift register
Table 19-2. Data Shift Operation during Transfer and Reception
Serial I/O mode Serial input operation Shifts and inputs status of P0B0/SI pin at rising edge of shift clock starting from LSB. If P0BBIO0 flag is "0", contents of output latch are input. This operation is not performed in wait status. Serial output operation Data is shifted and output, starting from MSB, to P0B1/SO pin at falling edge of shift clock. If P0BBIO1 flag is "1", or if SIO1HIZ flag is "0", data is not output. This operation is not performed in wait status.
230
PD17016, 17017
19.6.3 Notes on setting and reading data Data is written to the presettable shift register by the "PUT SIO1SFR, DBF" instruction. Data is read from the register by the "GET DBF, SIO1SFR" instruction. Set or read data to or from the register in the wait status. While the wait status is released, the data may not be correctly set or read depending on the status of the shift clock pin. Table 19-3 indicates the timing of setting and reading data and points to be noted. Table 19-3. Reading (GET) and Writing (PUT) Data from/to Presettable Shift Register and Notes
Status on Execution of PUT/GET Wait status Read (GET) Status of Shift Clock Pin Presettable Shift Register (SIO1SFR)
With external clock: floated
Normally read.
Write (PUT) With internal clock: high level
Normally written. Content of MSB is output at falling edge of shift clock when wait status is released next time (during transfer operation).
Clock Data PUT SIO1SFR, DBF Wait released MSB
Wait released status
Read (GET)
Low level High level
Normally read. Cannot be read normally. Contents of SIO1SFR are destroyed. Normally written. Contents of MSB are output when PUT instruction is executed. Clock counter is not reset. Clock Data PUT SIO1SFR, DBF MSB
Write (PUT)
High level
Low level
Cannot be written normally. Contents of SIO1SFR are destroyed.
231
PD17016, 17017
19.7 Wait Block
The wait block controls communication of the serial interface by placing or releasing communication in or from the wait status. The wait block is controlled by the SIO1TS flag of the serial I/O mode select register. The following subsection 19.7.1 explains the wait operation and points to be noted. 19.7.1 Wait operation and notes In the wait status, the clock generation block and presettable shift register stop operation, and serial communication pauses. Therefore, serial communication can be started when the wait status is released. The wait status is released when "1" is written to the SIO1TS flag. When "1" is written to this flag, the internal clock is output to the shift clock output pin (during master operation), and presettable shift register and clock counter start operating. If the shift clock rises when the value of the clock counter is "8", the wait status is set. At this time, the SIO1TS flag is automatically reset to "0". The operating status of serial communication can be checked by detecting the content of the SIO1TS flag while the wait status is released. Therefore, data is read or set after "1" has been written to the SIO1TS flag, serial communication has been started, and then clearing of the SIO1TS flag to "0" has been detected. If data is written to (by PUT instruction) or read from (by GET instruction) the presettable shift register while the wait status is released, the correct data may not be written or read. For details, refer to 19.6.3 Notes on setting and reading data. If "0" is written to the SIO1TS flag while the wait status is released, the wait status is set. This is called forced wait. When forced wait is executed, the clock counter is reset to "0". Figure 19-5 shows an example of the wait operation.
232
PD17016, 17017
Figure 19-5. Example of Wait Operation
Shift clock pin H 1 L H d7 L H Previous value L D7 D6 D5 D1 D0 d6 d5 d1 d0 2 3 7 8
Serial data input pin
Serial data output pin Clock counter
0
1
2
3
7
8
0
1 SIO1TS 0 Wait status Wait released status Wait status
Wait released
Wait
When the wait status is released, the serial data is output at the next falling edge of the clock, and the wait status is released. When the shift clock has been input eight times, the shift clock pin outputs a high level, and the clock counter and presettable shift register stop operation. If data is written to or read from the presettable shift register while the wait status is released and the shift clock pin is high, the correct data may not be set or read. If data is written to the presettable shift register while the wait status is released and the shift clock pin is low, the content of the MSB is output to the serial data output pin as soon as the "PUT" instruction has been executed. If forced wait is executed while the wait status is released, the wait status is set and the clock counter is reset to "0" as soon as "0" has been written to the SIO1TS flag.
233
PD17016, 17017
19.8 Using Serial Interface
Figure 19-6 illustrates the I/O block and communication method of the serial interface. Table 19-4 indicates the operations of the serial interface in each mode. As shown in Figure 19-6 and Table 19-4, the serial interface operates on the internal clock (master operation) or external clock (slave operation), and can perform transfer and reception on both the clocks. The master or slave operation is selected by the SIO1CK1 and SIO1CK0 flags. Reception or transfer is selected by the SIO1HIZ flag. During the master operation, the internal shift clock is output from the P0B2/SCK pin. However, the P0B2/ SCK pin must be set in the output port mode (P0BBIO2 flag = 1). During the slave operation, the P0B2/SCK pin is floated, and the serial interface waits for an external clock. At this time, the P0B2/SCK pin must be set in the input port mode (P0BBIO2 flag = 0). Serial data is output from the P0B1/SO pin at the falling edge of the shift clock, regardless of whether the internal clock or external clock is used. However, the P0B1/SO pin must be set in the output port mode (P0BBIO1 flag = 1) and the SIO1HIZ flag must be set. As the serial input data, the status of the P0B1/SO pin is input to the presettable shift register at the rising edge of the shift clock, regardless of whether the internal clock or external clock is used. However, the P0B0/ SI pin must be set in the input port mode (P0BBIO0 flag = 0). The P0B2/SCK pin reads the "current status of the output latch" when the value output to the pin is read, and "the current status of the pin" while the wait status is released. Paragraphs (1) through (4) below Table 19-4 show program examples of transfer and reception during master and slave operations.
234
PD17016, 17017
Figure 19-6. I/O Block and Communication Method of Serial Interface (1/2)
I/O block
P0B2/SCK I/O control block P0BBIO2 SIO1TS SIO1CK1 SIO1CK0
Wait signal
VDD
VDD P-ch P0B2/SCK N-ch 1 0 1 0
Shift clock output P0B2 output latch WRITE port register READ Shift clock input
P0B1/SO I/O control block P0BBIO1 VDD VDD P-ch P0B1/SO N-ch 1 0 1 0 SIO1HIZ
Serial data output P0B1 output latch WRITE port register READ
P0B0/SI I/O control block P0BBIO0 VDD VDD P-ch P0B0/SI N-ch 1 0 P0B0 output latch WRITE port register
READ Serial data input
235
PD17016, 17017
Figure 19-6. I/O Block and Communication Method of Serial Interface (2/2)
Communication
H SI pin L H SO pin L H SCK pin L Data read Data output Hardware control Wait released Wait status 1 2 3 7 8 D7 D6 D1 D0 d7 d6 d1 d0
236
PD17016, 17017
Table 19-4. Operation of Serial Interface in Each Mode
Operation Mode Item 3-Wire Serial I/O Mode Slave operation SIO1CK1 = SIO1CK0 = 0 Wait Setting status of each pin P0B2/SCK When P0BBIO2 = 0 Floating General-purpose input port When P0BBIO2 = 1 General-purpose output port Outputs contents of output. Usually, P0BBIO2 is cleared to 0. When SIO1HIZ = 0 When P0BBIO1 = 0 General-purpose input port Floating When P0BBIO1 = 1 General-purpose output port Outputs contents of output latch. P0B0/SI Wait released When P0BBIO2 = 0 Floating External clock input When P0BBIO2 = 1 General-purpose output port Outputs contents of output latch. Master operation SIO1CK1 = SIO1CK0 = other than 0 Wait When P0BBIO2 = 0 Floating General-purpose input port When P0BBIO2 = 1 Outputs high level. Usually, P0BBIO2 is set to 1. Wait released When P0BBIO2 = 0 Floating General-purpose input port When P0BBIO2 = 1 Outputs internal clock.
P0B1/SO
When SIO1HIZ = 1 When P0BBIO1 = 0 General-purpose input port Floating When P0BBIO1 = 1 Outputs serial data.
When SIO1HIZ = 0 When P0BBIO1 = 0 General-purpose input port Floating When P0BBIO1 = 1 General-purpose output port Outputs contents of output latch.
When SIO1HIZ = 1 When P0BBIO1 = 0 General-purpose input port Floating When P0BBIO1 = 1 Outputs serial data.
When P0BBIO0 = 0 Floating Waits for external data When P0BBIO0 = 1 General-purpose output port. Outputs contents of output latch. Usually, P0BBIO0 is cleared to 0. Incremented at falling edge of SCK pin.
Operation of clock counter Operation of presettable shift register (SIO1SFR)
Output When SIO1HIZ = 1 Shifts data from MSB and outputs it to SO2 pin at falling edge of SCK pin. When SIO1HIZ = 0 Does not output data. Input Shifts data of SI pin from LSB and inputs it at rising edge of SCK pin regardless of P0BBIO0. However, the contents of output latch are output to SI pin when P0BBIO0 = 1. Serial communication is started when "1" is written to SIO1TS. SIO1TS is reset to "0" at rising edge of shift clock when value of clock counter is "8". For operation of each pin, refer to above.
Wait operation
237
PD17016, 17017
(1) Program example of serial interface (in master transfer mode) Example To transfer 2-byte data "A596H" SCKBIO SOBIO MOV MOV PUT SET2 INITFLG FLG FLG P0BBIO2 P0BBIO1
DBF1, #0AH ; Sets transfer data DBF0, #5 SIO1SFR, DBF SCKBIO, S0BIO SIO1TS, SIO1HIZ, NOT SIO1CK1, SIO1CK0 ; Releases wait, and outputs serial data ; Master (fSC = 75 kHz) SIO1TS LOOP1 DBF1, #9 DBF0, #6 SIO1SFR, DBF SIO1TS SIO1TS LOOP2 ; Wait until wait status is released ; Sets transfer data
LOOP1: SKF1 BR MOV MOV PUT SET1 LOOP2: SKF1 BR . . . ; Waits until wait status is released
; Releases wait
(2) Program example of serial interface (in master reception mode) Example To receive 2-byte data and store it to addresses 00H through 03H of BANK0 SCKBIO SIBIO DATA1H DATA1L DATA2H DATA2L FLG FLG MEM MEM MEM MEM P0BBIO2 P0BBIO0 0.00H 0.01H 0.02H 0.03H ; ; ; ; Stores Stores Stores Stores high-order 4 bits of first byte low-order 4 bits of first byte high-order 4 bits of second byte low-order 4 bits of second byte
INITFLG SCKBIO, NOT SIBIO INITFLG SIO1TS, NOT SIO1HIZ, SIO1CK1, SIO1CK0 ; Releases wait, and does not output serial data ; Master (fSC = 450 kHz) LOOP1: SKF1 BR GET ST ST SET1 LOOP2: SKF1 BR GET ST ST . . . SIO1TS LOOP2 DBF, SIO1SFR DATA2H, DBF1 DATA2L, DBF0 ; Waits until wait status is released ; Reads receive data ; Stores read data SIO1TS LOOP1 DBF, SIO1SFR DATA1H, DBF1 DATA1L, DBF0 SIO1TS ; Wait until wait status is released ; Reads receive data ; Stores read data ; Releases wait
238
PD17016, 17017
(3) Program example of serial interface (in slave transfer mode) Example To transfer 2-byte data "A596H" SCKBIO SOBIO INITFLG MOV MOV PUT INITFLG LOOP1: SKF1 BR MOV MOV PUT SET1 LOOP2: SKF1 BR . . . SIO1TS LOOP2 ; Waits until wait status is released SIO1TS LOOP1 DBF1, #9 DBF0, #6 SIO1SFR, DBF SIO1TS ; Wait until wait status is released ; Sets transfer data FLG FLG P0BBIO2 P0BBIO1
NOT SCKBIO, SOBIO DBF1, #0AH ; Sets transfer data DBF0, #5 SIO1SFR, DBF SIO1TS, SIO1HIZ, NOT SIO1CK1, NOT SIO1CK0 ; Releases wait, outputs serial data, slave
; Releases wait
(4) Program example of serial interface (in slave reception mode) Example To receive 2-byte data and store it to addresses 00H through 03H of BANK0 SCKBIO SIBIO DATA1H DATA1L DATA2H DATA2L FLG FLG MEM MEM MEM MEM P0BBIO2 P0BBIO0 0.00H 0.01H 0.02H 0.03H ; ; ; ; Stores Stores Stores Stores high-order 4 bits of first byte low-order 4 bits of first byte high-order 4 bits of second byte low-order 4 bits of second byte
CLR2 SCKBIO, SIBIO INITFLG SIO1TS, NOT SIO1HIZ, NOT SIO1CK1, NOT SIO1CK0 ; Releases wait, does not output serial ; data, slave LOOP1: SKF1 BR GET ST ST SET1 LOOP2: SKF1 BR GET ST ST . . . SIO1TS LOOP2 DBF, SIO1SFR DATA2H, DBF1 DATA2L, DBF0 ; Waits until wait status is released ; Reads receive data ; Stores read data SIO1TS LOOP1 DBF, SIO1SFR DATA1H, DBF1 DATA1L, DBF0 SIO1TS ; Wait until wait status is released ; Reads receive data ; Stores read data ; Releases wait
239
PD17016, 17017
19.9 Status of Serial Interface on Reset
19.9.1 On power-ON reset All of the pins P0B2/SCK through P0B0/SI are set in the general-purpose input port mode (floating output). The value of the presettable shift register is undefined. 19.9.2 On execution of clock stop instruction All of the pins P0B2/SCK through P0B0/SI are set in the general-purpose input port mode (floating output). The presettable shift register retains the previous value. 19.9.3 On CE reset All of the pins P0B2/SCK through P0B0/SI are set in the general-purpose input port mode (floating output). The presettable shift register retains the previous value. 19.9.4 In halt status The I/O pins retain the current status. If the internal clock is used (master operation) at this time, the clock is not output after the "HALT" instruction has been executed. To use the internal clock, therefore, the "HALT" instruction must be executed after communication has been completed. If an external clock is forcibly input, the serial interface functions even when the internal clock is used. If the external clock is used (slave operation), the operation continues even when the "HALT" instruction has been executed.
240
PD17016, 17017
20. FREQUENCY COUNTER (FC)
The frequency counter (FC) is used to count the intermediate frequency (IF) of a tuner.
20.1 Configuration of Frequency Counter
Figure 20-1 shows the block diagram of the frequency counter. As shown in the figure, the IF counter consists of an input select block, gate time control block, start/stop control block, and count block. Figure 20-1. Block Diagram of Frequency Counter
Control register
Data buffer
P1D3/FMIFC P1D2/AMIFC
IF counter input select
Gate time control
Start/stop control
IF counter (16 bits)
20.2 Functional Outline of Frequency Counter
The frequency counter has an IF counter function that is used to count the frequency of an externally input signal. The IF counter function is to count the frequency input to the P1D3/FMIFC or P1D2/AMIFC pin by using a 16bit counter at fixed time intervals (1 ms, 4 ms, 8 ms, or open). The following subsections 20.2.1 through 20.2.4 outline each function block of the frequency counter. Because the frequency counter shares the hardware with the BEEP function explained in 18. BEEP OUTPUT, it cannot be used with the BEEP function at the same time. For details, refer to 20.7 Notes on Using Frequency Counter. 20.2.1 IF counter input select block The IF counter input select block specifies whether the P1D3/FMIFC and P1D2/AMIFC pins are used as general-purpose input port pins or IF counter pins. This selection is made by the IF counter mode select register (RF address 12H). For details, refer to 20.3.
241
PD17016, 17017
20.2.2 Gate time control block The gate time control block controls the time during which the frequency is counted by the IF counter mode select register. The IF counter mode select register sets the internal gate time (1 ms, 4 ms, 8 ms, or open) to count the frequency applied to the P1D3/FMIFC or P1D2/AMIFC pin. For details, refer to 20.3. 20.2.3 Start/stop control block The start/stop control block starts or stops the frequency counter. Starting or stopping the frequency counter is controlled by the IF counter control register (RF address 23H) and IF counter gate judge register (RF address 04H). For details, refer to 20.4. 20.2.4 IF counter The input frequency is counted by a 16-bit binary counter. The count value is read by the IF counter data register (IFC: peripheral address 43H) via the data buffer. For details, refer to 20.4.
242
PD17016, 17017
20.3 Input Select Block and Gate Time Control Block
20.3.1 Configuration of input select block and gate time control block Figure 20-2 shows the configuration of the input select block and gate time control block. Figure 20-2. Configuration of Input Select Block and Gate Time Control Block
Control register Address Bit Flag symbol b3 I F C M D I 12H b2 I F C M D 0 b1 I F C C K 1 b0 I F C C K 0
2-3 decoder F M I F C VDD BEEP Gate time generator (1, 4, 8 ms) Gate time signal
P1D3/FMIFC
1/2
Frequency
Input port
A M I F C
VDD
P1D2/AMIFC
Input port
243
PD17016, 17017
20.3.2 Function of input select block The input select block selects whether the P1D3/FMIFIC and P1D2/AMIFC pins are used as general-purpose output port pins or frequency counter pins. This selection is made by the IFCMD1 and IFCMD0 flags of the IF counter mode select register (refer to 20.3.4). 20.3.3 Function of gate time control block The gate time control block sets a gate time (count time). The gate time is set by the IFCCK1 and IFCCK0 flags of the IF counter mode select register (refer to 20.3.4).
244
PD17016, 17017
20.3.4 Configuration and function of IF count mode select register The IF counter mode select register selects the IF counter function and gate time. The configuration and function of this register are illustrated below. Because the frequency counter is shared with the BEEP function, this register is also used to select the BEEP output.
Name b3 IF counter mode select register I F C M D 1
Flag symbol b2 I F C M D 0 b1 I F C C K 1 b0 I F C C K 0
Address
Read/ Write
12H
R/W
Gate time of IF counter 0 0 1 1 0 1 0 1 1 ms 4 ms 8 ms Open
Selects IF counter or BEEP function 0 0 1 1 0 1 0 1 BEEP output IF counter (FMIFC) IF counter (AMIFC) Setting prohibited
On reset
Power-ON Clock stop CE
0 0
0 0
0 0
0 0
Retained
Caution
The IF counter function and BEEP function cannot be used at the same time.
245
PD17016, 17017
20.4 Start/Stop Control Block and IF Counter
20.4.1 Configuration of start/stop control block and counter Figure 20-3 shows the configuration of the start/stop control block and counter. Figure 20-3. Configuration of Start/Stop Control Block and Counter
Control register Address Bit Flag symbol b3 0 04H b2 b1 0 0 b0 I F C G O S T T Control register Address Bit Flag symbol b3 0 23H b2 b1 I 0 F C S T R T b0 I F C R E S Address Symbol Data Data buffer (DBF) 0CH DBF3 M S B 0DH DBF2 0EH DBF1 0FH DBF0 L S B
16
Peripheral address 43H
IF counter data register (IFC) 16 Gate signal from input select block RES Start/stop IF counter (16 bits)
High-order 6 bits are shared with BEEP function block.
20.4.2 Function of start/stop control block The start/stop control block detects the start and end of counting by the frequency counter. The counting is started by using the IFCSTRT flag of the IF counter control register. To detect the end of the counting, the IFCGOSTT flag of the IF counter gate judge register is used. The following subsections 20.4.6 and 20.4.7 explain the configuration and functions of the IF counter control register and IF counter gate judge register.
246
PD17016, 17017
20.4.3 Gate operation of IF counter (1) When 1, 4, or 8 ms is selected as gate time The gate is opened for 1, 4, or 8 ms since the internal 1-kHz signal has risen after the IFCSTRT flag was set to "1", as shown below. While this gate is open, the frequency input from the pin is counted by the 16-bit counter. When the gate is closed, the IFCGOSTT flag is reset. The IFCGOSTT flag is automatically set to "1" when the IFCSTRT flag has been set.
H L OPEN CLOSE
Internal 1 kHz 1 ms Gate 4 ms time 8 ms
Count period (IFCGOSTT flag = 1) Gate is actually opened at this point. Sets IFCSTRT flag. IFCGOSTT flag is set at this point. End of counting. IFCGOSTT flag is reset.
247
PD17016, 17017
(2) When "open" is selected as gate time As soon as it has been specified by the IFCCK1 and IFCCK0 flags that the gate is "opened", the gate is opened. If counting is started by the IFCSTRT flag while the gate is open, the gate is closed after an undefined time. Therefore, do not set the IFCSTRT flag to "1" when selecting "open" as the gate time. However, the counter can be reset by the IFCRES flag.
Internal 1 kHz Gate H L OPEN CLOSE
Count period If IFCSTRT flag is set during this period, gate is closed after undefined time.
IFCCK1 = IFCCK0 = 1 Gate is actually opened at this point. If gate is opened while IFCGOSTT flag is 1, it is closed after undefined time.
When "open" is selected as the gate time, the gate can be opened or closed in two ways as explained in (a) and (b) below. (a) Set gate time other than "open" by IFCCK1 and IFCCK0 flags
Gate OPEN CLOSE
Count time IFCCK1 = IFCCK0 = 1 Set other than open by IFFCCK1 and IFCCK0 flags.
(b) Unselect pin used by using IFCMD1 and IFCMD0 flags In this case, the gate is remains open, and counting is stopped by inhibiting input from the pin.
Gate OPEN CLOSE
Count time IFCCK1 = IFCCK0 = 1 IFCMD1 = IFCMD0 = 0 (BEEP) FMIFC and AMIFC pins are unselected, and count input is inhibited.
248
PD17016, 17017
20.4.4 Function and operation of 16-bit counter The 16-bit counter counts up the frequency input within the specified gate time. This counter is reset by writing "1" to the IFCRES flag of the IF counter control register. When the 16-bit counter counts up to FFFFH, it is cleared to 0000H and continues counting when the next input is applied. Because the high-order 6 bits of this counter are shared with the BEEP function, the frequency counter and BEEP function cannot be used at the same time. The function of the IF counter is to count the frequency input to the P1D3/FMIFC or P1D2/AMIFC pin while the gate is open. Note, however, that the frequency input to the P1D3/FMIFC pin is divided by two and is counted. The relation between count value "x (HEX)" and input frequency (fFMIFC or fAMIFC) is as follows. FMIFC x (DEC) tGATE
fFMIFC =
x 2 (kHz)
tGATE = gate time (1, 4, or 8 ms)
AMIFC x (DEC) tGATE
fAMIFC =
(kHz)
tGATE = gate time (1, 4, or 8 ms)
The value of the IF counter data register is read via the data buffer. The following subsection 20.4.5 explains the configuration and function of the IF counter data register.
249
PD17016, 17017
20.4.5 Configuration and function of IF counter data register (IFC) The configuration and function of the IF counter data register are illustrated below. The IF counter data register reads the count value of the frequency counter. This register is cleared to 0000H at the next input when its value has reached FFFFH, and continues counting.
Name Symbol Address Bit Data b3 DBF3 0CH b2 b1 b0 b3 DBF2 0DH b2 b1
Data buffer DBF1 0EH b0 b3 b2 b1 b0 b3 DBF0 0FH b2 b1 b0
Transfer data
GET can be executed 16 Peripheral register Name IF counter data register Valid data b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0 Symbol IFC Peripheral address 43H Peripheral hardware Frequency counter Nothing is changed even if PUT is executed.
Count value of frequency counter 0 IF counter function FMIF counter Counts rising edge of signal input to P1D3/FMIFC pin by using 1/2 divider x AMIF counter Counts rising edge of signal input to P1D2/AMIFC pin. 216 - 1 (FFFFH)
The high-order 6 bits of the IF counter are shared with the BEEP function. Therefore, the frequency counter function and BEEP function cannot be used at the same time. For details, refer to 20.7 Notes on Using Frequency Counter.
250
PD17016, 17017
20.4.6 Configuration and function of IF counter control register The IF counter control register starts the frequency counter (IF counter) function and controls resetting of the 16-bit counter. The configuration and function of this register are illustrated below.
Name b3 IF counter control register 0
Flag symbol b2 0 b1 I F C S T R T b0 I F C R E S
Address
Read/ Write
23H
W
Controls count value of IF counter 0 1 Nothing is changed. Resets counter.
Starts counting by IF counter 0 1 Nothing is changed. Starts counting.
Fixed to "0"
On reset
Power-ON Clock stop CE
0
0
0 0
0 0
Retained
The IF counter control register is controlled by writing the contents of the window register by using the "POKE" instruction. When the contents of this register are read to the window register by the "PEEK" instruction, "0" is read. If either of the IFCRES or IFCSTRT flag is set by using the assembler (AS17K) embedded macroinstruction SETn, the flag that is not set becomes "undefined", and an error occurs. For details, refer to 20.7.3 Notes on using embedded macroinstruction SETn to IFCRES and IFCSTRT flags.
251
PD17016, 17017
20.4.7 Configuration and function of IF counter gate judge register The IF counter gate judge register detects the opening and closing of the gate of the IF counter. The configuration and function of this register are illustrated below.
Name b3 IF counter gate judge register 0
Flag symbol b2 0 b1 0 b0 I F C G O S T T
Address
Read/ Write
04H
R
Detects opening/closing of gate of frequency counter Set to 1 until gate time expires after IFCSTRT flag has been set to "1".
Fixed to "0"
On reset
Power-ON Clock stop CE
0
0
0
0
Undefined Undefined
Caution
Do not read the contents of the IF counter data register (IFC) to the data buffer while the IFCGOSTT flag is set to 1 (i.e., while the gate is open).
252
PD17016, 17017
20.5 Using IF Counter Function
The following subsections 20.5.1 through 20.5.3 explain how to use the hardware of the IF counter function, program example, and count error. 20.5.1 Using hardware of IF counter Figure 20-4 shows the block diagram illustrating how the P1D3/FMIFC and P1D2/AMIFC pins are used. Table 20-1 shows the range of the frequencies that can be input to the P1D3/FMIFC and P1D2/AMIFC pins. Because the input pins of the IF counter have an internal amplifier, cut off the DC component of the input signal by using capacitor C as shown in Figure 20-4. When the P1D3/FMIFC or P1D2/AMIFC pin is selected as the IF counter pin, switch SW turns ON, applying a voltage of about 1/2VDD to each pin. If the voltage has not risen to a sufficient intermediate level at this time, the AC amplifier does not operate normally, and consequently, the IF counter does not correctly operate. Therefore, make sure that a sufficiently long wait time elapses from the time each pin is selected as an IF counter until counting is started. Figure 20-4. Function of Each IF Counter Pin
R SW
C External frequency FMIFC AMIFC To internal counter
Table 20-1. Input Frequency Range of IF Counter
Input Pin Input Frequency (MHz) 5-15 10.5-10.9 P1D2/AMIFC 0.1-1 0.44-0.46 Input Amplitude (Vp-p) 0.3 0.06 0.3 0.05
P1D3/FMIFC
253
PD17016, 17017
20.5.2 Program example of IF counter function A program example of the IF counter function is shown below. As shown in this example, wait time must elapse after an instruction that selects the P1D3/FMIFC or P1D2/ AMIFC pin as the IF counter pin has been executed before counting is started. This is because the internal AC amplifier may not operate normally immediately after each pin has been selected, as explained in 20.5.1. Example To count frequency on P1D3/FMIFC pin (gate time: 8 ms) INITFLG NOT Wait IFC_RES_AND_START IFCMD1, IFCMD0, IFCCK1, NOT IFCCK0 ; Selects FMIFC pin and sets gate time to 8 ms. ; Internal AC amplifier stabilization time ; Resets and starts counter (sets IFCRES and ; IFCSTRT flags) Note. ; Macro definition is used because SET2 instruction cannot ; be used. LOOP: SKT1 BR IFCGOSTT READ Processing A BR READ: GET Note DBF, IFC ; Reads value of IF counter data register to data buffer. LOOP ; Detects opening/closing of gate. ; Branches to READ: when gate is closed. ; Do not read data of IF counter by this processing A. ; Do not select BEEP function.
Refer to 20.7.3 Notes on using embedded macroinstruction SETn to IFCRES and IFCSTRT flags.
20.5.3 Error of IF counter The IF counter may have a gate time error and a count error. These errors are explained in (1) and (2) below. (1) Error of gate time The gate time of the IF counter is created by dividing the 4.5-MHz system clock. Therefore, if the system clock deviates "+x" ppm, the gate time deviates "-x" ppm. (2) Count error The IF counter counts the frequency at the rising edge of an input signal. If a high level is input to the pin when the gate is opened, therefore, one excess pulse is counted. However, counting is not performed because of the status of the pin when the gate is closed. Therefore, a count error of "+1, -0" may occur.
254
PD17016, 17017
20.6 Status on Reset
20.6.1 On power-ON reset The P1D3/FMIFC and P1D2/AMIFC pins are set in the general-purpose input port mode. 20.6.2 On execution of clock stop instruction The P1D3/FMIFC and P1D2/AMIFC pins are set in the general-purpose input port mode. 20.6.3 On CE reset The P1D3/FMIFC and P1D2/AMIFC pins retain the previous status. 20.6.4 In halt status The P1D3/FMIFC and P1D2/AMIFC pins retain the status immediately before the halt status is set. To release the halt status by using the interrupt of the frequency counter, the following point must be noted. Caution If the "HALT" instruction is executed after counting has been started by the IFCSTRT flag and before the gate is actually opened, the gate will not be opened. Therefore, wait at least 1 ms after starting counting before executing the "HALT" instruction. Figure 20-5 shows the gate operation when the "HALT" instruction is executed. Because the closing of the gate cannot be detected unless the gate is opened, the interrupt request is not issued. If interrupts other than that of the IF counter are not enabled with halt release conditions other than the interrupt not specified, the HALT status will not be released. Figure 20-5. Gate Operation When "HALT" Instruction Is Used
OPEN Gate CLOSE
Gate is actually opened at this point. Interrupt request is not issued because gate is not opened if HALT instruction is executed during this period. Sets IFCSTRT flag.
255
PD17016, 17017
20.7 Notes on Using Frequency Counter
The frequency counter shares its hardware with the BEEP function explained earlier. Therefore, the BEEP function and frequency counter cannot be used at the same time. If the data of the IF counter mode select register and IF counter data register are manipulated while the BEEP function is used, the operation explained in 20.7.1 is performed. If the BEEP output software macro is executed when the frequency counter is used, the operation explained in 20.7.2 is performed. The assembler embedded macroinstruction SETn cannot be used to manipulate the IFCRES and IFCSTRT flags, as explained in 20.4.6. This is explained in more detail in 20.7.3. 20.7.1 When BEEP output is used (1) When IFCMD1 and IFCMD0 flags of IF counter mode select register are manipulated If a value other than "0" is written to the IFCMD1 and IFCMD0 flags, the P1B0/BEEP pin retain the current output level, and stops the BEEP output. When both the IFCMD1 and IFCMD0 flags are reset to "0" again, the BEEP output is started. (2) When IF counter data register is manipulated The BEEP output is not affected even if a read (GET) or write (PUT) instruction is executed. When the IF counter data register is read, an "undefined" value is read. Nothing is changed even if data is written to the register. Note, however, that the IF counter data register is a read-only peripheral register. Do not write data to this register. If the write instruction "PUT IFC, DBF" is executed, the 17 series assembler outputs an error. 20.7.2 When frequency counter is used If the BEEP output software macro is executed while the frequency counter is used, the frequency counter is forcibly stopped, and the BEEP output is started. At this time, the contents of the window register (WR) and data buffer (DBF) are destroyed. To operate the frequency counter again, once stop the BEEP output by using the BEEPOFF macro, and start counting from the beginning.
256
PD17016, 17017
20.7.3 Notes on using embedded macroinstruction SETn to IFCRES and IFCSTRT flags Because the IFCRES and IFCSTRT flags are in a write-only register, an "undefined" value is read if these flags are read. If either of these flags is set by assembler (AS17K) embedded macroinstruction "SETn", an "undefined" value is written to the other flag. SET1 IFCRES PEEK OR POKE WR,.MF.IFCRES SHR4 WR,#.DF.IFCRES AND 0FH .MF.IFCRES SHR 4, WR ; Value of WR is "undefined" at this time. ; Only bit 0 of WR is set. ; Undefined value is written to IFCSTRT (bit 1).
If the SETn instruction is executed to the IFCRES and IFCSTRT flag, therefore, the assembler outputs an error. Therefore, use macro definition to manipulate the IFCRES and IFCSTRT flags as follows. IFCW ; IFC_RES_AND_START MOV POKE ENDM ; IFC_RES MOV POKE ENDM ; IFC_START MOV POKE ENDM The above macroinstruction is supplied with the device file as "IFCSET.LIB" file and "D17016.INC/D17017.INC" file. Therefore, the above macroinstruction can be used as is by INCLUDEing these files on the source program. For how to use each file, refer to AS17016 Device File User's Manual. WR, IFCW, WR MACR0 #0010B WR, IFCW, WR MACR0 #0001B WR, IFCW, WR MACR0 #0011B MEM 0.0A3H
257
PD17016, 17017
21. LCD CONTROLLER/DRIVER
The LCD (Liquid Crystal Display) controller/driver can display an LCD of up to 60 dots by outputting segment and common signals in combination.
21.1 Configuration of LCD Controller/Driver
Figure 21-1 shows the block diagram of the LCD controller/driver. As shown in the figure, the LCD controller/driver consists of a common signal output timing control block, segment signal/key source signal output timing control block, segment signal/output port select block, LCD segment register, and key source signal output control block. The following section 21.2 outlines the function of each block. Figure 21-1. Block Diagram of LCD Controller/Driver
Data buffer
Control register
LCD segment register data memory space
Key source signal output control
Segment signal/key source signal output timing control
Common signal output timing control
Segment signal/ output port select
C O M
1
C O M
0
L Selection by software C D macro 29 / P 0 F
3
L C D
26
L C D
25
L C D
22
L C D
21
L C D
16
L C D
15
L C D
0
/ P 0 F
0
/ P 0 E
3
/ P 0 E
0
/ K S
15
/ K S
0
258
PD17016, 17017
21.2 Functional Outline of LCD Controller/Driver
The LCD controller/driver can display up to 60 dots by using the combination of common signal output pins (COM1 and COM0) and segment signal output pins (LCD29/P0F3 through LCD0/KS0). Figure 21-2 shows the relation among common signal output pins, segment signal output pins, and display dots. As shown in this figure, two dots at the intersections between one segment line with COM1 and COM0 pins. The driving mode is 1/2 duty, 1/2 bias, and the drive voltage is supply voltage VDD. The segment signal output pins (LCD29/P0F3 through LCD22/P0E0) pins can also be used as general-purpose output port pins. When these pins are used as general-purpose output port pins, ports 0F (LCD29/P0F3 through LCD26/P0F0) and 0E (LCD25/P0E3 through LCD22/P0E0) can be independently used. Of the segment signal output pins, the LCD15/KS15 through LCD0/KS0 pins are also used as key source signal output pins. The key source signals and LCD segment signals are output by means of time-division multiplexing. For the details on the general-purpose output ports, refer to 15. GENERAL-PURPOSE PORT. For the details on the key source signals, refer to 22. KEY SOURCE CONTROLLER/DECODER. The following subsections 21.2.1 through 21.2.5 outlines the function of each block of the LCD controller/ driver. Figure 21-2. Common Signal Output, Segment Signal Output, and Display Dot
COM1 pin Display dot COM0 pin Segment signal output pin (LCDn)
21.2.1 LCD segment register The LCD segment register sets dot data that is used to turn ON/OFF the LCD. Because this register is mapped on the data memory, it can be controlled by any data memory manipulation instruction. When the segment signal output pins are used as general-purpose output port pins, this registers sets output data. For details, refer to 21.3.
259
PD17016, 17017
21.2.2 Common signal output timing control block The common signal output timing control block controls the common signal output timing of the COM1 and COM0 pins. These pins output a low level when the LCD is not displayed. Whether the LCD is displayed or not is selected by the LCD mode select register (RF address 10H). For details, refer to 21.4. 21.2.3 Segment signal/key source signal output timing control block The segment signal/key source signal output timing control block controls the segment signal output timing of the LCD29/P0F3 through LCD0/KS0 pins. These pins output a low level when the LCD is not displayed. Whether the LCD is displayed or not is selected by the LCD mode select register. The segment signal/key source signal output timing control block controls the timing of the segment and key source signals output from the LCD15/KS15 through LCD0/KS0 pins. Whether the key source signals are used or not is selected by the LCD mode select register. For details, refer to 21.4. 21.2.4 Segment signal/general-purpose port select block The segment signal/general-purpose port select block selects whether each segment signal output pin is used for LCD display (to output a segment signal) or as a general-purpose output port pin. This selection is made by using the software macro supplied with the device file. For details, refer to 21.4. 21.2.5 Key source signal output control block The key source signal output control block sets the key source output data that are output from the LCD15/ KS15 through LCD0/KS0 pins and detects key input timing. The key source signal output data are set by the key source data register (KSR: peripheral address 42H) via the data buffer. To use the key source signals, the P0D3/ADC5 through P0D0/ADC2 pins are used as key input pins. For details, refer to 22. KEY SOURCE CONTROLLER/DECODER.
260
PD17016, 17017
21.3 LCD Segment Register
The LCD segment register specifies whether each dot on the LCD is turned ON/OFF. 21.3.1 Configuration of LCD segment register Figure 21-3 shows the location of the LCD segment register on the data memory. Figure 21-4 shows the configuration of the LCD segment register. Figure 21-3. Location of LCD Segment Register on Data Memory
Column address 0 0 1
Row address
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
DBF
2 Data memory 3 4 5 6 7 7 7 7 System register 0 1 2 3 4 5 6 7 8 9 A B C D E F BANK0 LCD segment register BANK1 BANK2 BANK3
Note
Note
BANK3 is not provided on the PD17016. Figure 21-4. Configuration of LCD Segment Register
LCD segment register 66H 67H 68H
Address
60H
61H
62H
63H
64H
65H
69H
6AH
6BH
6CH
6DH
6EH
6FH -
Symbol LCDD0 LCDD1 LCDD2 LCDD3 LCDD4 LCDD5 LCDD6 LCDD7 LCDD8 LCDD9 LCDD10 LCDD11 LCDD12 LCDD13 LCDD14
Nothing is allocated to this address. This address cannot be used as a data memory area. LCDD0 b3 b2 b1 b0
261
PD17016, 17017
21.3.2 Function of LCD segment register Figure 21-5 shows the relation of 1 nibble (4 bits) of the LCD segment register and LCD display dots. As shown in this figure, 1 nibble of the LCD segment register can set display data (ON/OFF data) of 4 dots. The LCD display dot corresponding to a bit that is set to "1" is turned ON, and the dot corresponding to a bit that is reset to "0" is turned OFF. The LCD segment register also sets output data when the segment signal output pins are used as output port pins. Figure 21-6 shows the relation between each LCD segment register and LCD display dots that are turned ON/OFF. Figure 21-5. Relation of 1 Nibble of LCD Segment Register and LCD Display Dots
LCD segment register Address Bit m b3 b2 b1 b0
COM1 pin COM0 pin
b3 b2
b1 b0
LCDn-1 pin LCDn pin
262
PD17016, 17017
[MEMO]
263
PD17016, 17017
Figure 21-6. Relation among LCD Display Dots, Ports 0E and 0F, Key Source Output, and Each Data Setting Register (1/2)
Key source data register Key (peripheral address) source Bit Generalpurpose port Port register (RAM address) Bit P0F (6DH) b3 b2 b1 b0 P0E (6BH) b3 b2 b1 b0
P 0 F
3
P 0 F
2
P 0 F
1
P 0 F
0
P 0 E
3
P 0 E
2
P 0 E
1
P 0 E
0
COM1 pin (43)
b3
b1
b3
b1
b3
b1
b3
b1
b3
b1
b3
b1
b3
b1
COM0 pin (44)
b2
b0
b2
b0
b2
b0
b2
b0
b2
b0
b2
b0
b2
b0
L C D
29
L C D
28
L C D
27
L C D
26
L C D
25
L C D
24
L C D
23
L C D
22
L C D
21
L C D
20
L C D
19
L C D
18
L C D
17
L C D
16
Pin No. LCD segment register (RAM address) Bit
(45)
(46)
(47)
(48)
(49)
(50)
(51)
(52)
(53)
(54)
(55)
(56)
(57)
(58)
b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 LCDD14 (6EH) LCDD13 (6DH) LCDD12 (6CH) LCDD11 (6BH) LCDD10 (6AH) LCDD9 (69H) LCDD8 (68H)
LCD function
264
PD17016, 17017
Figure 21-6. Relation among LCD Display Dots, Ports 0E and 0F, Key Source Output, and Each Data Setting Register (2/2)
KSR (42H) b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0
15
K S
14
K S
13
K S
12
K S
11
K S
10
K S
K S
9
K S
8
K S
7
K S
6
K S
5
K S
4
K S
3
K S
2
K S
1
K S
0
b3
b1
b3
b1
b3
b1
b3
b1
b3
b1
b3
b1
b3
b1
b3
b1
Correspondence of segment register bit
b2
b0
b2
b0
b2
b0
b2
b0
b2
b0
b2
b0
b2
b0
b2
b0
L C D
15
L C D
14
L C D
13
L C D
12
L C D
11
L C D
10
L C D
9
L C D
8
L C D
7
L C D
6
L C D
5
L C D
4
L C D
3
L C D
2
L C D
1
L C D
0
(59)
(60)
(61)
(62)
(63)
(64)
(65)
(66)
(67)
(68)
(69)
(70)
(71)
(72)
(73)
(74)
b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 b3 b2 b1 b0 LCDD7 (67H) LCDD6 (66H) LCDD5 (65H) LCDD4 (64H) LCDD3 (63H) LCDD2 (62H) LCDD1 (61H) LCDD0 (60H)
265
PD17016, 17017
21.4 Output Timing Control Blocks and Segment/Port Select Block
21.4.1 Configuration of output timing control blocks and segment/port select block Figure 21-7 shows the configuration of the common signal and segment signal/key source signal output timing control block and segment signal/general-purpose output port select block. Figure 21-7. Configuration of Timing Control Blocks and Port Select Block
Control register Address Bit Flag symbol b3 0 10H b2 0 b1 K S E N b0 L C D E N
VDD LCD0/KS0 Segment signal/ key source signal timing control
Key source data register b0 LCD segment b1 register
LCD15/KS15 VDD LCD16 Segment signal timing control b0 LCD segment b1 register
LCD21 LCD22/P0E0 LCD25/P0E3 LCD26/P0F0 VDD LCD28/P0F2 1 0 Segment signal timing control VDD LCD29/P0F3 1 0 Segment signal timing control Port data b2 LCD segment b3 register
b0 LCD segment b1 register
Setting by software macro VDD VDD COM0
Basic clock for timing control
Common signal timing control
COM1
266
PD17016, 17017
21.4.2 Function of segment signal/general-purpose output port select block The segment signal/general-purpose output port select block specifies whether each pin is used as a segment signal output pin or a general-purpose output port pin, by using the software macro supplied with the device file (refer to Table 21-1. Software Macros Setting Ports (P0E and P0F)). For the details on the general-purpose output port, refer to 15. GENERAL-PURPOSE PORT. Table 21-1. Software Macros Setting Ports (P0E and P0F)
Function Uses LCD22/P0E0-LCD25/P0E3 pins as general-purpose output port Uses LCD26/P0F0-LCD29/P0F3 pins as general-purpose output port Uses LCD22/P0E0-LCD25/P0E3 pins and LCD26/P0F0-LCD29/P0F3 pins as general-purpose output port Uses LCD22/P0E0-LCD25/P0E3 pins as LCD segment signal output pins Uses LCD26/P0F0-LCD29/P0F3 pins as LCD segment signal output pins Uses LCD22/P0E0-LCD25/P0E3 and LCD26/P0F0-LCD29/P0F3 pins as LCD segment signal output pins Uses LCD22/P0E0-LCD25/P0E3 pins as LCD segment signal output pins and LCD26/P0F0LCD29/P0F3 pins as general-purpose output port Uses LCD22/P0E0-LCD25/P0E3 pins as general-purpose output port and LCD26/P0F0-LCD29/ P0F3 pins as LCD segment signal output pins Macro Format SET1_P0EON SET1_P0FON SET2_P0EON_P0FON
CLR1_P0EON CLR1_P0FON CLR2_P0EON_P0FON
INIT_NOT_P0EON_P0FON
INIT_P0EON_NOT_P0FON
Caution
If the above macros are used, the contents of the window register are destroyed. If the above macros are immediately follow an embedded macro instruction, an "object error" occurs when the source file is assembled and loaded to the in-circuit emulator. If an embedded macro is used before the above macros, insert a comment statement in between them.
21.4.3 Functions of output timing control blocks The output timing control blocks control the timing of the common and segment signals for LCD display and the timing of the key source and segment signals when the key source controller/decoder is used. The common and segment signals are output when the LCDEN flag of the LCD mode select register is "1". In other words, all the LCD display dots can be turned OFF by the LCDEN flag. When all the LCD display dots have been turned OFF, the common and segment signals output a low level. The key source signals are output when the KSEN flag of the LCD mode select register is "1". Therefore, use of the key source signal can be specified by the KSEN flag. 21.4.4 explains the configuration and function of the LCD mode select register. 21.4.5 shows the output waveforms of the common and segment signals. For the details on the key source controller/decoder, refer to 22. KEY SOURCE CONTROLLER/DECODER.
267
PD17016, 17017
21.4.4 Configuration and function of LCD mode select register The LCD mode select register turns ON/OFF all the LCD display dots, and specifies output of the key source signals. The configuration and function of this register are illustrated below.
Name b3 LCD mode select register 0
Flag symbol b2 0 b1 K S E N b0 L C D E N
Address
Read/ Write
10H
R/W
Turns ON/OFF all LCD display dots 0 1 Display OFF (all segment and common signals are low) Display ON
Sets output of key source signal 0 1 Key source OFF Key source ON
Fixed to "0"
On reset
Power-ON Clock stop CE
0
0
0 0
0 0
Retained
268
PD17016, 17017
21.4.5 Output Waveforms of Common and Segment Signals Figures 21-8 and 21-9 show the output waveforms of the common and segment signals. Figure 21-8 shows the output waveform with the key source signals not output, and Figure 21-9 shows the output waveform with the key source signals output. As shown in Figure 21-8, the LCD driver outputs signals with a frame frequency of 125 Hz at 1/2 duty, 1/2 bias (voltage average mode). As the common signals, three levels of voltages (0, 1/2 VDD, and VDD) each having a phase difference of 1/4 from the others are output from the COM1 and COM0 pins. Therefore, voltages in a range of 1/2VDD 1/2 VDD are output. This display mode is called 1/2 bias drive mode. As the segment signals, two levels (0, VDD) of voltages each having a phase corresponding to a display dot are output from each segment signal output pin. Because two display dots (A and B) are turned ON/OFF by one segment pin as shown in Figure 21-8, four types of phases <1> through <4> shown in Figure 21-8 are output by combination of dots A and B, and ON and OFF. Dots A and B are turned ON when the potential difference between the common and segment signals reaches VDD. The duty factor at which each of dots A and B is turned ON is 1/2, and the frequency of the LCD clock is 250 Hz. This display mode is called 1/2 duty drive mode, and the frame frequency is 125 Hz.
269
PD17016, 17017
Figure 21-8. Output Waveforms of Common and Segment Signals (with key source signals not output)
Dot A Dot B Each segment signal output pin (LCDn)
COM1 pin COM0 pin
Common signals
COM1 pin VDD 1/2VDD GND COM0 pin VDD 1/2VDD GND Frame frequency 125 Hz
Each segment pin
<1> A = OFF, B = OFF
<2> A = ON, B = OFF A = ON <3> A = OFF, B = ON B = ON <4> A = ON, B = ON A = ON B = ON A = ON B = ON A = ON B = ON B = ON B = ON A = ON A = ON
2 ms
2 ms
2 ms
2 ms
2 ms
2 ms
270
PD17016, 17017
Figure 21-9. Output Waveforms of Common and Segment Signals (with key source signals output)
Dot A Dot B Each segment signal output pin (LCDn)
COM1 pin COM0 pin
Common signals
COM1 pin VDD 1/2VDD GND COM0 pin VDD 1/2VDD GND
Each segment pin (pin outputting "1" as key source)
<1> A = OFF, B = OFF
<2> A = ON, B = OFF A = ON <3> A = OFF, B = ON B = ON <4> A = ON, B = ON A = ON B = ON A = ON B = ON A = ON B = ON B = ON B = ON A = ON A = ON
Each segment pin (pin outputting "0" as key source)
<1> A = OFF, B = OFF
<2> A = ON, B = OFF A = ON <3> A = OFF, B = ON B = ON <4> A = ON, B = ON A = ON 2 ms B = ON 2 ms A = ON 2 ms B = ON 2 ms A = ON 2 ms B = ON 2 ms B = ON B = ON A = ON A = ON
271
PD17016, 17017
21.5 Using LCD Controller/Driver
Figure 21-10 shows an example of wiring an LCD panel. An example of a program that turns ON a 7-segment LCD panel by using the LCD0 through LCD3 pins as shown in Figure 21-10 is shown below. Example PMN0 CH LCDDATA: ; ; DW DW DW DW DW DW DW DW DW DW DW DW DW DW DW DW
MEM FLG
0.01H DBF0.1
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
; Preset memory number and BK data storage area ; Symbol definition of least significant bit of DBF as "CH" display flag ; Display table data b3 b2 b1 b0 b3 b2 b1 b0 ; Corresponds to LCD segment register fbegdca- ; Corresponds to LCD group register 00000000B ; BLANK 01000100B ;1 01111010B ;2 01011110B ;3 11010100B ;4 10011110B ;5 10111110B ;6 11000110B ;7 11111110B ;8 11011110B ;9 11111010B ;A 11111110B ;B 10101010B ;C 11101110B ;D 10111010B ;E 10110010B ;F
CLR2_P0EON_P0FON ; Software macro MOV RPL, #1110B MOV AR3, #.DL.LCDDATA SHR 12 MOV AR2, #.DL.LCDDATA SHR 8 MOV AR1, #.DL.LCDDATA SHR 4 MOV AR0, #.DL.LCDDATA ADD AR0, PMN0 ADDC AR1, #0 ADDC AR2, #0 ADDC AR3, #0 MOVT DBF, @AR MOV RPH, #0000B MOV RPL, #0000B SKGE PMN0, #0AH SET1 CH LD LCDD1, DBF1 LD LCDD0, DBF0 SET1 LCDEN
AND AND AND AND
0FH 0FH 0FH 0FH
272
Figure 21-10. Example of Wiring of LCD Panel
A FM MW SW LW 1 e 1d 1 f 1g 1 c 2 e 1a 1 b 2 f
B 2a 2 b 2g 2 c 2d 3 e 3 f
C 3a 3 b 3g 3 c 3d 4 e 4 f
D 4a 4 b 4g 4 c 4d E F G AM PM MHz kHz 5 e 5d 5 f 5g 5 c CH 5a 5 b
CCL OOC MMD
1 0 29
L C D
28
L C D
27
L C D
26
LL CC DD
25 24
L C D
23
L LLL L C CCC C D DDD D
22 212019 18
L C D
17
L C D
16
LL CC DD
15 14
L C D
13
L C D
12
LL CC DD
11 10
L C D
9
LL CC DD
87
LL CC DD
65
LLL CCC DDD
432
L C D
1
L C D
0
Correspondence between segment and common pins on LCD panel
Segment Pin L C D
29
L C D
28
L C D
27
L C D
26
L C D
25
L C D
24
L C D
23
L C D
22
L C D
21
L C D
20
L C D
19
L C D
18
L C D
17
L C D
16
L C D
15
L C D
14
L C D
13
L C D
12
L C D
11
L C D
10
L C D
9
L C D
8
L C D
7
L C D
6
L C D
5
L C D
4
L C D
3
L C D
2
L C D
1
L C D
0
Common Pin COM1
45
46
47
48
49 1f
50 1e
51 1d
52 1a
53
54 A
55 2f
56 2e
57 2d
58 2a
59 3f
60 3e
61 3d
62 3a
63 4f
64 4e
65 4d
66 4a
67 F
68 E
69
70
71
72 5e
73 5d
74
PD17016, 17017
43 FM MW
PM AM 5f
5a
COM0
44 SW LW
1b
1g
1c
B
2b
2g
2c
:
3b
3g
3c
C
4b
4g
4c
D
G kHz MHz 5b
5g
5c CH
273
PD17016, 17017
21.6 Status on Reset
21.6.1 On power-ON reset The LCD29/P0F3 through LCD0/KS0 pins are specified as LCD segment signal output pins, and output a low level. The COM1 and COM0 pins output a low level. Therefore, the LCD display is turned OFF. 21.6.2 On execution of clock stop instruction The LCD29/P0F3 through LCD0/KS0 pins are specified as LCD segment signal output pins, and output a low level. The COM1 and COM0 pins output a low level. Therefore, the LCD display is turned OFF. 21.6.3 On CE reset Of the LCD29/P0F3 through LCD0/KS0 pins, those that are specified as segment signal output pins output segment signals, and those that are specified as general-purpose output port pins retain the current output value. The COM1 and COM0 pins output common signals. 21.6.4 In halt status Of the LCD29/P0F3 through LCD0/KS0 pins, those that are specified as segment signal output pins output segment signals, and those that are specified as general-purpose output port pins retain the current output value. The COM1 and COM0 pins output common signals.
274
PD17016, 17017
22. KEY SOURCE CONTROLLER/DECODER
The key source controller/decoder can configure a key matrix of up to 64 keys by outputting key source signals from the pins that also output LCD segment signals. Whether key source signals or LCD segment signals are output from the pins is controlled by means of time-division multiplexing.
22.1 Configuration of Key Source Controller/Decoder
Figure 22-1 shows the configuration of the key source controller/decoder. As shown in the figure, the key source controller/decoder consists of a segment signal/key source signal timing control block, key source data register, key input control block, and P0D port register. The following section 22.2 outlines the function of each block. Figure 22-1. Block Diagram of Key Source Controller/Decoder
Control register
Data buffer
Key source data register (KSR) 16 LCD display data Key source data latch P0D port register (data memory)
Segment signal/key source signal output timing control
Key input control
L C D
15
L C D
14
L C D
2
L C D
1
L C D
0
P O D
3
P O D
2
P O D
1
P O D
0
/ K S
15
/ K S
14
/ K S
2
/ K S
1
/ K S
0
/ A D C
5
/ A D C
4
/ A D C
3
/ A D C
2
Key matrix
275
PD17016, 17017
22.2 Functional Outline of Key Source Controller/Decoder
The key source controller/decoder can configure a key matrix of up to 64 keys by using key source signal output pins (LCD15/KS15 through LCD0/KS0) and key input pins (P0D3/ADC5 through P0D0/ADC2). Figure 22-2 shows the example of key matrix configuration. The LCD15/KS15 through LCD0/KS0 pins are multiplexed with LCD segment signal output pins. Therefore, the key source signals and LCD segment signals are output by means of time-division multiplexing. The following subsections 21.2.1 through 22.2.3 outline the function of each block of the key source controller/ decoder. Figure 22-2. Example of Key Matrix Configuration
Key source output pin
Key source input pin
22.2.1 Key source data register (KSR) The key source data register sets the key source output data of the pin that outputs a key source signal. Data are set to the key source data register via the data buffer. When data are set to this register, the key source data are output from the LCD15/KS15 through LCD0/KS0 pins. For details, refer to 22.3. 22.2.2 Segment signal/key source signal output timing control block The segment signal/key source signal output timing block controls the output timing of the key source and segment signals of the LCD29/P0F3 through LCD0/KS0 pins. Whether a key source signal is used or not is specified by the LCD mode select register. The key source signal is not output when LCD display is not used. In this case, the above pins output a low level. Whether LCD display is not used or not is specified by the LCD mode select register. For details, refer to 22.4.
276
PD17016, 17017
22.2.3 Key input control block and P0D port register The key input control block detects the key input signals input to the P0D3/ADC5 through P0D0/ADC2 pins in synchronization with key source signal output timing. To output the key source signals from the LCD15/KS15 through LCD0/KS0 pins, therefore, the P0D3/ADC5 through P0D0/ADC2 pins are used as key input pins. The key input data are read by the P0D port register (address 73H of BANK0) on the data memory. Because the P0D3/ADC5 through P0D0/ADC2 pins are multiplexed with the A/D converter pins, care must be exercised when using these pins as the A/D converter pins. For details, refer to 22.5.
22.3 Key Source Data Setting Block
22.3.1 Configuration of key source data setting block Figure 22-3 shows the configuration of the key source data setting block. Figure 22-3. Configuration of Key Source Data Setting Block
Data buffer (DBF) Address Symbol Data 0CH DBF3 M S B 16 0DH DBF2 0EH DBF1 0FH DBF0 L S B Peripheral address 42H
Key source data register (KSR)
Key source data latch
22.3.2 Function of key source data setting block The key source data setting block sets the key source data to be output from the LCD15/KS15 through LCD0/ KS0 pins. The key source data are set to the key source data register (KSR: peripheral address 42H) via the data buffer. Each bit of the key source data register corresponds to the LCD15/KS15 through LCD0/KS0 pins, and sets the key source data of each pin. When "1" is set to a bit of the key source data register, the pin corresponding to this bit outputs a high level as a key source signal; when the bit is reset to "0", the corresponding pin outputs a low level. For the output timing, refer to 22.4. The following subsections 22.3.3 explains the configuration and function of the key source data register. Also refer to Figure 21-6 in 21. LCD CONTROLLER/DRIVER.
277
PD17016, 17017
22.3.3 Configuration and function of key source data register (KSR) The configuration and function of the key source data register are illustrated below.
Name Symbol Address Bit Data b3 DBF3 0CH b2 b1 b0 b3 DBF2 0DH b2 b1
Data buffer DBF1 0EH b0 b3 b2 b1 b0 b3 DBF0 0FH b2 b1 b0
Transfer data
GET can be executed 16 PUT can be executed Peripheral register Name Key source Valid data data register b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0 Symbol KSR Peripheral address 42H Peripheral hardware Key source controller/decoder
Selects output pin of key source signal LCD0/KS0 pin LCD1/KS1 pin LCD2/KS2 pin LCD3/KS3 pin LCD4/KS4 pin LCD5/KS5 pin LCD6/KS6 pin LCD7/KS7 pin LCD8/KS8 pin LCD9/KS9 pin LCD10/KS10 pin LCD11/KS11 pin LCD12/KS12 pin LCD13/KS13 pin LCD14/KS14 pin LCD15/KS15 pin 0 1 Does not output key source signal Outputs key source signal
278
PD17016, 17017
22.4 Output Timing Control Blocks and Segment/Port Select Block
22.4.1 Configuration of output timing control blocks and segment/port select block Figure 22-4 shows the configuration of the common signal and segment signal/key source signal output timing control blocks and segment signal/general-purpose output port select block. Figure 22-4. Configuration of Timing Control Blocks and Port Select Block
Control register Address Bit Flag symbol b3 0 10H b2 0 b1 K S E N b0 L C D E N
VDD LCD0/KS0 Segment signal/ key source signal timing control
key source data register b0 LCD segment b1 register
LCD15/KS15
Basic clock for timing control
279
PD17016, 17017
22.4.2 Function of output timing control blocks The output timing control blocks controls the output timing of the key source and segment signals. The LCD segment signal is output when the LCDEN flag of the LCD mode select register is "1". All the LCD display dots can be turned OFF by resetting the LCDEN flag to "0". At this time, a low level is output as the segment signal, and the key source signal is not output. To output the key source signal, therefore, the LCDEN flag must be "1". The key source signal is also output when the KSEN flag of the LCD mode select register is "1". Therefore, the KSEN flag is used to specify whether the key source signal is used or not. To output the key source signal, therefore, the LCDEN and KSEN flags must be "1". The following subsection 22.4.3 indicate the configuration and function of the LCD mode select register. Subsection 22.4.4 shows the output waveforms of the key source and segment signals. For the relation among the common and segment signals of the LCD, and key source signal, refer to 21. LCD CONTROLLER/DRIVER.
280
PD17016, 17017
22.4.3 Configuration and function of LCD mode select register The LCD mode select register turns ON/OFF all the LCD display dots, and specifies output of the key source signal. The configuration and function of this register are illustrated below.
Name b3 LCD mode select register 0
Flag symbol b2 0 b1 K S E N b0 L C D E N
Address
Read/ Write
10H
R/W
Turns ON/OFF all LCD display dots 0 1 Display OFF (all segment and common output pins output low level) Display ON
Selects output of key source signal 0 1 Key source OFF Key source ON
Fixed to "0"
On reset
Power-ON Clock stop CE
0
0
0 0
0 0
Retained
22.4.4 Output waveforms of segment and key source signals Figure 22-5 shows the output waveforms of the key source and segment signals. As shown in the figure, the key source and segment signals are output by means of time-division multiplexing. The key source signal is output for 220 s at intervals of 4 ms. To put it in another way, a pin corresponding to a bit of the key source data register that is set to "1" outputs a high level for 220 s every 4 ms, and a pin corresponding to a bit of the key source data register that is reset to "0" outputs a low level for 220 s every 4 ms. When output of the key source signal is selected (KSEN flag = 1), pins that do not output key source signals (LCD29/P0F3 through LCD16) output the waveform shown in Figure 22-5. However, a waveform of "0" is output as the key source data.
281
PD17016, 17017
Figure 22-5. Output Waveforms of Key Source and Segment Signals
COM1 pin COM0 pin Dot A Dot B Segment signal Key source signal
Each segment/key source signal output pin (LCDn/KSn)
Connon signals
COM1 pin VDD 1/2VDD GND COM0 pin VDD 1/2VDD GND
Each segment pin (pin outputting "1" as key source)
<1> A = OFF, B = OFF
<2> A = ON, B = OFF A = ON <3> A = OFF, B = ON B = ON <4> A = ON, B = ON A = ON B = ON A = ON B = ON A = ON B = ON B = ON B = ON A = ON A = ON
Each segment pin (pin outputting "0" as key source)
<1> A = OFF, B = OFF
<2> A = ON, B = OFF A = ON <3> A = OFF, B = ON B = ON <4> A = ON, B = ON A = ON Key source signal 220 s 2 ms 2 ms 2 ms 2 ms 2 ms 2 ms B = ON A = ON B = ON A = ON B = ON B = ON B = ON A = ON A = ON
282
PD17016, 17017
22.5 Key Input Control Block
22.5.1 Configuration of key input control block Figure 22-6 shows the configuration of the key input control block. Figure 22-6. Configuration of Key Input Control Block
Control register Address 16H Bit b3 b2 b1 b0 Flag 000K E symbol Y J Segment signal/key source signal output timing control
VDD A/D converter P0D3/ADC5 1 0 Input latch
Write instruction Port register (1 bit) Read instruction
KEYJ FF
Read & Reset
Key source timing signal High ON resistance ADC channel select signal P0D2/ADC4 P0D1/ADC3 P0D0/ADC2
Halt release signal
22.5.2 Function of key input control block The key input control block controls the timing to read the key input signals from the P0D3/ADC5 through P0D0/ ADC2 pins and reads the key input data. Figure 22-7 illustrates the key input signals and key input timing. As shown in this figure, the internal-pull down resistors of the P0D3/ADC5 through P0D0/ADC2 pins are turned OFF while the display data of the LCD segment is output, and turned ON only for 220 s while the key source signal is output. For the duration of 220 s during which the key source signal is output, the input signal of each key input pin is connected to the input latch. Therefore, the signal input to each key input pin can be detected in the 220 s during which the key source signal is output. Figure 22-8 shows the timing chart of the key source signal, key input signal, and key input data (P0D port register). Whether a key source signal is output or not is detected by the KEYJ flag of the key input judge register (RF address 16H). The KEYJ flag is set after the key source signal has been output for 220 s, and is reset when data has been set to the key source data register and when the content of the KEYJ flag has been read. By detecting the KEYJ flag after the key source signal data has been output to the key source data register, and then detecting the status of each key input pin after the KEYJ flag has been set to "1", the key can be input. The following subsection 22.5.3 explains the configuration and function of the key input judge register.
283
PD17016, 17017
Figure 22-7. Key Source Signal and Key Input Timing
COM1 pin COM0 pin Dot A Dot B Segment signal Key source signal
Each segment/key source signal output pin (LCDn/KSn)
Each segment pin (pin outputting "1" as key source, A = ON, B = OFF)
H Segment pin L Pull down Key input pin Open 1 KEYJ flag 0 Key source signal 220 s 2 ms 2 ms
PUT KSR, DBF or SKT 1 KEYJ
PUT KSR, DBF or SKT1 KEYJ Signal input to P0D3/ADC5 through P0D0/ADC2 pins is connected to input latch during this period. If PUT KSR, DBF is executed during this period, KEYJ flag is not set for 4 ms. Input data is latched at this point.
Figure 22-8. Timing Chart of Key Source Signal, Key Input Signal, and Key Input Data (P0D port register)
H Segment pin L <1> When P0D port register is "1" H Key input pin input signal L 1 P0D port register 0 <2> When P0D port register is "0" H Key input pin input signal L 1 P0D port register 0 KEYJ flag is "0" during this period. If value of P0D is read, status of P0D pin is read. Input data is latched at this point.
284
PD17016, 17017
22.5.3 Configuration and function of key input judge register The key input judge register detects the presence or absence of the key input signal latch when the LCD segment signal output pins are shared with key source signal output. The configuration and functions of this register are illustrated below.
Name b3 Key input judge register 0
Flag symbol b2 0 b1 0 b0 K E Y J
Address
Read/ Write
16H
R & Reset
Detects presence/absence of latch of key input signal 0 1 No key latch Key latch
Fixed to "0"
On reset
Power-ON Clock stop CE
0
0
0
0
Undefined Undefined
The key source data is set by setting the contents of the data buffer to the key source data register by using the "PUT" instruction. When the key source signal output data is set by the "PUT" instruction via the data buffer, the KEYJ flag is reset to "0". The KEYJ flag is also reset to "0" (Read & Reset) when the contents of the window register are read by the "PEEK" instruction.
285
PD17016, 17017
22.6 Using Key Source Controller/Decoder
22.6.1 Configuring key matrix Figure 22-9 shows an example of configuring a key matrix. As shown in this figure, the key matrix can be configured for up to 64 keys. Because the key source signal output pins also output the LCD segment signals at the same time, diode "A" must be used to prevent reverse flow of the LCD segment signal if a momentary switch is used. Diodes "B" and "C" are used to prevent sneaking of the key source signal. Use a PNP transistor as the transistor switch. The following (1) explains the points to be noted when an NPN transistor is used. (2) through (4) explain the points to be noted if diodes A, B, and C are not used. Figure 22-9. Example of Key Matrix Configuration
A
B
To LCD panel
78
77
76
75
74
73
72
71
70
69
68
67
66
65
60
59
Configuration of each switch
Momentary switch KS K
Alternate switch KS K
Diode switch KS K
C KS K K Or C KS K KS K KS
286
PD17016, 17017
(1) Notes on using NPN transistor switch When an NPN transistor switch is used, the low level may not be accurately read as illustrated in the figure below. -------------------------------If KS is low and a high level is input to the base of the transistor in the figure on the left, voltage VK input to K is as follows. RB RA + RB
VDD High RA Low K Internal resistor RB KS
VK =
x (VDD - VBE)
A low level must be input to K at this time because KS is low. However, the voltage input to K changes depending on RA and RB, as indicated by the above expression. Therefore, a low level may not be input depending on the values of RA and RB.
(2) Notes when diode A is not used An example of a circuit where diode A is missing is shown below. Suppose switches SW1 and SW2 are ON, KS15 outputs a high level, and KS14 outputs a low level, as shown below. If diode A is missing, currents I1 and I2 indicated by the dotted lines flow. Consequently, the high level of KS15 and low level of KS14 are not output correctly because of I2, and the key input data of K3 cannot be accurately read. If KS15 and KS14 are used to output LCD segment signals, the LCD cannot be turned ON/OFF correctly.
SW1
LCD SW2
LCD I1 I2 Low High
K2
K3
KS14
KS15
287
PD17016, 17017
(3) Notes when diode B is not used An example of a circuit where diode B is not used is shown below. Suppose switches SW1, SW2, and SW4 are ON, and KS7 outputs a high level, as shown below. If diode B is missing, currents I1 and I2 flow as indicated by the dotted lines. Consequently, a high level is input to K2 because of I2 despite that switch SW3 is OFF, and it is judged that SW3 is ON.
SW1
SW2
SW3
SW4
I2
I1
High
Low
K2
K3
KS7
KS8
(4) Note when diode C is not used An example of a circuit where diode C is not used is shown below. Suppose switches SW2, SW3, and SW4 are ON, and KS8 outputs a high level, as shown below. If diode C is missing, currents I1, I2, and I3 flow as indicated by the dotted lines. Consequently, a high level is input to K2 because of I2 despite the fact that switch SW1 is OFF, and it is judged that SW1 is ON. Moreover, KS8 cannot output a high level correctly because of I3.
SW1
SW2
SW3
SW4
I2
I1
I3
Low
High
K2
K3
KS7
KS8
288
PD17016, 17017
22.6.2 Reading alternate switches and diode switches Here is a program example. Example To read statuses of alternate and diode switches of LCD15/KS15 through LCD8/KS8 pins to addresses 20H through 27H of BANK0 of data memory KS8 KEY_IN KEY_LOAD: SET2 MOV MOV MOV MOV MOV MOV MOV MOV KSCAN: PUT LOOP: SKF1 BR KEYJ KCHECK ; Determines if key input is latched KSR, DBF ; Outputs signal of key source data LCDEN, KSEN DBF3, #0000B DBF2, #0001B DBF1, #0000B DBF0, #0000B IXM, #0000B IXL, #0000B RPH, #0000B RPL, #0000B ; LCD segment and key source signal output ; Sets key source data ; Outputs low level from KS8 NIBBLE8 0.20H MEM 0.73H
; P0D port register
Processing A BR KCHECK: MOV SET1 ST CLR1 MOV INC ADD ADD SKT1 BR KEY_END: LOOP
; Waits until key input is latched
RPL#.DM.KEY_IN SHR 3 AND 0EH IXE KS8, KEY_IN ; Stores key input data to data memory IXE RPL, #0000B IX DBF2, DBF2 ; Updates value of key source data and DBF3, DBF3 ; scans key again CY ; Determines if all key source lines are input KSCAN ; End of input
289
PD17016, 17017
22.6.3 Inputting momentary switch by binary search The key source controller/decoder requires 4 ms to input the key of one key source signal line. To input the keys of 16 key source signals, therefore, it takes 64 ms. It is therefore convenient if the binary search method explained in (1) and (2) below is used. (1) Flowchart When KS7 through KS0 are used as key source signals of momentary switch
START Initialization RA 0000B ; Sets key source controller ; Sets offset address of table storing key source data to RA
AR KSDATA+RA @AR DBF KSR DBF KEYJ = 1? Y RB P0D port register RA = RB = 0? N Y RA > 7? N RA RA+RA N Y N
; Outputs key source data at offset address specified by RA
; Waits until data is latched to key input latch (4 ms) ; Saves key input data to RB ; If key input data and RA are "0", inputs all keys again because no ; key is input ; If RA is greater than "7", input of one key source ends and waits for ; chattering ; If RA is less than "7", updates RA and continues binary search
RB = 0? Y RA RA+1
RB = 0? N Chattering wait DBF KSR KSR DBF
Y
; If there is no key input data, checks all keys again
; Even if this chattering wait is missing, chattering occurs for 4 ms ; Inputs key input determined by binary search to RC again N
KEYJ = 1? Y RC P0D port register RC = 0? N Checking of key data
Y
; If RC = 0, occurrence of chattering is determined, and keys are input ; from beginning
; Stores key input data before chattering to RB, data after chattering ; to RC, and key source data to RA
END
290
PD17016, 17017
Example of table data for binary search
Shift Address (RA) 0000B 0001B 0010B 0011B 0100B 0101B 0110B 0111B 1000B 1001B 1010B 1011B 1100B 1101B 1110B 1111B Table Data (Key Source Data) b15 b14 b13 b12 b11 b10 b9 b8 b7 b6 b5 b4 b3 b2 b1 b0
(2) Program example RA RB RC MEM MEM MEM 0.1AH 0.1BH 0.1CH 0.73H ; General-purpose work register ; General-purpose work register ; General-purpose work register ; P0D port register
KEY_IN MEM KSDATA: ; ; ; ; DW DW DW DW DW DW DW DW DW DW DW DW DW DW DW DW KEY_LOAD: SET2 START: MOV
KKKKKKKKKKKKKKKK SSSSSSSSSSSSSSSS 1111119876543210 543210 0000000011111111B 0000000011110000B 0000000000001100B 0000000000110000B 0000000000000010B 0000000000001000B 0000000000100000B 0000000010000000B 0000000000000001B 0000000000000010B 0000000000000100B 0000000000001000B 0000000000010000B 0000000000100000B 0000000001000000B 0000000010000000B LCDEN, KSEN RA, #0000B
; ; ; ; ; ; ; ; ; ; ; ; ; ; ; ;
RA RA RA RA RA RA RA RA RA RA RA RA RA RA RA RA
= = = = = = = = = = = = = = = =
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
; LCD segment and key source signal output
291
PD17016, 17017
KSCAN: MOV MOV MOV MOV MOV ADD ADDC ADDC ADDC MOV MOVT PUT LOOP1: SKF1 BR KEYJ KCHECK ; Determines if key input is latched AR3, AR2, AR1, AR0, RPL, AR0, AR1, AR2, AR3, RPL, DBF, #.DL.KSDATA SHR 0CH AND 0FH #.DL.KSDATA SHR 8 AND 0FH #.DL.KSDATA SHR 4 AND 0FH #.DL.KSDATA AND 0FH #.DL.AR0 SHR 3 AND 0EH RA #0 #0 #0 #0 @AR ; Reads table data ; Outputs signal of key source data
KSR, DBF
Processing A BR KCHECK: MOV LD SKNE SKE BR BR Key input: SKLT BR ADD SKE ADD BR LASTCHK: MOV SKNE BR LOOP1
; Waits until key input is latched
PRL, #.DM.RB SHR 3 AND 0EH RB, KEY_IN ; Stores key input data to RB RA, #0000B ; All keys are checked? RB, #0000B Key input START ; There is no key input RA, RA LASTCHK RA, RA RB, #0000B RA, #0001B KSCAN RPL, #0 RB, #0000B START ; Key sources are narrowed down to one? ; If not, updates value of RA, and scans keys again
; Key input to one key source? ; If not, it is determined that chattering occurs
Chattering wait
292
PD17016, 17017
LOOP2: SKF1 BR KEYJ KEYDEC ; Determines if key input is latched
Processing B BR KEYDEC: MOV LD SET2 SUB SKT1 BR KEY_END: LOOP2
; Waits until key input is latched
RPL, #.DM.RC SHR 3 AND 0EH RC, KEY_IN ; Stores key input data to latch CAP, Z ; Compares key input data after chattering with key input RC, RB ; data before chattering wait Z START ; If data differ ; Stores key source data to RA, key input data before ; chattering to RB, and key input data after chattering to RC
293
PD17016, 17017
22.7 Status on Reset
22.7.1 On power-ON reset The LCD29/P0F3 through LCD0/KS0 pins are specified as the LCD segment signal output pins and output a low level (display OFF). A low level is output as the key source signal. 22.7.2 On execution of clock stop instruction The LCD29/P0F3 through LCD0/KS0 pins are specified as the LCD segment signal output pins and output a low level (display OFF). A low level is output as the key source signal. 22.7.3 On CE reset The output data is retained as is if the key source signal is being output. 22.7.4 In halt status The output data is retained as is if the key source signal is being output. If key input is specified as a halt status releasing condition, the halt status is released when a high level is input to the P0D3/ADC5 through P0D0/ADC2 pins. If the key source controller is used, however, the halt status is released only by a high level that is input within 220 s during which the key source data is output. To release the halt status by key input by using the key source controller, do not use the P0D3/ADC5 through P0D0/ADC2 pins for the A/D converter. For an explanation of how to release the halt status by key input, refer to 12.4 Halt Function.
294
PD17016, 17017
23. INSTRUCTION SET 23.1 Outline of Instruction Set
b14-b11 BIN 0000 0001 0010 0011 0100 0101 0110 0111 b15 HEX 0 1 2 3 4 5 6 7 ADD SUB ADDC SUBC AND XOR OR INC INC RORC MOVT PUSH POP GET PUT PEEK POKE BR CALL RET RETSK RETI EI DI STOP HALT NOP 1000 1001 1010 1011 1100 1101 1110 1111 8 9 A B C D E F LD SKE MOV SKNE BR BR BR BR r, m r, m r, m r, m r, m r, m r, m AR IX r DBF, @AR AR AR DBF, p p, DBF WR, rf rf, WR @AR @AR ADD SUB ADDC SUBC AND XOR OR m, #n4 m, #n4 m, #n4 m, #n4 m, #n4 m, #n4 m, #n4 0 1
s h
r, m m, #n4 @r, m m, #n4 addr (page 0) addr (page 1) addr (page 2) addr (page 3)
ST SKGE MOV SKLT CALL MOV SKT SKF
m, r m, #n4 m, @r m, #n4 addr (page 0) m, #n4 m, #n m, #n
295
PD17016, 17017
23.2 Legend
AR ASR addr BANK CMP CY DBF h INTEF INTR INTSK IX MP MPE m mR mC n n4 PAGE PC p pH pL r rf rfR nfC SP s WR (x) : address register : address stack register indicated by stack pointer : program memory address (low-order 11 bits) : bank register : compare flag : carry flag : data buffer : halt release condition : interrupt enable flag : register automatically saved to stack when interrupt occurs : interrupt stack register : index register : data memory row address pointer : memory pointer enable flag : data memory address indicated by mR, mC : data memory row address (high-order) : data memory column address (low-order) : bit position (4 bits) : immediate data (4 bits) : page (bit 11 of program counter: PD17016) (bits 11 and 12 of program counter: PD17017) : program counter : peripheral address : peripheral address (high-order 3 bits) : peripheral address (low-order 4 bits) : general register column address : register file address : register file address (high-order 3 bits) : register file address (low-order 4 bits) : stack pointer : stop release condition : window register : contents addressed by x
296
PD17016, 17017
23.3 Instruction Set List
Instructions Mnemonic Operand Operation Instruction Code op Code Add ADD r, m m, #n4 ADDC r, m m, #n4 INC AR IX Subtract SUB r, m m, #n4 SUBC r, m m, #n4 Logical operation AND OR r, m m, #n4 r, m m, #n4 XOR r, m m, #n4 Judge SKT SKF Compare SKE SKNE SKGE SKLT Rotate RORC m, #n m, #n m, #n4 m, #n4 m, #n4 m, #n4 r (r) (r) + (m) (m) (m) + n4 (r) (r) + (m) + CY (m) (m) + n4 + CY AR AR + 1 IX IX + 1 (r) (r) - (m) (m) (m) - n4 (r) (r) - (m) - CY (m) (m) - n4 - CY (r) (r) (m) (m) (r) (r) (m) (m) (r) (r) (m) (m) (m) n4 (m) n4 (m) n4 n = n, then skip n = 0, then skip 00000 10000 00010 10010 00111 00111 00001 10001 00011 10011 00110 10110 00100 10100 00101 10101 11110 11111 01001 01011 11001 11011 (r)
b1
Operand mR mR mR mR 000 000 mR mR mR mR mR mR mR mR mR mR mR mR mR mR mR mR 000 mC mC mC mC 1001 1000 mC mC mC mC mC mC mC mC mC mC mC mC mC mC mC mC 0111 r n4 r n4 0000 0000 r n4 r n4 r n4 r n4 r n4 n n n4 n4 n4 n4 r
CMP 0, if (m) CMP 0, if (m)
(m) - n4, skip if zero (m) - n4, skip if not zero (m) - n4, skip if not borrow (m) - n4, skip if borrow CY (r) (r) (m) (m) (r) if MPE = 1: (MP, (r)) (m) if MPE = 0: (BANK, mR, (r)) (m) if MPE = 1: (m) (MP, (r)) if MPE = 0: (m) (BANK, mR, (r)) (m) n4 SP SP - 1, ASR PC, PC AR, DBF (PC), PC ASR, SP SP + 1 SP SP - 1, ASR AR AR ASR, SP SP + 1 WR (rf)
b3
(r)
b2
(r)
b0
00111
Transfer
LD ST MOV
r, m m, r @r, m
01000 11000 01010
mR mR mR
mC mC mC
r r r
m, @r
11010
mR
mC
r
m, #n4 MOVT DBF, @AR
11101 00111
mR 000
mC 0001
n4 0000
PUSH POP PEEK
AR AR WR, rf
00111 00111 00111
000 000 rfR
1101 1100 0011
0000 0000 rfC
Caution
The program memory addresses that can be specified by the address register range as follows:
PD17016: 0000H through 00FFH PD17017: 0000H through 1EFBH
297
PD17016, 17017
Instructions Mnemonic Operand Operation Instruction Code op Code Transfer POKE GET PUT Branch BR rf, WR DBF, p p, DBF addr @AR Subroutine CALL addr (rf) WR DBF (p) (p) DBF Note PC AR SP SP - 1, ASR PC PC11 0, PC10 - 0 addr SP SP - 1, ASR PC PC AR PC ASR, SP SP + 1 PC ASR, SP SP + 1 and skip PC ASR, INTR INTSK, SP SP + 1 INTEF 1 INTEF 0 s h STOP HALT No operation 00111 00111 00111 Note 00111 11100 000 rfR pH pH Operand 0010 1011 1010 addr 0100 addr 0000 rfC pL pL
@AR
00111
000
0101
000
RET RETSK RETI Interrupt EI DI Others STOP HALT NOP
00111 00111 00111 00111 00111 00111 00111 00111
000 001 010 000 001 010 011 100
1110 1110 1110 1111 1111 1111 1111 1111
0000 0000 0000 0000 0000 s h 0000
Note
The operation and op code of "BR addr" of the PD17016 and PD17017 are as follows. (a) PD17016
Mnemonic BR Operand addr Operation PC10 - 0 addr, PAGE 0 PC10 - 0 addr, PAGE 1 op Code 01100 01101
(b) PD17017
Mnemonic BR Operand addr Operation PC10 - 0 addr, PAGE 0 PC10 - 0 addr, PAGE 1 PC10 - 0 addr, PAGE 2 PC10 - 0 addr, PAGE 3 op Code 01100 01101 01110 01111
Caution
The program memory addresses that can be specified by the address register range as follows:
PD17016: 0000H through 00FFH PD17017: 0000H through 1EFBH
298
PD17016, 17017
23.4 Assembler (AS17K) Embedded Macroinstruction
Legend flag n : FLG symbol n <> : bit number : can be omitted
Mnemonic Embedded macro SKTn SKFn SETn CLRn NOTn Operand flag 1, ... flag n flag 1, ... flag n flag 1, ... flag n flag 1, ... flag n flag 1, ... flag n Operation if (flag 1) to (flag n) = all "1", then skip if (flag 1) to (flag n) = all "0", then skip (flag 1) to (flag n) 1 (flag 1) to (flag n) 0 if (flag n) = "0", then (flag n) 1 if (flag n) = "1", then (flag n) 0 if description = NOT flag n, then (flag n) 0 if description = flag n, then (flag n) 1 (BANK) n n 1n4 1n4 1n4 1n4 1n4 1n4 Note
INITFLG
flag 1, ... < flag n>
BANKn
Note
0 n 2: PD17016 0 n 3: PD17017
299
PD17016, 17017
23.5 Software Macroinstructions
23.5.1 BEEP output software macro
Item Controls BEEP output Macro format BEEPON200 BEEPON1K BEEPON3K BEEPOFF Outputs 200 Hz Outputs 1 kHz Outputs 3 kHz Stops BEEP output Function
Caution
If the above macros are used, the contents of the window register are destroyed. If an embedded macro instruction is used immediately before the above macro instructions, an "object error" occurs when the source file is assembled and then loaded to the in-circuit emulator. To use an embedded macro instruction immediately before the above macro instructions, insert a comment statement between them.
23.5.2 Flag manipulation software macro
Item Detects INT0 pin status Macro format SKT1_INT0 SKF1_INT0 Sets interrupt enable flag SET1_IPTM SET1_IP0 SET2_IPTM_IP0 CLR1_IPTM CLR1_IP0 CLR2_IPTM_IP0 INIT_NOT_IPTM_IP0 INIT_IPTM_NOT_IP0 Resets interrupt request flag CLR1_IRQTMNote CLR1_IRQ0Note Function Skips next instruction if high level is input to INT0 pin Skips next instruction if low level is input to INT0 pin Enables timer interrupt Enables INT0 pin interrupt Enables timer interrupt and INT0 pin interrupt Disables timer interrupt Disables INT0 pin interrupt Disables timer interrupt and INT0 pin interrupt Disables timer interrupt and enables INT0 pin interrupt Enables timer interrupt and disables INT0 pin interrupt Resets timer interrupt request Resets INT0 pin interrupt request
Note
While any of these macros is executed, any other interrupt request cannot be acknowledged. For details, refer to 10.11 Notes on Using Interrupt.
Caution
If the above macros are used, the contents of the window register are destroyed. If an embedded macro instruction is used immediately before the above macro instructions, an "object error" occurs when the source file is assembled and then loaded to the in-circuit emulator. To use an embedded macro instruction immediately before the above macro instructions, insert a comment statement between them.
300
PD17016, 17017
Item Sets general-purpose output port/LCD segment signal output (P0E, P0F) Macro format SET1_P0EON Function Uses LCD22/P0E0-LCD25/P0E3 pins as general-purpose output port Uses LCD26/P0F0-LCD29/P0F3 pins as general-purpose output port Uses LCD22/P0E0-LCD25/P0E3 pins and LCD26/P0F0-LCD29/ P0F3 pins as general-purpose output port Uses LCD22/P0E0-LCD25/P0E3 pins as LCD segment signal output pins Uses LCD26/P0F0-LCD29/P0F3 pins as LCD segment signal output pins Uses LCD22/P0E0-LCD25/P0E3 and LCD26/P0F0-LCD29/P0F3 pins as LCD segment signal output pins Uses LCD22/P0E0-LCD25/P0E3 pins as LCD segment signal output pins and LCD26/P0F0-LCD29/P0F3 pins as generalpurpose output port Uses LCD22/P0E0-LCD25/P0E3 pins as general-purpose output port and LCD26/P0F0-LCD29/P0F3 pins as LCD segment signal output pins Uses P1B1/PWM0 pin as PWM pin Uses P1B2/PWM1 pin as PWM pin Uses P1B1/PWM0 and P1B2/PWM1 pins as PWM pins Uses P1B1/PWM0 pin as general-purpose output port pin Uses P1B2/PWM1 pin as general-purpose output port pin Uses P1B1/PWM0 and P1B2/PWM1 pins as general-purpose output port pins Uses P1B1/PWM0 pin as PWM pin and P1B2/PWM1 pin as general-purpose output port pin Uses P1B1/PWM0 pin as general-purpose output port pin and P1B2/PWM1 pin as PWM pin
SET1_P0FON
SET2_P0EON_P0FON
CLR1_P0EON
CLR1_P0FON
CLR2_P0EON_P0FON
INIT_NOT_P0EON_P0FON
INIT_P0EON_NOT_P0FON
Sets general-purpose output port/PWM pin signal (P1B1, P1B2)
SET1_PWM0ON SET1_PWM1ON SET2_PWM1ON_PWM0ON CLR1_PWM0ON CLR1_PWM1ON CLR2_PWM1ON_PWM0ON
INIT_NOT_PWM1ON_PWM0ON
INIT_PWM1ON_NOT_PWM0ON
Caution
If the above macros are used, the contents of the window register are destroyed. If an embedded macro instruction is used immediately before the above macro instructions, an "object error" occurs when the source file is assembled and then loaded to the in-circuit emulator. To use an embedded macro instruction immediately before the above macro instructions, insert a comment statement between them.
301
PD17016, 17017
24. RESERVED SYMBOL 24.1 Data Buffer (DBF)
Symbol Name DBF3 DBF2 DBF1 DBF0 Attribute MEM MEM MEM MEM Value 0.0CH 0.0DH 0.0EH 0.0FH R/W R/W R/W R/W R/W Bits 15 through 12 of DBF Bits 11 through 8 of DBF Bits 7 through 4 of DBF Bits 3 through 0 of DBF Description
24.2 System Register (SYSREG)
Symbol Name AR3 AR2 AR1 AR0 WR BANK IXH MPH MPE IXM MPL IXL RPH RPL PSW BCD CMP CY Z IXE Attribute MEM MEM MEM MEM MEM MEM MEM MEM FLG MEM MEM MEM MEM MEM MEM FLG FLG FLG FLG FLG Value 0.74H 0.75H 0.76H 0.77H 0.78H 0.79H 0.7AH 0.7AH 0.7AH.3 0.7BH 0.7BH 0.7CH 0.7DH 0.7EH 0.7FH 0.7EH.0 0.7FH.3 0.7FH.2 0.7FH.1 0.7FH.0 R/W R R R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W Description Bits 15 through 12 of address registerNote 1 Bits 11 through 8 of address registerNote 2 Bits 7 through 4 of address register Bits 3 through 0 of address register Window register Bank register Index register, high Memory pointer, high Memory pointer enable flag Index register, middle Memory pointer, low Index register, low General register pointer, high General register pointer, low Program status word BCD operation flag Compare flag Carry flag Zero flag Index enable flag
Notes 1. All the 4 bits are fixed to "0" with the PD17016. The high-order 3 bits are fixed to "0" with the PD17017. 2. The 4 bits are always fixed to "0" with the PD17016.
302
PD17016, 17017
24.3 LCD Segment Register
Symbol Name LCDD0 LCDD1 LCDD2 LCDD3 LCDD4 LCDD5 LCDD6 LCDD7 LCDD8 LCDD9 LCDD10 LCDD11 LCDD12 LCDD13 LCDD14 Attribute MEM MEM MEM MEM MEM MEM MEM MEM MEM MEM MEM MEM MEM MEM MEM Value 0.60H 0.61H 0.62H 0.63H 0.64H 0.65H 0.66H 0.67H 0.68H 0.69H 0.6AH 0.6BH 0.6CH 0.6DH 0.6EH R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W LCD segment register LCD segment register LCD segment register LCD segment register LCD segment register LCD segment register LCD segment register LCD segment register LCD segment register LCD segment register LCD segment register LCD segment register LCD segment register LCD segment register LCD segment register Description
24.4 Port Register
Symbol Name Attribute Value R/W Description
P0A3 FLG 0.70H.3 R/W Bit 3 of port 0A -----------------------------------------------------------------------------------------------------P0A2 FLG 0.70H.2 R/W Bit 2 of port 0A -----------------------------------------------------------------------------------------------------P0A1 FLG 0.70H.1 R/W Bit 1 of port 0A -----------------------------------------------------------------------------------------------------P0A0 FLG 0.70H.0 R/W Bit 0 of port 0A P0B3 FLG 0.71H.3 R/W Bit 3 of port 0B -----------------------------------------------------------------------------------------------------P0B2 FLG 0.71H.2 R/W Bit 2 of port 0B -----------------------------------------------------------------------------------------------------P0B1 FLG 0.71H.1 R/W Bit 1 of port 0B -----------------------------------------------------------------------------------------------------P0B0 FLG 0.71H.0 R/W Bit 0 of port 0B P0C3 FLG 0.72H.3 R/W Bit 3 of port 0C -----------------------------------------------------------------------------------------------------P0C2 FLG 0.72H.2 R/W Bit 2 of port 0C -----------------------------------------------------------------------------------------------------P0C1 FLG 0.72H.1 R/W Bit 1 of port 0C -----------------------------------------------------------------------------------------------------P0C0 FLG 0.72H.0 R/W Bit 0 of port 0C P0D3 FLG 0.73H.3 RNote Bit 3 of port 0D -----------------------------------------------------------------------------------------------------P0D2 FLG 0.73H.2 RNote Bit 2 of port 0D -----------------------------------------------------------------------------------------------------P0D1 FLG 0.73H.1 RNote Bit 1 of port 0D -----------------------------------------------------------------------------------------------------P0D0 FLG 0.73H.0 RNote Bit 0 of port 0D
Note
This port is an input port, but the assembler or in-circuit emulator does not output an error message even if an instruction that writes data to this port is described. Moreover, the operation is not affected even if such a program is actually executed on the device.
303
PD17016, 17017
24.4 Port Register
Symbol Name Attribute Value R/W Description
P0E3 FLG 0.6BH.3 R/W Bit 3 of port 0E -----------------------------------------------------------------------------------------------------P0E2 FLG 0.6BH.2 R/W Bit 2 of port 0E -----------------------------------------------------------------------------------------------------P0E1 FLG 0.6BH.1 R/W Bit 1 of port 0E -----------------------------------------------------------------------------------------------------P0E0 FLG 0.6BH.0 R/W Bit 0 of port 0E P0F3 FLG 0.6DH.3 R/W Bit 3 of port 0F -----------------------------------------------------------------------------------------------------P0F2 FLG 0.6DH.2 R/W Bit 2 of port 0F -----------------------------------------------------------------------------------------------------P0F1 FLG 0.6DH.1 R/W Bit 1 of port 0F -----------------------------------------------------------------------------------------------------P0F0 FLG 0.6DH.0 R/W Bit 0 of port 0F P1A3 FLG 1.70H.3 R/W Bit 3 of port 1A -----------------------------------------------------------------------------------------------------P1A2 FLG 1.70H.2 R/W Bit 2 of port 1A -----------------------------------------------------------------------------------------------------P1A1 FLG 1.70H.1 R/W Bit 1 of port 1A -----------------------------------------------------------------------------------------------------P1A0 FLG 1.70H.0 R/W Bit 0 of port 1A P1B3 FLG 1.71H.3 R/W Bit 3 of port 1B -----------------------------------------------------------------------------------------------------P1B2 FLG 1.71H.2 R/W Bit 2 of port 1B -----------------------------------------------------------------------------------------------------P1B1 FLG 1.71H.1 R/W Bit 1 of port 1B -----------------------------------------------------------------------------------------------------P1B0 FLG 1.71H.0 R/W Bit 0 of port 1B P1C3 FLG 1.72H.3 R/W Bit 3 of port 1C -----------------------------------------------------------------------------------------------------P1C2 FLG 1.72H.2 R/W Bit 2 of port 1C -----------------------------------------------------------------------------------------------------P1C1 FLG 1.72H.1 R/W Bit 1 of port 1C -----------------------------------------------------------------------------------------------------P1C0 FLG 1.72H.0 R/W Bit 0 of port 1C P1D3 FLG 1.73H.3 RNote Bit 3 of port 1D -----------------------------------------------------------------------------------------------------P1D2 FLG 1.73H.2 RNote Bit 2 of port 1D -----------------------------------------------------------------------------------------------------P1D1 FLG 1.73H.1 RNote Bit 1 of port 1D -----------------------------------------------------------------------------------------------------P1D0 FLG 1.73H.0 RNote Bit 0 of port 1D P2A0 FLG 2.70H.0 R/W Bit 0 of port 2A
Note
This port is an input port, but the assembler or in-circuit emulator does not output an error message even if an instruction that writes data to this port is described. Moreover, the operation is not affected even if such a program is actually executed on the device.
304
PD17016, 17017
24.5 Register File (control register)
(1/2)
Symbol Name SP Attribute MEM Value 0.81H R/W R/W Stack pointer Description
SIO1TS FLG 0.82H.3 R/W Serial interface transmit/receive start flag -----------------------------------------------------------------------------------------------------SIO1HIZ FLG 0.82H.2 R/W Serial interface/general-purpose port select flag -----------------------------------------------------------------------------------------------------SIO1CK1 FLG 0.82H.1 R/W Serial interface I/O clock setting flag -----------------------------------------------------------------------------------------------------SIO1CK0 FLG 0.82H.0 R/W Serial interface I/O clock setting flag IFCGOSTT PLLUL ADCCMP CE FLG FLG FLG FLG 0.84H.0 0.85H.0 0.86H.0 0.87H.0 R R R R IF counter gate status detection flag (1: open, 0: close) PLL unlock FF flag A/D converter compare result detection flag CE pin status detection flag
BTM1CK1 FLG 0.89H.3 R/W Timer interrupt mode select flag -----------------------------------------------------------------------------------------------------BTM1CK0 FLG 0.89H.2 R/W Timer interrupt mode select flag -----------------------------------------------------------------------------------------------------BTM0CK1 FLG 0.89H.1 R/W Timer carry FF mode select flag -----------------------------------------------------------------------------------------------------BTM0CK0 FLG 0.89H.0 R/W Timer carry FF mode select flag KSEN FLG 0.90H.1 R/W Key source signal output start flag -----------------------------------------------------------------------------------------------------LCDEN FLG 0.90H.0 R/W LCD driver display start flag IFCMD1 FLG 0.92H.3 R/W IF counter mode select flag (10: AMIF, 11: setting prohibited) -----------------------------------------------------------------------------------------------------IFCMD0 FLG 0.92H.2 R/W IF counter mode select flag (00: BEEP, 01: FMIF) -----------------------------------------------------------------------------------------------------IFCCK1 FLG 0.92H.1 R/W IF counter clock select flag -----------------------------------------------------------------------------------------------------IFCCK0 FLG 0.92H.0 R/W IF counter clock select flag ADCCH3 FLG 0.94H.3 R/W A/D converter channel select flag (dummy) -----------------------------------------------------------------------------------------------------ADCCH2 FLG 0.94H.2 R/W A/D converter channel select flag -----------------------------------------------------------------------------------------------------ADCCH1 FLG 0.94H.1 R/W A/D converter channel select flag -----------------------------------------------------------------------------------------------------ADCCH0 FLG 0.94H.0 R/W A/D converter channel select flag KEYJ BTM0CY FLG FLG 0.96H.0 0.97H.0 R R Key input judge flag Timer carry FF status detection flag
PLLMD3 FLG 0.0A1H.3 R/W PLL mode select flag (dummy: 0) -----------------------------------------------------------------------------------------------------PLLMD2 FLG 0.0A1H.2 R/W PLL mode select flag (dummy: 0) -----------------------------------------------------------------------------------------------------PLLMD1 FLG 0.0A1H.1 R/W PLL mode select flag -----------------------------------------------------------------------------------------------------PLLMD0 FLG 0.0A1H.0 R/W PLL mode select flag IFCSTRT FLG 0.0A3H.1 W IF counter count start flag -----------------------------------------------------------------------------------------------------IFCRES FLG 0.0A3H.0 W IF counter reset flag P0CGIO FLG 0.0A7H.0 R/W P0C input/output select flag
PLLRFCK3 FLG 0.0B1H.3 R/W PLL reference frequency select flag -----------------------------------------------------------------------------------------------------PLLRFCK2 FLG 0.0B1H.2 R/W PLL reference frequency select flag -----------------------------------------------------------------------------------------------------PLLRFCK1 FLG 0.0B1H.1 R/W PLL reference frequency select flag -----------------------------------------------------------------------------------------------------PLLRFCK0 FLG 0.0B1H.0 R/W PLL reference frequency select flag
305
PD17016, 17017
24.5 Register File (control register)
(2/2)
Symbol Name Attribute Value R/W Description
P1ABIO3 FLG 0.0B5H.3 R/W P1A3 input/output select flag -----------------------------------------------------------------------------------------------------P1ABIO2 FLG 0.0B5H.2 R/W P1A2 input/output select flag -----------------------------------------------------------------------------------------------------P1ABIO1 FLG 0.0B5H.1 R/W P1A1 input/output select flag -----------------------------------------------------------------------------------------------------P1ABIO0 FLG 0.0B5H.0 R/W P1A0 input/output select flag P0BBIO3 FLG 0.0B6H.3 R/W P0B3 input/output select flag -----------------------------------------------------------------------------------------------------P0BBIO2 FLG 0.0B6H.2 R/W P0B2 input/output select flag -----------------------------------------------------------------------------------------------------P0BBIO1 FLG 0.0B6H.1 R/W P0B1 input/output select flag -----------------------------------------------------------------------------------------------------P0BBIO0 FLG 0.0B6H.0 R/W P0B0 input/output select flag P0ABIO3 FLG 0.0B7H.3 R/W P0A3 input/output select flag -----------------------------------------------------------------------------------------------------P0ABIO2 FLG 0.0B7H.2 R/W P0A2 input/output select flag -----------------------------------------------------------------------------------------------------P0ABIO1 FLG 0.0B7H.1 R/W P0A1 input/output select flag -----------------------------------------------------------------------------------------------------P0ABIO0 FLG 0.0B7H.0 R/W P0A0 input/output select flag
24.6 Peripheral Hardware Register
Symbol Name ADCR SIO1SFR PWMR0 PWMR1 AR PLLR KSR IFC Attribute DAT DAT DAT DAT DAT DAT DAT DAT Value 02H 03H 05H 06H 40H 41H 42H 43H R/W R/W R/W R/W R/W R/W R/W R/W R Description A/D converter reference voltage setting register Serial interface presettable shift register PWM0 data register PWM1 data register Address register PLL data register Key source data register IF counter data register
24.7 Others
Symbol Name DBF IX Attribute DAT DAT Value 0FH 01H Description Fixed operand value of PUT, GET, and MOVT instructions Fixed operand value of INC instruction
306
PD17016, 17017
25. ELECTRICAL SPECIFICATIONS
Absolute Maximum Ratings (TA = 25 2 C)
Parameter Supply voltage Input voltage Output voltage Output breakdown voltage Symbol VDD VI VO VBDS1 VBDS2 High-level output current IOH Except P1B1 through P1B3, P0A2, P0A3 P1B1-P1B3 P0A2, P0A3 1 pin Total of all pins Low-level output current IOL 1 pin Total of all pins Operating ambient temperature Storage temperature TA Tstg Condition Rating -0.3 to +6.0 -0.3 to VDD + 0.3 -0.3 to VDD + 0.3 18.0 VDD + 0.3 -12 -20 12 20 -40 to +85 -55 to +125 Unit V V V V V mA mA mA mA C C
Caution
If the maximum absolute rating of even one of the above parameters is exceeded even momentarily, the quality of the product may degrade. The maximum absolute ratings, therefore, specify values exceeding which the product may be physically damaged. Never exceed these ratings when using the product.
Recommended Operating Conditions
Parameter Supply voltage Symbol VDD1 VDD2 Data retention voltage Supply voltage rise time Input amplitude VDDR trise VIN1 VIN2 Output breakdown voltage Operating ambient temperature VBDS TA Condition When PLL and CPU operate When PLL stops and CPU operates When crystal oscillation stops VDD = 0 4.5 V VCOL, VCOH AMIFC, FMIFC P1B1-P1B3 -40 0.5 0.5 MIN. 4.5 3.5 2.2 TYP. 5.0 5.0 MAX. 5.5 5.5 5.5 500 VDD VDD 16.0 +85 Unit V V V ms Vp-p Vp-p V C
307
PD17016, 17017
DC Characteristics (TA = -40 to +85 C, VDD = 4.5 to 5.5 V)
Parameter Supply voltage Symbol VDD1 VDD2 Supply current IDD1 Condition When CPU and PLL operate When CPU operates and PLL stops When CPU and PLL operate Sine wave input (fIN = 4.5 MHz, VIN = VDD), TA = 25 C XIN pin MIN. 4.5 3.5 TYP. 5.0 5.0 1.2 MAX. 5.5 5.5 2.4 Unit V V mA
IDD2
When CPU operates and PLL stops HALT instruction used (20 instructions executed every 1 ms) XIN pin sine wave input (fIN = 4.5 MHz, VIN = VDD), TA = 25 C Power failure detection by timer FF. During crystal oscillation Power failure detection by timer FF. When crystal oscillation stops Retention of data memory (RAM) When crystal oscillation stops When crystal oscillation stops VDD = 5.0 V, TA = 25 C TA = 25 C 3.5
0.45
0.90
mA
Data retention voltage
VDDR1
5.5
V
VDDR2
2.2
5.5
V
VDDR3 Data retention current IDDR1 IDDR2
2.0 2 2
5.5 15 10
V
A A
V V
Intermediate-level output voltage High-level input voltage
VOM1 VIH1
COM0, COM1 P0A0-P0A3, P0B0-P0B3, P0C0-P0C3, P1A0-P1A3, P1D0-P1D3 CE, INT0 P0D0-P0D3 P0A0-P0A3, P0B0-P0B3, P0C0-P0C3, P0D0-P0D3, P1A0-P1A3, P1D0-P1D3 CE, INT0
VDD = 5 V
2.3 0.8 VDD
2.5
2.7
VIH2 Low-level input voltage VIL
0.6 VDD 0.2 VDD
V V
High-level output current
IOH1
P0A0, P0A1, P1A0-P1A3, P2A0 VOH = VDD - 2 V, VDD = 5 V, TA = 25 C P0B0-P0B3, P0C0-P0C3, P1B0, P1C0-P1C3 LCD0-LCD29, EO0, EO1 VOH = VDD = -1 V VOH = VDD - 1 V
-2.0
-10
mA
IOH2
-1.0
-5.0
mA
IOH3 Low-level output current IOL1
-1.0 5.0
-4.0 15.0
mA mA
P0A0-P0A3, P1A0-P1A3, P2A0 VOL = 2 V, VDD = 5 V, TA = 25 C P0B0-P0B3, P0C0-P0C3, P1B0, P1C0-P1C3 LDC0-LDC29, EO0, EO1 P1B1-P1B3 With VCOH pulled down With VCOL pulled down With XIN pulled down With P0D0 through P0D3 pulled down P0A2, P0A3 P1B1-P1B3 EO0, EO1 VOL = 1 V VOL = 1 V VOL = 1 V VIH = VDD VIH = VDD VIH = VDD VIH = VDD VOH = VDD VOH = 16 V VOH = VDD, VOL = 0 V
IOL2
1.0
7.0
mA
IOL3 IOL4 High-level input current IIH1 IIH2 IIH3 IIH4 Output off leakage current IL1 IL2 IL3
1.0 1.0 0.1 0.1 0.1 0.05
3.5 2.0 0.8 0.8 1.3 0.13 0.30 500 500 100
mA mA mA mA mA mA nA nA nA
308
PD17016, 17017
AC Characteristics (TA = -40 to +85 C, VDD = 4.5 to 5.5 V)
Parameter Operating frequency Symbol fIN1 fIN2 fIN3 fIN4 fIN5 fIN6 fIN7 AD conversion resolution AD conversion total error TA = -10 to +50 C 1 Condition VCOL MF mode, sine wave input VCOL HF mode, sine wave input VCOH sine wave input AMIFC sine wave input AMIFC sine wave input FMIFC sine wave input FMIFC sine wave input VIN = 0.2 Vp-p VIN = 0.2 Vp-p VIN = 0.2 Vp-p VIN = 0.3 Vp-p VIN = 0.05 Vp-p VIN = 0.3 Vp-p VIN = 0.06 Vp-p MIN. 0.5 5 9 0.1 0.44 5 10.5 TYP. MAX. 30 40 150 1 0.46 15 10.9 6 1.5 Unit MHz MHz MHz MHz MHz MHz MHz bit LSB
Reference Characteristics
Parameter Supply current Symbol IDD3 Condition When CPU and PLL operate VCOH sine wave input fIN = 150 MHz, VIN = 0.3 Vp-p VDD = 5 V, TA = 25 C COM0, COM1 COM0, COM1 COM0, COM1 COM0, COM1 VOH = VDD - 1 V VOM = VDD - 1 V VOM = 1 V VOL = 1 V MIN. TYP. 15 MAX. Unit mA
High-level output current Intermediate-level output current Low-level output current
IOH3 IOM1 IOM2 IOL5
-0.2 -20 20 0.2
mA
A A
mA
309
PD17016, 17017
26. PACKAGE
Package of mass-produced model
80 PIN PLASTIC QFP (14 20)
A B
64 65
41 40
detail of lead end
CD
S Q R
80 1
25 24
F G H P I
M
J
K M N L
ITEM A B C D F G H I J K L M N P Q R S MILLIMETERS 23.20.2 20.00.2 14.00.2 17.20.2 1.0 1.8 0.350.10 0.15 0.8 (T.P.) 1.60.2 0.80.2 0.15 +0.10 -0.05 0.10 2.7 0.1250.075 55 3.0 MAX. INCHES 0.913 +0.009 -0.008 0.787 +0.009 -0.008 0.551 +0.009 -0.008 0.6770.008 0.039 0.031 0.014 +0.004 -0.005 0.006 0.031 (T.P.) 0.0630.008 0.031 +0.009 -0.008 0.006 +0.004 -0.003 0.004 0.106 0.0050.003 55 0.119 MAX. S80GF-80-3B9-3
NOTE Each lead centerline is located within 0.15 mm (0.006 inch) of its true position (T.P.) at maximum material condition.
Caution
The ES model differs from the mass-produced model in package and materials. Refer to the package drawing of the ES model.
310
PD17016, 17017
Package of ES model ES 80-PIN CERAMIC QFP (REFERENCE) (UNIT: mm)
20.0 18.4
64
41
12.0
1
24
14.2
0.8
0.32
2.25
0.15
Bottom surface
Cautions 1. The leads are diagonally molded on the bottom surface. 2. Because cutting of the tip of the lead is not subject to quality control, the lead length is not specified.
311
PD17016, 17017
27. RECOMMENDED SOLDERING CONDITIONS
Solder the PD17016 and 17017 under the following recommended conditions. For details of the recommended soldering conditions, refer to Information document Semiconductor Device Mounting Technology Manual (C10535E). For the soldering methods and conditions other than those recommended, consult NEC. Table 27-1. Soldering Conditions of Surface Mount Type
PD17016GF-xxx-3B9: 80-pin plastic QFP (14 x 20 mm) PD17017GF-xxx-3B9: 80-pin plastic QFP (14 x 20 mm)
Soldering Method Soldering Condition Symbol of Recommended Soldering Condition IR35-207-2
Infrared reflow
Package peak temperature: 235 C, Time: 30 seconds max. (210 C min.), Number of times: 2 max., Number of days: 7Note (After this, prebaking at 125 C for 20 hours is necessary.) Products other than those supplied in heat-resistance tray (magazine, taping, and heat-labile tray) cannot be baked in their packs. Package peak temperature: 215 C, Time: 40 seconds max. (200 C min.), Number of times: 2 max., Number of days: 7Note (After this, prebaking at 125 C for 20 hours is necessary.) Products other than those supplied in heat-resistance tray (magazine, taping, and heat-labile tray) cannot be baked in their packs. Solder bath temperature: 260 C max., Time: 10 seconds max., Number of times: 1, Preheating temperature: 120 C max. (package surface temperature), Number of days: 7Note (After this, prebaking at 125 C for 20 hours is necessary.) Pin temperature: 300 C max., Time: 3 seconds max. (per side of device)
VPS
VP15-207-2
Wave soldering
WS60-207-1
Partial heating
-
Note
The number of days for which the device can be left at 25 C, 65 % RH max. after the dry pack has been opened.
Caution
Do not use two or more soldering methods in combination (except the partial heating method).
312
PD17016, 17017
APPENDIX A. NOTE ON CONNECTING CRYSTAL RESONATOR
When using the system clock oscillation circuit, the following points must be noted in wiring the portion indicated by the dotted line in the figure below to prevent adverse influence from wiring capacitance. * Keep the wiring length as short as possible. * If capacitances C1 and C2 are too high, the oscillation start characteristic may be degraded or the current consumption may increase. * Generally, connect the trimmer capacitor for adjusting the oscillation frequency to the XIN pin. Depending on the crystal resonator used, however, the oscillation stabilization differs. Therefore, evaluate the crystal resonator actually to be used. * The crystal frequency cannot be accurately adjusted because of probe capacitance if an emulation probe is connected to the XOUT or XIN pin. Adjust the frequency while measuring the LCD drive waveform (125 Hz) or VCO oscillation frequency.
PD17016 PD17017
XOUT XIN
4.5-MHz crystal resonator
C1
C2
313
PD17016, 17017
APPENDIX B. DIFFERENCES AMONG PD17016, 17017, 17003A, 17005, AND 17010
(1) Hardware
Item ROM RAM Output port Control register General register pointer Stack level Serial interface 16 KB (7932 x 16 bits) 432 x 4 bits 13 pins (+30: LCD segment pins) 41 x 4 bits 5 bits 9 levels
PD17010
PD17003A
8 KB (3836 x 16 bits) 320 x 4 bits
PD17005
16 KB (7932 x 16 bits) 432 x 4 bits
9 pins (+30: LCD segment pins) 33 x 4 bits 4 bits 7 levels
2 modes (3 channels): serial I/O mode, I2C bus mode * SIO0 clock 37.5, 75, 112.5, 225 kHz * SIO1 clock External, 37.5, 75, 450 kHz * Hysteresis characteristics for SCL, SDA, SCK0, SCK1, SI0, and SI1 pins * SIO1 clock 75, 150, 225, 450 kHz * SIO2 clock External, 75, 150, 450 kHz
D/A converter frequency D/A converter output (PWM) Interrupt
4394.5 Hz 3 channels * 6 sources External: 1 source (INT0 pin) Internal : 4 sources (TM, BTM1, SIO0, IFC) External/internal: 1 source (INT1 pin or overflow of timer/counter) * Interrupt priority (vector address) 1. (6H) INT0 pin 2. (5H) INT1 pin (shared with overflow of timer/counter) 3. (4H) 12-bit timer 4. (3H) Basic timer 1 5. (2H) Serial interface 0 6. (1H) Frequency counter * Automatic saving of system register (3 levels) (WR, BANK, RP, PSWORD) * Address change of IRQxxx flag * Basic timer 0 carry (1, 5, 100, 250 ms) * Basic timer 1 interrupt (1, 5, 100, 250 ms) * 12-bit timer (10 s to 4095 ms)
878.9 Hz
* 5 sources External: 2 sources (INT0 and INT1 pins) Internal : 3 sources (TM, SIO1, IFC)
* Interrupt 1. (5H) 2. (4H) 3. (3H) 4. (2H) 5. (1H)
priority (vector address) INT0 pin INT1 pin Timer Serial interface 1 Frequency counter
* Automatic saving of system register (4 levels) (BANK, IXE) * Timer carry (1, 5, 100, 250 ms) * Timer interrupt (1, 5, 100, 250 ms)
Timer
Frequency counter Clock generator port (CGP)
Frequency measurement (IF measurement) and external gate width measurement functions selectable * CGP output: 1 line * SG (Signal Generator) function * VDP (Variable Duty Pulse) function Provided (Unlock detection by program. Unlock FF delay time selectable) None Provided
PLL frequency synthesizer phase comparator Operational amplifier for PLL frequency synthesizer lowpass filter Package
80-pin plastic QFP (14 x 20 mm)
314
PD17016, 17017
PD17016
8 KB (3836 x 16 bits) 320 x 4 bits
PD17017
16 KB (7932 x 16 bits) 432 x 4 bits
9 pins (+8: LCD segment pins) 19 x 4 bits 4 bits 7 levels 1 channel: serial I/O mode * SIO1 clock External, 75, 150, 450 kHz
878.9 Hz 2 channels * 2 sources External: 1 source (INT0 pin) Internal : 1 source (timer)
* Interrupt priority (vector address) 1. (5H) INT0 pin 2. (3H) Timer
* Automatic saving of system register (4 levels) (BANK, IXE) * Timer carry (1, 5, 100, 250 ms) * Timer interrupt (1, 5, 100, 250 ms)
Frequency measurement function only None (BEEP output provided)
Internal (without unlock FF delay time select function) None
80-pin plastic QFP (14 x 20 mm)
315
PD17016, 17017
(2) Software
Item Setting of LCD segment output or output port of LCD22/P0E0 through LCD29/P0F3 pins Setting of output port or PWM output of P1B1/PWM0 and P1B2/PWM1 pin Interrupt request lag Write (POKE) instruction and flag manipulation embedded macroinstructions can be used. If write (POKE) instruction is used, error occurs during assembly. If flag manipulation embedded macroinstruction is used, error occurs during assembly. Subjected flags * IRQIFC * IRQSIO1 * IRQTM * IRQ1 * IRQ0 To write above flags, use macro library IRQ.MAC.
PD17010
PD17003A
PD17005
PD17016
PD17017
Write (POKE) instruction and flag manipulation embedded macroinstructions can be used.
Manipulated by software macro supplied with device file.
Enabling interrupt
Write (POKE) instruction and flag manipulation embedded macroinstructions can be used. Write (POKE) instruction and embedded macroinstructions SKTn and SKFn can be used. Read (PEEK) instruction is used. At this time, "0" is always read. SETn instruction can be also used. If read (PEEK) instruction is used, error occurs during assembly. Therefore, macroinstructions that creates PEEK instruction to object when they are expanded to SETn instruction must not be used. Subjected flags * IFCRES * IFCSTRT To read above flags, use macro library IFCSET.LIB. Manipulated by software macro supplied with device file.
Level judge of INT0 pin
IF counter control register
BEEP output setting
None
(3) Development tools
Item Hardware SE board Emulation probe Software Device file Macro library
PD17010
SE-17010 EP-17003GF AS17010 None
PD17003A
PD17005
PD17016
PD17017
AS17003 * IFCSET.LIB * IRQ.MAC
AS17005
AS17016 * IFCSET.LIB * D17016.INC * IFCSET.LIB * D17017.INC
One-time PROM
PD17P010
PD17P005
316
PD17016, 17017
(4) Notes on reserved word names The reserved words of the control registers of the PD17016 and 17017 are different from some reserved words of the PD17003A and 17005. The following table shows the differences in the reserved words between the PD17016/17017 and
PD17003A/17005. Note that this table shows only the different reserved words.
Item Timer
PD17003A
TMMD3 TMMD2 TMMD1 TMMD0 TMCY
PD17005
PD17016
BTM1CK1 BTM1CK0 BTM0CK1 BTM0CK0 BTM0CY None
PD17017
PLL frequency synthesizer
PLULDLY3 PLULDLY2 PLULDLY1 PLULDLY0 PLLRFMD3 PLLRFMD2 PLLRFMD1 PLLRFMD0
PLLRFCK3 PLLRFCK2 PLLRFCK1 PLLRFCK0 None
D/A converter
PWM2ON PWM1ONNote PWM0ONNote CGPON
LCD controller/driver
P0YON P0XON P0EONNote P0FONNote
None
Frequency counter Serial interface
IFCG SIO2TS SIO2HIZ SIO2CK1 SIO2CK0 SIO1CH SB SIO1MS SIO1TX SBACK
IFCGOSTT SIO1TS SIO1HIZ SIO1CK1 SIO1CK0 None
Note
These reserved words are manipulated by software macros with the PD17016 and 17017.
317
PD17016, 17017
Item Serial interface
PD17003A
SIO1NWT SIO1WRQ1 SIO1WRQ0 SIO1SF8 SIO1SF9 SBBSY SBSTT SIO1IMD3 SIO1IMD2 SIO1IMD1 SIO1IMD0 SIO1CK3 SIO1CK2 SIO1CK1 SIO1CK0
PD17005
PD17016
None
PD17017
Interrupt
INT1 INT0Note IEG1 IEG0 IPIFC IPSIO1 IPTMNote IP1 IP0 IRQIFC IRQSIO1 IRQTMNote IRQ1 IRQ0Note
None
Note
These reserved words are manipulated by software macros with the PD17016 and 17017.
318
PD17016, 17017
APPENDIX C. DEVELOPMENT TOOLS
The following development tools are available to support development of the program of the PD17016 and 17017. Hardware
Name In-circuit emulator IE-17K, IE-17K-ETNote 1, EMU-17KNote 2 Description IE-17K, IE-17K-ET, and EMU-17K are in-circuit emulators that can be commonly used with any model in 17K Series. IE-17K and IE-17K-ET are connected to host machine, which is PC-9800 series or IBM PC/ATTM, with RS-232-C. EMU-17K is mounted to expansion slot of PC-9800 series. When these in-circuit emulators are used in combination with system evaluation board (SE board) dedicated to each model, they operate as emulators corresponding to that model. When man-machine interface software SIMPLEHOST(R) is used, a more sophisticated debugging environment can be created. EMU-17K has a function for checking the contents of data memory real-time. SE-17010 is SE board for PD17016 and 17017. This SE board alone can be used to evaluate system or in combination with in-circuit emulator for debugging. EP-17003GF is emulation probe for PD17016GF and 17017GF. It connects SE board and target system when used with EV-9200G-80Note 3. EV-9200G-80 is conversion socket for 80-pin plastic QFP (14 x 20 mm) and is used to connect EP17003GF and target system. AF-9703, AF-9704, AF-9705, and AF-9706 are PROM programmers corresponding to PD17P005. They can program the PD17P005 when connected to program adapter AF-9803.
SE board (SE-17010) Emulation probe (EP-17003GF) Conversion socket (EV-9200G-80Note 3) PROM programmer AF-9703Note 4, AF-9704Note 4, AF-9705Note 4, AF-9706Note 4 Program adapter (AF-9803Note 4)
AF-9803 is adapter for programming PD17P005, and is used in combination with AF-9703, AF-9704, AF-9705, or AF-9706.
Notes 1. Low-cost model: external power supply type 2. This is a product by I.C Corp. For details, consult I.C Corp. (Tokyo, 03-3447-3793) 3. One EV-9200G-80 is provided with the EP-17003GF. Five EV-9200G-80s are also available as a set. 4. These are products of Ando Electric Co., Ltd. For details, consult Ando Electric Co, Ltd. (Tokyo, 033733-1163).
319
PD17016, 17017
Software
Name Description Host Machine OS MS-DOSTM Supply Media 5"2HD 3.5"2HD IBM PC/AT PC DOSTM 5"2HC 3.5"2HC PC-9800 series MS-DOS 5"2HD 3.5"2HC IBM PC/AT PC DOS 5"2HC 3.5"2HC Support software (SIMPLEHOST) Order Code
17K series assembler (AS17K)
AS17K is an assembler that can be commonly used with any model of 17K series. To develop program of PD17016 and 17017, this AS17K is used in combination with device file (AS17016). AS17016 contains device file for PD17016 and 17017. It is used in combination with 17K series assembler (AS17K).
PC-9800 series
S5A10AS17K S5A13AS17K S7B10AS17K S7B13AS17K S5A10AS17016 S5A13AS17016 S7B10AS17016 S7B13AS17016 S5A10IE17K S5A13IE17K S7B10IE17K S7B13IE17K
Device file (AS17016)
SIMPLEHOST is software that serves as man-machine interface on WindowsTM when program is developed by using in-circuit emulator and personal computer.
PC-9800 series
MS-DOS
Windows
5"2HD 3.5"2HD
IBM PC/AT
PC DOS
5"2HC 3.5"2HC
Remark The following versions of OSs are supported.
OS MS-DOS PC DOS Windows Version Ver.3.30 to Ver.5.00ANote Ver.3.1 to Ver.5.0Note Ver.3.0 to Ver.3.1
Note
MS-DOS Ver.5.00/5.00A and PC DOS Ver.5.0 have a task swap function, but this function cannot be used with this software.
320
PD17016, 17017
[MEMO]
321
PD17016, 17017
NOTES FOR CMOS DEVICES
1 PRECAUTION AGAINST ESD FOR SEMICONDUCTORS
Note: Strong electric field, when exposed to a MOS device, can cause destruction of the gate oxide and ultimately degrade the device operation. Steps must be taken to stop generation of static electricity as much as possible, and quickly dissipate it once, when it has occurred. Environmental control must be adequate. When it is dry, humidifier should be used. It is recommended to avoid using insulators that easily build static electricity. Semiconductor devices must be stored and transported in an anti-static container, static shielding bag or conductive material. All test and measurement tools including work bench and floor should be grounded. The operator should be grounded using wrist strap. Semiconductor devices must not be touched with bare hands. Similar precautions need to be taken for PW boards with semiconductor devices on it.
2 HANDLING OF UNUSED INPUT PINS FOR CMOS
Note: No connection for CMOS device inputs can be cause of malfunction. If no connection is provided to the input pins, it is possible that an internal input level may be generated due to noise, etc., hence causing malfunction. CMOS device behave differently than Bipolar or NMOS devices. Input levels of CMOS devices must be fixed high or low by using a pull-up or pull-down circuitry. Each unused pin should be connected to VDD or GND with a resistor, if it is considered to have a possibility of being an output pin. All handling related to the unused pins must be judged device by device and related specifications governing the devices.
3 STATUS BEFORE INITIALIZATION OF MOS DEVICES
Note: Power-on does not necessarily define initial status of MOS device. Production process of MOS does not define the initial operation status of the device. Immediately after the power source is turned ON, the devices with reset function have not yet been initialized. Hence, power-on does not guarantee out-pin levels, I/O settings or contents of registers. Device is not initialized until the reset signal is received. Reset operation must be executed immediately after power-on for devices having reset function.
322
PD17016, 17017
Regional Information
Some information contained in this document may vary from country to country. Before using any NEC product in your application, please contact the NEC office in your country to obtain a list of authorized representatives and distributors. They will verify: * Device availability * Ordering information * Product release schedule * Availability of related technical literature * Development environment specifications (for example, specifications for third-party tools and components, host computers, power plugs, AC supply voltages, and so forth) * Network requirements In addition, trademarks, registered trademarks, export restrictions, and other legal issues may also vary from country to country.
NEC Electronics Inc. (U.S.)
Mountain View, California Tel: 800-366-9782 Fax: 800-729-9288
NEC Electronics (Germany) GmbH
Benelux Office Eindhoven, The Netherlands Tel: 040-2445845 Fax: 040-2444580
NEC Electronics Hong Kong Ltd.
Hong Kong Tel: 2886-9318 Fax: 2886-9022/9044
NEC Electronics (Germany) GmbH
Duesseldorf, Germany Tel: 0211-65 03 02 Fax: 0211-65 03 490
NEC Electronics Hong Kong Ltd. NEC Electronics (France) S.A.
France Tel: 01-30-67 58 00 Fax: 01-30-67 58 99 Seoul Branch Seoul, Korea Tel: 02-528-0303 Fax: 02-528-4411
NEC Electronics (UK) Ltd.
Milton Keynes, UK Tel: 01908-691-133 Fax: 01908-670-290
NEC Electronics (France) S.A.
Spain Office Madrid, Spain Tel: 01-504-2787 Fax: 01-504-2860
NEC Electronics Singapore Pte. Ltd.
United Square, Singapore 1130 Tel: 253-8311 Fax: 250-3583
NEC Electronics Italiana s.r.1.
Milano, Italy Tel: 02-66 75 41 Fax: 02-66 75 42 99
NEC Electronics Taiwan Ltd. NEC Electronics (Germany) GmbH
Scandinavia Office Taeby Sweden Tel: 8-63 80 820 Fax: 8-63 80 388 Taipei, Taiwan Tel: 02-719-2377 Fax: 02-719-5951
NEC do Brasil S.A.
Sao Paulo-SP, Brasil Tel: 011-889-1680 Fax: 011-889-1689
J96. 3
323
PD17016, 17017
SIMPLEHOST is a registered trademark of NEC Corporation.
MS-DOS and Windows are trademarks of Microsoft Corporation. PC/AT and PC DOS are trademarks of IBM Corporation.
The export of this product from Japan is regulated by the Japanese government. To export this product may be prohibited without governmental license, the need for which must be judged by the customer. The export or re-export of this product from a country other than Japan may also be prohibited without a license from that country. Please call an NEC sales representative.
No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Corporation. NEC Corporation assumes no responsibility for any errors which may appear in this document. NEC Corporation does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from use of a device described herein or any other liability arising from use of such device. No license, either express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Corporation or others. While NEC Corporation has been making continuous effort to enhance the reliability of its semiconductor devices, the possibility of defects cannot be eliminated entirely. To minimize risks of damage or injury to persons or property arising from a defect in an NEC semiconductor device, customers must incorporate sufficient safety measures in its design, such as redundancy, fire-containment, and anti-failure features. NEC devices are classified into the following three quality grades: "Standard", "Special", and "Specific". The Specific quality grade applies only to devices developed based on a customer designated "quality assurance program" for a specific application. The recommended applications of a device depend on its quality grade, as indicated below. Customers must check the quality grade of each device before using it in a particular application. Standard: Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots Special: Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) Specific: Aircrafts, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems or medical equipment for life support, etc. The quality grade of NEC devices is "Standard" unless otherwise specified in NEC's Data Sheets or Data Books. If customers intend to use NEC devices for applications other than those specified for Standard quality grade, they should contact an NEC sales representative in advance. Anti-radioactive design is not implemented in this product.
M4 96.5
324

▲Up To Search▲

Price & Availability of UPD17016

	To Download UPD17016 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .